DIN 626-1-1999 Rolling bearings - Bearings with spherical outside surface and extended inner ring width - Part 1 Insert bearings《滚动轴承 带球形外表面和增加内环宽度的轴承 第1部分 镶嵌轴承》.pdf

1、DEUTSCHE NORM Julv 1999 Rolling bearings with spherical outside surface and extended inner ring Part 1 : Insert bearings DIN 626-1 - ICs 21.1 00.20 Supersedes February 1979 edition Wlzlager - Rillenkugellager mit kugelfrmiger Auenringmantelflche und verbreitertem Innenring - Teil 1 : Spannlager In k

2、eeping with current practice in standards published by the International Organization for Standardization (ISO), a comma has been used throughout as the decimal marker. Foreword This standard has been prepared by the Arbeitsausschuss Walzlager (Rolling Bearings Standards Com- mitt ee) . It conforms

3、in substance to IS0 9628 : 1992, except that a) insert bearings with concentric locking collar around the inner ring and the specifications relating to inner ring eccentric extension and radial internal clearance have not been included; b) the range of nominal sizes covered in tables 1 to 3 has been

4、 extended to include 1 O0 mm; c) tables 1 to 3 have been supplemented by the addition of columns for dimensionB, mass and symbol. Amendments This standard differs from the February 1979 edition in that it has been editorially revised and type YAL insert bearings have been included. Previous edition

5、DIN 626-1 : 1979-02. All dimensions are in mm. 1 Scope This standard specifies the dimensions, mass and bore diametertolerances for three types of rolling bearing with a spherical outside surface and an extended inner ring with a locking device. Type YEL and YEN bearings have an eccentric locking co

6、llar for fixing the inner ring to the shaft (see figures 1 and 2), and type YAL bearings are fixed to the shaft by means of set screws in the inner ring (see figure 3). The outer ring of all three types of bearing has a spherical outside surface so that the bearing can be mounted in a housing with a

7、 matching spherical seat, thus providing correct alignment. Using these bearings with housings complying with DIN 626-2 reduces the need for expensive machining processes, and allows the use of standard shafts. 2 Normative references This standard incorporates, by dated or undated reference, provisi

8、ons from other publications. These normative references are cited at the appropriate places in the text, and the titles of the publications are listed below. For dated references, subsequent amendments to or revisions of any of these publications apply to this standard only when incorporated in it b

9、y amendment or revision. For undated references, the latest edition of the publication referred to applies. DIN 616 DIN 620-2 DIN 620-4 DIN 625-1 Rolling bearings - General plan Tolerances for radial ball bearings Tolerances on radial internal clearance of rolling bearings Single row radial contact

10、ball bearings Continued on pages 2 to 6. Translation by DIN-Sprachendienst. In case of doubt, the German-language original should be consulted as the authoritative text. No pari of this translation may be reproduced without the prior permission of Ref. No. DIN 626-1 : 1999-0 V Deutsches Institut fr

11、Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, s the exclusive right of sale for German Standards (DIN-Normen). English price group 06 Sales No. 0106 06.00 Page 2 DIN 626-1 : 1999-07 DIN 626-2 Rolling bearings with spherical outside surface and extended inner ring - Housings for in

12、sert bearings DIN 17230 Steel for rolling bearings - Technical delivery conditions DIN 51 825 Type K lubricating greases - Classification and requirements IS0 11 32 : 1980 Rolling bearings - Tolerances - Definitions IS0 5593 : 1997 Rolling bearings - Vocabulary IS0 9628 : 1992 Rolling bearings - Ins

13、ert bearings and eccentric locking collars 3 Concepts See IS0 11 32 and IS0 5593. 4 Dimensions and designation The dimensions and designation of insert bearings shall be as given in subclause 4.1. Design details not given here remain unspecified. The bore diameters and outside diameters given in tab

14、les 1 to 3 correspond to diameter series 2 as given in DIN 616, except for nominal sizes, d, of 12 mm, 15 mm, and 65 mm. The inner ring widths specified here are greater than those specified in DIN 61 6. For type YEL and YEN bearings, where the locking device extends axially beyond the inner ring, t

15、he width over the locking device, called the overall width (B,), is specified. For type YAL bearings, where the locking device is not axially extending beyond the inner ring, dimension B is the overall inner ring width. In accordance with IS0 9628, the three overall width series given are designated

16、 wide (type YEL), intermediate (type YAL) and narrow (type YEN). 4.1 Types 4.1.1 Type YEL insert bearing with eccentric locking collar (wide overall width) locking IW I collar B, Figure 1: Bearing with eccentric locking collar, inner ring extended on both sides - Wide overall width (see table 1) Des

17、ignation of an insert bearing of type YEL, with a bore diameter, d, of 25 mm (denoted by YEL 205): Bearing DIN 626 - YEL 205 Page 3 DIN 626-1 : 1999-07 Outside diameter, D size, d B, B S c Ca dl B2 - - - - max. - max. - - 17 20 25 30 62 48,4 36,5 18,3 19 5 44,5 15,9 35 72 51,l 37,7 18,8 20 5,7 55,6

18、17,5 40 37,3 27,8 13,9 15 3,4 28,6 13,5 47 43,7 34,l 17,l 17 3,7 33,3 13,5 52 44,4 34,9 17,5 17 3,9 38,l 13,5 40 80 56,3 42,9 21,4 21 6,2 60,3 18,3 45 85 56,3 42,9 21,4 22 6,4 63,5 18,3 Approx I Symbol I mass, in kg :il IYEL203 I YEL 204 :2: IYEL205 YEL 206 I -1 YEL 21 1 IYEL212 I YEL 214/65 :4: IYE

19、L214 I YEL 215 4.1.2 Type YEN insert bearing with eccentric locking collar (narrow overall width) 4,65 IYEL220 locking Figure 2: Bearing with eccentric locking collar, inner ring extended on one side - Narrow overall width (see table 2) Designation of an insert bearing of type YEN, with a bore diame

20、ter, d, of 15 mm (denoted by YEN 203/15): Bearing DIN 626 - YEN 203/15 Page 4 DIN 626-1 : 1999-07 Outside diameter, D size, d Table 2: Dimensions, mass and symbols (type YEN) Symbol Ca dl B2 Approx. B, B S c mass, in kg - - - - max. - max. - - 15 17 I 12 I 40 I 28.6 I 19.1 I 6.5 I 13 I 3.4 I 28.6 I

21、13.5 I 0.13 IYEN203/121 40 28,6 19,l 6,5 13 3,4 28,6 13,5 0,12 YEN 203/15 40 28,6 19,l 6,5 13 3,4 28,6 13,5 0,11 YEN203 20 25 47 31 21,4 7,5 15 3,7 33,3 13,5 0,17 YEN204 52 31 21,4 7,5 15 3,9 38,l 13,5 0,20 YEN205 30 35 62 35,7 23,8 9 18 5 44,5 15,9 0,31 YEN206 72 38,9 25,4 9,5 19 5,7 55,6 17,5 0,53

22、 YEN207 50 I 90 I 43.7 I 30.2 I 11 I 22 I 6.5 I 69.9 I 18.3 I 0.77 IYEN 210 40 45 80 43,7 30,2 11 22 6,2 60,3 18,3 0,63 YEN208 85 43,7 30,2 11 22 6,4 63,5 18,3 0,74 YEN209 4.1.3 Type YAL insert bearing with set screws in the inner ring (intermediate overall width) 55 60 S 1 O0 48,4 32,5 12 25 7 76,8

23、 20,7 0,82 YEN 211 110 53,l 37,l 13,5 27 7,6 84,2 22,3 1,40 YEN 212 Figure 3: Bearing with set screws in the inner ring, inner ring extended on both sides - Intermediate overall width (see table 3) Designation of an insert bearing of type YAL, with a bore diameter, d, of 40 mm (denoted by YAL 208):

24、Bearing DIN 626 - YAL 208 Page 5 DIN 626-1 : 1999-07 size, d 12 15 Symbol Ca Approx. Outside B S c mass, in kg diameter, - D - - max. - 40 27,4 11,5 15 3,4 0,ll YAL 203/12 40 27,4 11,5 15 3,4 0,l o YAL 203/15 - 17 20 40 27,4 11,5 15 3,4 0,09 YAL 203 47 31 12,7 17 3,7 0,17 YAL 204 25 30 52 34,l 14,3

25、17 3,9 0,20 YAL 205 62 38,l 15,9 19 5 0,33 YAL 206 50 55 90 51,6 19 24 6,s 0,80 YAL 21 O 1 O0 55,6 22,2 25 7 1,lO YAL 21 1 60 65 110 65,l 25,4 27 7,6 1,32 YAL 21 2 120 68,3 25,4 27 7,4 1,85 YAL 21 3 70 75 125 74,6 30,2 28 83 1,95 YAL 21 4 130 77,8 33,3 29 8,s 2,20 YAL 21 5 1 O0 180 I 108 42 40 I 11,

26、2 I 5,65 I YAL 220 I 35 I 72 I 42,9 I 17,5 I 20 I 5,7 I 0,49 I YAL207 1 I 40 I 80 I 49,2 I 19 I 21 I 6,2 I 0,65 I YAL208 1 I 45 I 85 I 49,2 I 19 I 22 I 6,4 I 0,70 I YAL209 1 I 80 I 140 I 82,6 I 33,3 I 30 I 8,8 I 2,95 I YAL216 1 I 90 I 160 I 96 I 39,7 I 36 I 10 I 4,20 I YAL218 1 Table 4: Tolerances N

27、ominal bore diameter, d. in mm Deviation of mean bearing bore diameter in a radial plane, Admp, as in IS01 132, in pm Upper deviation I Lower deviation Maximum variation of bearing bore diameter in a single radial plane, Vdp, as in IS0 11 32, in pm Over I up to 10 I 18 +15 I O 10 18 I 30 +18 I O 12

28、30 I 50 + 21 I O 14 50 I 80 +24 I O 16 80 I 120 +28 I O 19 4.3 Radial internal clearance The radial internal clearance of insert bearings shall comply with clearance range C3 as specified in DIN 620-4. 5 Materials Rolling elements and rings shall be made of steel as specified in DIN 17230, the mater

29、ial of the cage, eccentric locking collars, set screws and seals being at the manufacturers discretion. 6 Design Insert bearings are supplied with different types of seal of various sizes. The exact design of the seals is not specified in this standard. Page 6 DIN 626-1 : 1999-07 The bearings shall

30、be provided with lubrication holes. Details of such holes are not specified. Insert bearings may only be used without lubrication holes if so agreed. The cage design shall be at the manufacturers discretion. Design details regarding the eccentric locking collar and the set screws are not specified i

31、n this standard. 7 Lubrication Insert bearings shall be supplied greased, the lubricant used complying at least with the requirements specified in DIN 51825. 8 Service temperature ranges Bearings complying with this standard may be used at temperatures ranging from - 25 “C to 11 O “C. Bearings designed for use at other temperatures will be supplied on request.