DIN 660-2012 Round head rivets - Nominal diameters 1 mm to 8 mm《圆头铆钉 公称直径1 mm至8 mm》.pdf

1、January 2012 Translation by DIN-Sprachendienst.English price group 8No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).ICS

2、 21.060.40!$z9Y“1872254www.din.deDDIN 660Round head rivets Nominal diameters 1 mm to 8 mmEnglish translation of DIN 660:2012-01Halbrundniete Nenndurchmesser 1 mm bis 8 mmEnglische bersetzung von DIN 660:2012-01Rivets tte ronde Diamtres nominaux de 1 mm 8 mmTraduction anglaise de DIN 660:2012-01Super

3、sedesDIN 660:2011-03www.beuth.deDocument comprises 12 pagesIn case of doubt, the German-language original shall be considered authoritative.02.12 DIN 660:2012-01 2 A comma is used as the decimal marker. Contents Page Foreword . 3 1 Scope . 4 2 Normative references . 4 3 Dimensions 4 4 Technical deli

4、very conditions . 8 5 Designation . 9 6 Application 9 Bibliography . 12 DIN 660:2012-01 3 Foreword This standard has been prepared by Working Committee NA 067-00-09 AA Verbindungselemente ohne Gewinde of the Normenausschuss Mechanische Verbindungselemente (Fasteners Standards Committee). Attention i

5、s drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. The DIN 4000-163-5 tabular layout of product properties applies to rivets covered in this standard. Amendments T

6、his standard differs from DIN 660:1993-05 as follows: a) normative references have been updated; b) the designation has been changed; c) equations for calculating head and shank masses have been included; d) the figures have been updated; e) in Table 1 the range of mass values has been extended and

7、some of those values have been changed. Compared with DIN 660:2011-03 the following corrections have been made: a) Figures 2 and 3 have been corrected; b) in Table 1 dimensions k, r and r1have been corrected in compliance with DIN 660:1993-05; c) in Figure 2 d1has been substituted for d3; d) the val

8、ues of d8and k1 given in Table 5 are now to be understood as guideline values; e) the reference to the standard covering the relevant tabular layout of product properties has been rendered more precise. Previous editions DIN 660: 1926-10, 1944-03, 1956x-06, 1977-07, 1993-05, 2011-03 DIN 663: 1926-10

9、 DIN 660:2012-01 4 1 Scope This standard specifies dimensions, masses and technical delivery conditions for round head rivets with nominal diameters from 1 mm to 8 mm. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated referenc

10、es, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. DIN 101, Rivets Technical specifications DIN 4000-163, Tabular layout of product properties Part 163: Fasteners without thread DIN EN 1301-2, Aluminium and al

11、uminium alloys Drawn wire Part 2: Mechanical properties DIN EN 10263-2, Steel rod, bars and wire for cold heading and cold extrusion Part 2: Technical delivery conditions for steels not intended for heat treatment after cold working DIN EN 10263-5, Steel rod, bars and wire for cold heading and cold

12、extrusion Part 5: Technical delivery conditions for stainless steels DIN EN 12166, Copper and copper alloys Wire for general purposes DIN EN ISO 4042, Fasteners Electroplated coatings 3 Dimensions See Figure 1 and Table 1. Figure 1 Dimensions of round head rivet (nominal diameters from 1 mm to 8 mm)

13、 (notation) DIN 660:2012-01 5 Table 1 Dimensions and masses Dimensions in millimetres d1Nominal size 1 1,2 (1,4) 1,6 2 2,5 3 (3,5) 4 5 6 (7) 8 Limit deviations 0,05 0,1 0,15 d2Nominal size 1,8 2,1 2,4 2,8 3,5 4,4 5,2 6,2 7 8,8 10,5 12,2 14 Tolerances h14 h15 d3min. 0,93 1,13 1,33 1,52 1,87 2,37 2,87

14、 3,37 3,87 4,82 5,82 6,82 7,76 e max. 0,50 0,60 0,70 0,80 1,00 1,25 1,50 1,75 2,00 2,50 3,00 3,50 4,00 k js14 0,6 0,7 0,8 1,0 1,2 1,5 1,8 2,1 2,4 3,0 3,6 4,2 4,8 rmax. 0,2 0,3 0,4 r1 1,0 1,2 1,4 1,6 1,9 2,4 2,8 3,4 3,8 4,6 5,7 6,6 7,5 l Mass (7,85 kg/dm3) kg/1 000 units a Nominal size Limit deviatio

15、ns 2 +0,25 0 0,020 0,030 0,042 0,063 0,102 3 0,026 0,038 0,054 0,079 0,127 0,221 0,343 4 +0,30 0 0,032 0,047 0,066 0,094 0,152 0,259 0,398 0,596 0,820 5 0,038 0,056 0,078 0,110 0,176 0,298 0,454 0,672 0,919 1,57 6 0,044 0,065 0,091 0,126 0,201 0,336 0,509 0,747 1,02 1,72 2,77 8 +0,36 0 0,057 0,083 0

16、,115 0,158 0,250 0,413 0,620 0,898 1,21 2,03 3,21 4,68 6,50 10 0,069 0,101 0,139 0,189 0,299 0,490 0,731 1,05 1,41 2,34 3,66 5,28 7,29 12 0,082 0,119 0,163 0,221 0,348 0,567 0,842 1,20 1,61 2,65 4,10 5,89 8,08 14 +0,43 0 0,094 0,136 0,187 0,252 0,398 0,644 0,953 1,35 1,81 2,96 4,55 6,49 8,87 16 0,10

17、6 0,154 0,212 0,284 0,447 0,721 1,06 1,50 2,00 3,26 4,99 7,09 9,66 18 0,119 0,172 0,236 0,316 0,496 0,798 1,18 1,65 2,20 3,57 5,43 7,70 10,4 20 0,131 0,190 0,260 0,347 0,545 0,875 1,29 1,80 2,40 3,88 5,88 8,30 11,2 22 0,144 0,208 0,284 0,379 0,594 0,952 1,40 1,96 2,60 4,19 6,32 8,91 12,0 25 +0,52 0

18、0,162 0,234 0,320 0,426 0,668 1,07 1,56 2,18 2,89 4,65 6,99 9,81 13,2 28 0,181 0,261 0,357 0,474 0,742 1,18 1,73 2,41 3,19 5,11 7,65 10,7 14,4 30 0,193 0,279 0,381 0,505 0,791 1,26 1,84 2,56 3,38 5,42 8,10 11,3 15,2 32 0,206 0,297 0,405 0,537 0,840 1,34 1,95 2,71 3,58 5,73 8,54 11,9 16,0 35 +0,62 0

19、0,224 0,323 0,441 0,584 0,914 1,45 2,12 2,94 3,88 6,19 9,21 12,8 17,1 38 0,243 0,350 0,478 0,632 0,988 1,57 2,29 3,16 4,17 6,65 9,87 13,7 18,3 40 0,255 0,368 0,502 0,663 1,04 1,65 2,40 3,31 4,37 6,96 10,3 14,3 19,1 Lengths exceeding 40 mm shall be graded in 5 mm increments. Bracketed sizes and inter

20、mediate lengths should be avoided if possible. The values of mass specified are for guidance only. See Table 2 for a.DIN 660:2012-01 6 Table 2 Conversion factors for values of mass Material St, stainless steel Cu CuZn Al Conversion factor 1,000 1,134 1,070 0,344 Table 3 Shank and head masses (steel)

21、 Nominal size d11 1,2 (1,4) 1,6 2 2,5 3 Mass of shank per mm kg/1 000 units (7,85 kg/dm3) 0,006 2 0,008 9 0,012 1 0,015 8 0,024 6 0,038 5 0,055 5 Mass of head kg/1 000 units (7,85 kg/dm3) 0,007 1 0,011 7 0,017 9 0,031 2 0,053 2 0,105 0,176 Nominal size d1(3,5) 4 5 6 (7) 8 Mass of shank per mm kg/1 0

22、00 units (7,85 kg/dm3) 0,075 5 0,098 6 0,154 0,222 0,302 0,394 Mass of head kg/1 000 units (7,85 kg/dm3) 0,294 0,426 0,799 1,438 2,262 3,352 The values of mass given in Table 3 are guideline values calculated on the basis of the relevant nominal size. Values of mass for other dimensions or lengths s

23、hall be calculated using Equation (1): ( ) fGlGG += KST(1) where GTis the mass, in kg/1 000 units; GSis the shank mass per mm, in kg/1 000 units; GKis the head mass, in kg/1 000 units; l is the shank length, in mm; f is the conversion factor for density and number of units (= 0,001 33mmdm). DIN 660:

24、2012-01 7 The head mass (steel) shall be calculated using Equation (2): =0001) 3(312KkrkG(2) where GKis the head mass, in kg/1 000 units; r1is the head radius, in mm; k is the head height, in mm; is the density, in kg/dm3(for steel 7,85 kg/dm3). The shank mass (steel) shall be calculated using Equat

25、ion (3): =0001mm1421SdG (3) where GSis the shank mass per mm, in kg/1 000 units; d1is the nominal diameter of the shank, in mm; is the density, in kg/dm3(for steel 7,85 kg/dm3). Intermediate sizes for d2and k shall be calculated using Equations (4) and (5). The results shall be rounded to the neares

26、t 0,5 mm. new11121new2dddd = (4) In Equation (4) d2newis the head diameter for intermediate sizes, in mm; d1newis the shank diameter for intermediate sizes, in mm; d11is the next highest shank diameter d1according to Table 1, in mm; d21is the next highest head diameter d2according to Table 1, in mm.

27、 DIN 660:2012-01 8 new111newddXk = (5) In Equation (5) knewis the head height for intermediate sizes, in mm; X is the next highest value of k, in mm; d1newis the shank diameter for intermediate sizes, in mm; d11is the next highest shank diameter d1according to Table 1, in mm. The tolerances specifie

28、d in this standard also apply to intermediate sizes. Dimension emaxis given by 0,5 d1new. Radius r1 is assumed to be approximately equal to 0,54 d2new. 4 Technical delivery conditions See Table 4. Table 4 Technical delivery conditions MaterialaSteel Nonferrous metal Stainless steel St = C4C or C10C,

29、 at the manufacturers discretion CuZn = CuZn37 Cu = Cu-DHP Al = EN AW-1050A Al 99,5 X3CrNiCu18-9-4 Standard DIN EN 10263-2 DIN EN 12166 DIN EN 12166 DIN EN 1301-2 DIN EN 10263-5 Dimensional and geometrical tolerances DIN 101 Surface finish Standard finish: bright Where a specific protective coating

30、is required (e.g. an electroplated coating complying with DIN EN ISO 4042), this shall be agreed when ordering. The tolerances and limit deviations specified in Table 1 also apply after coating. Testing of mechanical properties DIN 101 Heat treatment For steel: soft annealed (85 HV to 130 HV) or sub

31、ject to agreement. For other materials: subject to agreement. Acceptance inspection DIN 101 aOther materials shall be subject to agreement. DIN 660:2012-01 9 5 Designation Designation of a round head rivet with a nominal diameter d1= 4 mm and a length l = 20 mm, made of steel (St): Round head rivet

32、DIN 660 4 20 St 6 Application Table 5 specifies hole diameters and gives guideline values for upset head dimensions and maximum grip lengths of both round head (A) (see Figure 2) and countersunk head (B) (see Figure 3) rivets. The grip lengths specified in Table 5 are for guidance only. Trial riveti

33、ng is recommended, especially in the case of series production. Figure 2 Type A: upset head rounded Figure 3 Type B: upset head countersunk DI N 660: 2012 - 01 10 T ab l e 5 H o l e d i am et er s a n d g u i d e l i n e v a l u e s fo r u p s e t h e a d d i m e n s i o n s a n d g r i p l e n g th

34、 s D i m ens i ons in m illim e t r es d11 1, 2 ( 1, 4) 1, 6 2 2, 5 3 ( 3, 5) 4 5 6 (7 ) 8 d7H1 2 1, 05 1, 25 1, 45 1, 65 2, 1 0 2, 6 0 3, 1 0 3, 6 0 4, 2 0 5, 2 0 6, 3 0 7, 3 0 8, 4 0 R ound h ead ( A ) d8 1, 8 2, 1 2, 4 2, 8 3, 5 4, 4 5 ,2 6, 2 7, 0 8, 8 10, 5 12, 2 14, 0 k1 0, 6 0, 7 0, 8 1, 0 1,

35、 2 1, 5 1, 8 2, 1 2, 4 3, 0 3, 6 4, 2 4, 8 r1 1 ,0 1, 2 1, 4 1, 6 1, 9 2, 4 2, 8 3, 4 3, 8 4, 6 5, 7 6, 6 7, 5 C ount e r s unk h ead ( B ) d8 1, 8 2, 1 2, 4 2, 8 3, 5 4, 4 5, 2 6, 2 7 8, 8 10, 5 12, 2 14 ,0 k2 0, 4 0, 5 0, 6 0, 7 0, 8 1 ,0 1, 3 1, 4 1, 9 2, 4 2, 8 3, 3 3, 9 t10, 4 0, 5 0, 6 0, 7 0,

36、 8 1 ,0 1, 3 1, 4 1, 8 2, 3 2, 7 3, 2 3, 7 l M a x i m u m gr i p l engt h sm axA B A B A B A B A B A B A B A B A B A B A B A B A B 2 0, 5 1 0, 5 1 0, 5 1 1 1 3 1 2 1 2 1 2 0, 5 2 0, 5 1, 5 1 1 4 2 2, 5 2 2, 5 2 2, 5 1, 5 2, 5 1 2, 5 0, 5 2, 5 0, 5 2 2 1 5 2, 5 3, 5 2, 5 3, 5 2, 5 3, 5 2 3, 5 2 3 1,

37、 5 3 1, 5 3 0, 5 3 2 1, 5 6 3, 5 4, 5 3, 5 4, 5 3, 5 4, 5 3 4 2, 5 4 2 4 2 4 1, 5 4 1 3 2, 5 2 8 5 6 5 6 5 6 4, 5 5, 5 4 5, 5 4 5, 5 3, 5 5, 5 3 5 2 4, 5 0, 5 4 3, 5 3 10 7 7, 5 6, 5 7, 5 6 7, 5 6 7, 5 5, 5 7, 5 5 7, 5 4, 5 7 4 6, 5 2, 5 6 1, 5 5, 5 5 12 8 9, 5 7, 5 9 7, 5 9 7, 5 9 7 9 6 9 5, 5 8, 5

38、 4, 5 8 3, 5 7, 5 2, 5 7 14 9, 5 10, 5 9 10, 5 9, 5 10, 5 8, 5 10, 5 7, 5 10 7 10 6, 5 9, 5 5 9 4 8, 5 1 6 11 12 11 12 11 12 10 12 9 11 9 11, 5 8 11 7 11 6 10 18 12, 5 14 13 14 13 14 12 14 11 13 11 13 9, 5 13 9 13 8 12 20 14 15, 5 14 16 14 16 14 16 13 15 12 15 11 15 10 15 9, 5 14 22 16 18 16 18 16 1

39、8 15 17 14 17 13 17 12 16 11 15 25 18 20 18 20 18 20 17 19 17 19 16 19 15 19 14 18 DI N 660: 2012 - 01 11 T ab l e 5 ( c ont i n ued ) D i m ens i ons in m ill im e t r es d11 1, 2 ( 1, 4) 1, 6 2 2, 5 3 ( 3, 5) 4 5 6 (7 ) 8 d7H1 2 1, 05 1, 25 1, 45 1, 65 2, 1 0 2, 6 0 3, 1 0 3, 6 0 4, 2 0 5, 2 0 6,

40、3 0 7, 3 0 8, 4 0 R ound h ead ( A ) d8 1, 8 2, 1 2, 4 2, 8 3, 5 4, 4 5, 2 6, 2 7 ,0 8, 8 10, 5 12, 2 14 ,0 k1 0, 6 0, 7 0, 8 1 1, 2 1, 5 1, 8 2, 1 2, 4 3, 0 3, 6 4, 2 4, 8 r1 1, 0 1, 2 1, 4 1, 6 1, 9 2, 4 2, 8 3, 4 3, 8 4, 6 5, 7 6, 6 7, 5 C ount e r s unk h ead ( B ) d8 1, 8 2, 1 2, 4 2, 8 3, 5 4,

41、 4 5, 2 6, 2 7, 0 8, 8 10, 5 12, 2 14, 0 k2 0, 4 0, 5 0, 6 0, 7 0, 8 1, 0 1, 3 1, 4 1, 9 2, 4 2, 8 3, 3 3, 9 t10, 4 0, 5 0, 6 0, 7 0, 8 1, 0 1, 3 1, 4 1, 8 2, 3 2, 7 3, 2 3, 7 l M a x i m u m gr i p l engt h sm axA B A B A B A B A B A B A B A B A B A B A B A B A B 28 21 23 21 23 20 22 19 22 18 22 17

42、 22 16 21 30 23 25 23 25 22 24 21 24 20 23 19 23 18 22 32 24 27 23 26 23 26 22 25 21 25 20 24 35 27 29 26 28 25 28 24 28 24 28 22 27 38 30 32 29 31 28 31 27 30 26 30 25 29 40 31 34 30 32 30 32 28 32 28 32 27 31 DIN 660:2012-01 12 Bibliography DIN EN 10263-1, Steel rod, bars and wire for cold heading and cold extrusion Part 1: General technical delivery conditions