DIN 6624-1-1989 Horizontal single-wall steel tanks with capacities between 1000 and 5000 litres for the above ground storage of flammable and non-flammable water polluting liquids《.pdf

1、UDC 621.642.39.038-034.14 DEUTSCHE NORM September 1989 Dimensions in mm 1 Scope and field of application This standard specifies horizontal single-wall steel tanks that are used for the above ground storage of flammable and non-flammable water polluting liquids. Such tanks may be provided with a pro

2、tective lining which has been type approved under article 12 of the Verordnung ber brennbare Flssigkeiten (German Regulation on Flammable Liquids) or been granted a test mark under the building regulations. They are suitable for storing liquids with a maximum density of 1,9 kg/l and may be used at a

3、 working pressure of up to 0,5 bar. Tanks as covered here shall be installed in a catchpit. Excepted from this requirement are single-wall tanks with no connections below the permissible filling height, that are used for the storageof non-flammable liquidsof WGKO*)orof WGKl*), provided thetanks in t

4、he latter case are tested every five years by an expert as defined in the Verordnung ber Lagern, Abfllen und Umschlagen wassergefhrdender Stoffe (German Regulation on the Storage, Filling and Han- dling of Water Polluting Substances). This standard shall be used in conjunction with DIN 6600, taking

5、into account the requirements specified in DIN 6601 *). *) WGK = Wassergefhrdungsklasse (Water pollution class). These classes are listed in a water polluting substances catalogue kept at the Umweltbundesamt (German Federal Office for the Environment), Bismarckplatz 1, 0-loo0 Berlin 33. *) At presen

6、t at the stage of draft. Page 2 DIN 6624 Part 1 2 Dimensions and designation Any design details not specified here are at the manufacturers discretion. Type A: Tank supports, manhole and manhole cover selected for tanks designed for the storage of hazardous flammable liquids of class AI, All and B a

7、s specified in the Verordnung ber brennbare Flssigkeiten and of non-flammable liquids. B !- Surface Section A-A section B-B roughness of facing: /P - a620 J 28 bolts, thread size M 16 0 5Bo $18 o See DIN 608 Part 1 for manhole and manhole cover dimensions. t A- DIN 6624 Part 1 Page 3 Tank capacity,

8、in m3 Outside diameter, d Type B: Tanksupportsandmanholeselected fortanksdesignedforthestorageof hazardousflammableliquidsof class AIIIasspecified in the Verordnung ber brennbare Flssigkeiten and that have to be moved about on site. Entry opening (manhole cover design at the manufacturers discretion

9、) 1 13 2 3 3,5 5 1 O00 1250 I Leg support Minimum clearance, h Approximate mass, in kg Minimum support width, 6 Leg width, c Support centre-line distance, a Wooden runner 90 f 20 165 210 260 355 350 560 130 240 90 200 I 720 1220 1580 2700 1800 2620 / Support design at the manufacturers discretion De

10、signation of a type A horizontal single-wall tank with a capacity of 2000 litres and an outside diameter of 1000 mm: Tank DIN 6624 - 2000 X 1000 - A Table 1. Tank capacity, dimensions and mass Approximate tank length, I I 1450 I 2100 I 2750 1 4050 1 3100 1 4350 Nominal plate thickness), s I 3 Maximu

11、m radius of curvature, I, I 1 O00 I 1250 Minimum crown radius, r2 I 33 I 42 Inside diameter of manhole I 500 Tanks with capacities of 2000 and 3000 litres may also be assigned to an outside diameter of 1250 mm, in which case the tank length, L, shall be approximately 21 O0 mm and 2900 mm, respective

12、ly. Page 4 DIN 6624 Part 1 3 Materials Steel grades St 37-2, USt 37-2, RSt 37-2 St 37-3, St 44-2, St 44-3, St 52-3 HI, HI1 17Mn4 DIN 17 100 steels DIN 17 155 steels 1 Type of materials testing certificate as in DIN 50 049 Test report Inspection certificate B Inspection certificate B Inspection certi

13、ficate A 3.6 or 4.6 Bolts as in IS0 898 Part 1 DIN 17 440 or DIN 17 441 stainless austenitic steels 1.4301, 1.4306, 1.4541, 1.4571 - I Inspection certificate B Other steels may be used if their suitability has been attested to by an expert. 4 Construction Tanks shall be butt welded on both sides or

14、welded on stiffeners. Weldsshall be made using suitable equipment and welding filler metals. Preparation of components to be welded shall besuch that high-quality welding is ensured and so as to minimize residual welding stresses. Manufacturing tanks requires written verification of the processes us

15、ed, so as to guarantee the consistent quality of the tanks supplied. Before work begins, tank manufacturers shall have their welding facilities inspected by an expert as defined in paragraph 1, article 16 of the Verordnung berbrennbare Flssigkeiten, such inspection being undertaken in the form of we

16、lding procedure testing as specified in subclause 2.22 of both Technische Regeln fr brennbare Flssigkeiten (Technical rules on flammable liquids) (TRbF) 121 and 221. Welding procedure testing is also required for tanks designed for the storage of non- flammable liquids. If automatic welding is used,

17、 welding one side as opposed to both shall be permitted, provided the welding quality, in a welding procedure test, has been attested to by an expert as defined above. Filler metals shall be compatible with the tank material and provide a tough weld metal. Manual welding shall only be performed by q

18、ualified welders who have undergone approval testing as specified in DIN 8560 (this shall be test group B I for welding St 37 steel). Any protective coatings (e.g. priming or galvanizing) shall be the subject of agreement. The manhole cover shall be provided with a G 1 threaded connection (thread si

19、ze in accordance with IS0 228 Part 1) or another suitable connection, to permit attachment of the level limiter integral with the tank wagons device to prevent overfilling of the tank. If lifting lugs are provided (cf. DIN 6608 Part l), these shall be capable of lifting the empty tank. Thecontactfac

20、es between tankandsupportsshall beselectedtoensure thatwhen thetankisful1,asurfacepressureof 15 N/cm* is not exceeded. 5 Leak detection system Tanks that are not installed in a catchpit shall be lined to prevent leakage as far as possible and be provided with a leak indicating device. Both the linin

21、g and the device shall have been type approved under article 12 of the Verordnung ber brennbare Flssigkeiten or been granted a test mark under the building regulations. 6 Testing Tanks shall be type tested for compliance with the requirements specified in this standard. In addition, upon completion

22、of all welding operations, each tankshall be tested for soundness with water at a pressure of at least2 bar. Tanks which have passed the test shall be issued a test certificate stating all test results and the tank material. 7 Marking Tanks complying with this standard shall bear a durable nameplate

23、 providing the following information, to be attached to a fixture on the tank shell near the manhole or one tank end: DIN 6624 Part 1 Page 5 manufacturers name or trademark; manufacturers reference number; year of manufacture: tank capacity, in litres; test pressure: 2 bar; DIN 6624 A (or B)/DIN 660

24、1; material. Inspection DIN 6600 shall apply for the inspection of tanks. Standards and other documents referred to DIN 1541 DIN 1543 DIN 6600 DIN 6601 DIN 6608Part1 DIN 8560 DIN 17 100 DIN 17 155 DIN 17 440 DIN 17 441 DIN 50 O49 IS0 228 Part 1 IS0 898 Part 1 Steel flat products; cold rolled wide mi

25、ll strip and sheet of unalloyed steels; dimensions, limit deviations and form tolerances Steel flat products; hot rolled plate 3 to 150 mm thick; dimensions, limit deviations and form tolerances Steel tanks for the storage of flammable and non-flammable water polluting liquids; concepts and inspecti

26、on (at present at the stage of draft) Steel tanks for the storage of flammable and non-flammable water polluting liquids; compatibility of stored liquid and tank material Horizontal single-wall steel tanks for the underground storage of flammable and non-flammable water polluting liquids Qualificati

27、on testing of welders for welding steel Steels for general structural purposes; quality standard Steel sheet and strip with elevated temperature properties; technical delivery conditions Stainless steels: technical delivery conditions for sheet, hot rolled strip, wire rod, drawn wire, steel bars, fo

28、rgings and semi-finished products Stainless steels; technical delivery conditions for cold rolled strip and slit strip and for plate and sheet cut therefrom Materials testing certificates Pipe threads where pressure-tight joints are not made on the threads; designation, dimensions and tolerances Mec

29、hanical properties of fasteners; bolts, screws and studs Verordnung ber brennbare Flssigkeiten *) Verordnung ber Lagern, Abfllen und Umschlagen wassergefhrdender Stoffe*) TRbF 121 *) TRbF 221*) Ortsfeste Tanks aus metallischen Werkstoffen (stationary metal tanks for the storage of hazardous flammabl

30、e liquids of other than class A III) Ortsfeste Tanks aus metallischen Werkstoffen (Stationary metal tanks for the storage of hazardous flammable liquids of class A III) Previous editions DIN 6624: 08.66,04.67,07.68; DIN 6624 Part 1 : 10.81. Amendments The following amendments have been made to the O

31、ctober 1981 edition. a) The scope has been extended to include non-flammable water polluting liquids as covered in DIN 6601. b) The standard designation now includes a letter symbol. c) Specifications regarding tanks for the storage of liquids of other than class A III have been added. International Patent Classification B 65 D 88/02 B 65 D 90102 6 65 D 90/50 G O1 M 3/00 *) Obtainable from Deutsches Informationszentrum fr Technische Regeln of DIN, Burggrafenstrae 6, 0-1000 Berlin 30.