DIN 55803-1979 Machine Tools Spinning and Planishing Lathes Acceptance Conditions《机床 旋压机和碾平机 验收条件》.pdf

1、UDC 621.982.06: 621.983.4.06: 620.1 DEUTSCHE NORMEN December 1979 Type: DIN 55 803 Machine Tools Spinning and Planishing Lathes Acceptance Conditions Machine No.: Year of construction: Werkzeugmaschinen; Drck- und Planiermaschinen, Abnahmebedingungen Place: Accepted by : Date: 1 Purpose and field of

2、 application This Standard lays down the technical acceptance conditions for spinning and planishing lathes. They cover preparatory measures and geometrical tests of the machine (manufacturing accuracy). The test conditions correspond to DIN 8601 (Preliminary Standard), which complies with the Inter

3、national Recom- mendation ISO/R 230. If all the tests are not completed, or if additional tests are necessary, this must be agreed between the manufacturer and the user. The appropriate German regulations must be observed for the testing of the safety-related condition of the machine. The test proce

4、dures only give the test principle and the recommended test equipment which is usual in most firms, Other test procedures according to DIN 8601 (Preliminary Standard) of the same degree of accuracy are per- m iss bl e. In the column “Test instructions“, the relevant section number from DIN 8601 (Pre

5、liminary Standard), December 1977 edition, is given at the end in cases where the test concerned corresponds to the stipulations contained therein. 2 Other relevant Standards DIN 877 Precision levels; terms, requirements, permissible deviations, testing DIN 879 Part 1 Precision dial gauge with mecha

6、nical display DIN 8601 (Preliminary Standard) Machine tools; acceptance conditions for machine tools for the machine cutting of metals; general rules Continued on pages 2 to 5 Explanations on page 6 Sole sale rights of German Standards (DIN-Normen) are with Beuth Verlag GmbH. Berlin 30 and Kln 1 DIN

7、 55 803 engl. Preisgr. 5 02.81 VerIr.-Nr. O105 Page 2 DIN 55 803 3 Designations German Bett Spindelstock Arbeitsspindel Zentrierung Querschlitten Werkzeugtrager Druck kopf Pinole Lngsschl itten Reitstock - _ / English French Bed Banc Spindle head (Headstock) Poupe porte-broche Workspindle Broche Cen

8、tering Centrage Cross slide Chariot transversal Toolholder Porte-outil Pressure head Tte de pression Center sleeve Fourreau Longitudinal slide Chariot longitudinal Tailstock Con tre-poupe No 9 DIN 55 803 Page 3 No 4 Preparatory measures Subject of the test . Adj u sti ng the machine a in the longitu

9、dinal direction o1 b in the transverse direction ab a 5 Geometrical tests Trueness of the center- ing on the workspindle a outside b inside Surface true- ness of the contact sur- faces of the workspindle a outer centering b inner centering Diagram a b n u a b n U Test equipment Precision level ac- c

10、ording to DIN 877 Measuring bridge Test blocks or other test aids Measuring column Precision dial gauge according to DIN 879 Part 1 Measuring column Precision dial gauge according to DIN 879 Part 1 Test instructions The tests are to be carried out at dif- ferent points of thc slideways or the sight

11、i ng surf aces. Place the precision level on the slide- ways or the sight- ing surfaces and read off the indi- cation. 3.1.1 3.2 Secure the meas- uring column with the precision dial gauge to a fixed part of the machine. Position the gauge pin of the precision dial gauge at a right angle to the oute

12、r surface of the cen- terings at the workspindle at a on the outside, or at b on the inside diameter. Rotate the spindle and read off the indication. 5.6.1 Secure the meas- uring column with the precision dial gauge to a fixed part of the machine. Position the gauge pin of the preciqion dial gauge a

13、t the maxi- mum possible dia meter at al on the contact furfaces of the workspindle Rotate the spindle to a2 and read off the change in the indication. Repeat the test in the same way at b. 5.6.3 Deviations permissible For 1000 mm gauge length a 0.04 mm b 0.04 mm For a and b workpiece swing dia- met

14、er up to 800 mm 0.02 mm over 800 rnm up to 2000 mm 0.04 mm over 2000 mm 0.06 mm For a and b contact sur- face dia- meter up to 300 mm 0.03 mm over 300 mm 0.06 mm measured a . b . a b . a b . a b . a b . a b . Page 4 DIN 55 803 Subject of the test Trueness of the center- ings on the center sleeve a o

15、uter b inner Surface true- ness of the rontact cur- faces of the :entre sleeve a outer centering b inner centering Diagram b a b Test equipment Measuring column Precision dial gauge accord i ng to DIN 879 Part 1 Measuring column Precision dial gauge according to DIN 879 Part 1 Test instructions Secu

16、re the meas- uring column with the precision dial gauge to a fixed part of the machine. Position the gauge pin at a right angle to the outer surface of the centering at a, rotate the spindle and read off the indication. Conduct the test on the inner dia- meter of the cen- tering at b in the same man

17、ner. 5.6.1 Secure the meas- uring column with the precision dial gauge to a fixed part of the machine. Position the gauge pin of the precision dial gauge at the maxi- mum possible dia- meter at a, on the contact surfaces of the center sleeve. Rotate the spindle to a2 and read off the changi in the i

18、ndication. Repeat the test in the same way at b. 5.6.3 Deviations permissible For a and b workpiece swing dia- meter up to 800 mm 0.02 mm over 800 mm up to 2000 mm 0.03 mm over 2000 mm 0.04 mm For a and b contact sur- face dia- meter up to 800 mm 0.02 mm over 800 mm up to 2000 mm 0.03 mm over 2000 m

19、m 0.04 mm measured a b . a b . a b . a b a b a b DIN 55 803 Page 5 Subject of the test Alignment of the axes of the work- spindle and the center sleeve a in the vertical plane b in the horizontal plane Position I: Center sleeve en- gaged Position II: Center sleeve re- tracted Parallelism of the axes

20、 of the work- spindle and the center sleeve to the movement of the lon- gitudinal slide in the vertical plant Diagram JI I al, a3 I Test equipment Test mandrel Travel arm Precision dial gauge according to DIN 879 Part 1 Measuring column Precision dial gauge according to DIN 879 Part 1 Test mandrel T

21、est instructions Secure the test mandrel with the travel arm in the mounting of the workspindle. Place the gauge pin of the preci- sion dial gauge at the engaged center sleeve in the ver- tical plane at al (I) and read off the indication. Rotate the travel arm through 180 to a2 and read off the indi

22、cation. Calculate the mean value. Repeat the test in the horizontal plane at b, and b2: Then retract the center sleeve (II) and at a distance of 300 mm repeat the test in both the vertical and the horizontal planes. Secure the test mandrel in the workspi nd I e mounting and the center sleeve. Place

23、gauge pin of the precision dial gauge against the mandrel. Move the longitudinal slide by the gauge length and read off the indication. Deviations permissible For work- piece swing diameter up to 800 mm I a = 0,05 mm b = 0,04 mm II a = 0,l mm b = 0.08 mm over 800 mm up to 2000 mm I a = 0,l mm b = 0,

24、05 mm II a = 0,2 mm b= 0,15mm over 2000 mm I a = 0,2 mm b = 0.1 mm II a = 0,3 mm b = 0,2 mm Center sleeve point- ing to the workspindle only rising 0,2 mm on 300 mm gauge length measured a b a b a b a b a b a . b ;auge length : Page 6 DIN 55 803 Explanations For spinning and planishing lathes, it is sufficient for the trueness and surface trueness at the workspindle and the tailstock center sleeve together with the alignment of both axes to be tested. With regard to the wide range of applications of these machines, a practical test was not included.