DIN EN 12243-1999 Touch and close fasteners - Determination of dimensional change in washing and drying and dry cleaning German version EN 12243 1999《接触锁扣 洗、干燥和干洗中尺寸变化的测定》.pdf

1、DEUTSCHE NORM December 1999 I DIN Touch and close fasteners Determination of dimensional change in washing and drying - I EN 12243 and dry cleaning English version of DIN EN 12243 ICs 61 .O40 Haftverschlsse - Bestimmung der Manderung beim Waschen und Trocknen und Chemischreinigen Supersedes parts Ju

2、ne 1990 edition, withdrawn in January 1997. of DIN 3415-2, European Standard EN 12243 : 1999 has the status of a DIN Standard. A comma is used as the decimal marker. National foreword This standard has been prepared by CEN/TC 248. The responsible German body involved in its preparation was the Norme

3、nausschuss Textil und Textil- maschinen (Textile and Textile Machinery Standards Committee), Technical Committee Textile Haftver- schlsse. Amendments Parts of DIN 341 5-2, June 1990 edition, have been superseded by the specifications of DIN EN 12243. Previous edition DIN 341 5-2: 1990-06. EN compris

4、es 5 pages. No pari of this standard may be reproduced without the prior permission of Y Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany, s the exclusive right of sale for German Standards (DIN-Normen). Ref. No. DIN EN 12243 : 1999-1 English price group 05 Sales

5、 No. 1105 05.00 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12243 October 1999 ICs 61 .O40 English version Touch and close fasteners Determination of dimensional change in washing and drying and dry clean ing Fermetures auto-agrippantes - Dtermination du changement dimensionnel lors du lava

6、ge et du schage ou lors du nettoyage sec Haftverschlsse - Bestimmung der Manderung beim Waschen und Trocknen und Chemischreinigen This European Standard was approved by CEN on 1999-09-05. CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for givi

7、ng this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national stand- ards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official vers

8、ions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium,

9、the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central

10、Secretariat: rue de Stassart 36, B-1050 Brussels O 1999. CEN - All rights of exploitation in any form and by any means reserved worldwide for CEN national members. Ref. No. EN 12243 : 1999 E Page 2 EN 12243 : 1999 Foreword This European Standard has been prepared by Technical Committee CENTC 248 “Te

11、xtiles and textile products“, the secretariat of which is held by BSL This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2000, and conflicting national standards shall be withdrawn at the lates

12、t by April 2000. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece. Iceland, Ireland, Italy, Luxembourg, Netherla

13、nds, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. It is one of a series of standards for touch and close fasteners. Other standards in the series are as follows: EN 1414 Touch and close fasteners - Cycling procedures for subsequent testing. EN 1415 Touch and close fasteners -

14、 Behaviour of slit selvedges. EN 1416 Touch and close fasteners - Determination of curvature. EN 12240 Touch and close fasteners - Determination of the overall effective width of tapes and the effective width of a closure. EN 12241: 1999 Touch and close fasteners - Method for closure prior to washin

15、g or dry cleaning. EN 12242: 1999 Touch and close fasteners - Determination of peel strength. EN XXXX ) Touch and close fasteners - Determination of longitudinal shear strength. EN XXXX ) Touch and close fasteners - Determination of vertical tension strength. EN XXXX ) Touch and close fasteners - Re

16、sistance to fraying of tapes after cutting EN XXXX ) Touch and close fasteners - Specifications. ) In preparation Page 3 EN 12243 : 1999 1 Scope This European Standard specifies a method for determining the dimensional change in washing and drying or dry cleaning of touch and close fastener tapes. 2

17、 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisio

18、ns of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 20 139 Textiles - Standard atmospheres for conditioning and testing (IS0 139: 1973). EN 12241 :

19、1999 Touch and close fasteners - Method of closure prior to washing and drying or dry-cleaning. EN IS0 3175 Textiles - Evaluation of stability to machine dry- cleaning (IS0 3175: 1995) EN 26330 Textiles - Domestic washing and drying procedures for textile testing (IS0 6330: 1984) 3 Principle The per

20、centage change is determined in the length of touch and close fastener tapes after washing and drying or dry cleaning. 4 Apparatus 4.1 Rule marked in millimetres and longer than the greatest dimension being measured. 4.2 Equipment for marking precise reference points (e.g. indelible ink, threads, st

21、aples). 5 Test specimens Take three male and three female tapes each of a minimum length 500 mm. Page 4 EN 12243 : 1999 6 Conditioning Condition the test specimens for a minimum of 24h in accordance with the standard temperate atmosphere for testing as specified in EN 201 39. 7 Procedure 7.1 Marking

22、 Place each test specimen flat on the measuring surface and make a pair of marks on it at least 250mm apart in the length direction. Do not mark within 25mm of each end. 7.2 Measuring original length After the test specimens have been conditioned in accordance with clause 6, determine the original l

23、ength as follows. Place the test specimens with the pile facing down on a flat surface and remove any wrinkles without stretching the test specimen. Place the rule on the test specimen and record the distance between the pair of marks to an accuracy of at least Imm. 7.3 Washing and drying Close the

24、tapes in accordance with EN 12241: 1999, wash and dry them for the specified number of times in accordance with the procedure specified in EN 26330. 7.4 Dry cleaning Close the tapes in accordance with EN 12241 and dry clean the closed specimens for the specified number of times in accordance with th

25、e procedure specified in EN IS0 3175. 7.5 Measuring final length Open the test specimens, re-condition and measure the final length as follows: Place the test specimens with the pile facing down on a flat surface and remove any wrinkles without stretching the test specimen. Place the rule on the tes

26、t specimen and record the distance between the pair of marks to an accuracy of at least Imm. Page 5 EN 12243: 1999 8 Calculation and expression of results Calculate, for each test specimen, the change in dimension for the length direction (in percent) as follows: Calculate the mean dimensional chang

27、e for the length direction and express it to the nearest 0,5%. Indicate if the dimension has decreased (shrinkage) by means of a minus sign (-) or increased (extension) by means of a plus sign (+). 9 Test report Report the following information: a) number and date of this European Standard; b) date of the test; c) identification of the touch and close fastener tape; d) the result obtained and expressed as in clause 8; e) whether the fastener stayed closed or opened during the washing procedure; f) any deviation from this standard and any incident likely to have affected the results.