DIN EN ISO 148-1 Bb 1-2014 Metallic materials - Charpy pendulum impact test - Part 1 Test method Supplement 1 Special test pieces《金属材料 悬臂冲击试验 第1部分 试验方法 补充件1 特殊试样》.pdf

1、February 2014 Translation by DIN-Sprachendienst.English price group 5No part of this translation may be reproduced without prior permission ofDIN Deutsches Institut fr Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).IC

2、S 77.040.10!%+)“2089906www.din.deDThis supplement provides information relating to DIN EN ISO 148-1, but does not contain any additional specifications.DIN EN ISO 148-1 Supplement 1Metallic materials Charpy pendulum impact test Part 1: Test method; Supplement 1: Special test pieces,English translati

3、on of DIN EN ISO 148-1 Beiblatt 1:2014-02Metallische Werkstoffe Kerbschlagbiegeversuch nach Charpy Teil 1: Prfverfahren; Beiblatt 1: Sonderprobenformen,Englische bersetzung von DIN EN ISO 148-1 Beiblatt 1:2014-02Matriaux mtalliques Essai de flexion par choc sur prouvette Charpy Partie 1: Mthode dess

4、ai; Supplment 1: Formes des prouvettes particulaires,Traduction anglaise de DIN EN ISO 148-1 Beiblatt 1:2014-02Partially supersedesDIN 50115:1991-04www.beuth.deDocument comprises 6 pagesIn case of doubt, the German-language original shall be considered authoritative.03.14 DIN EN ISO 148-1 Suppl. 1:2

5、014-02 2 A comma is used as the decimal marker. Contents Page Foreword . 3 1 Scope . 4 2 Test pieces 4 Bibliography . 6 DIN EN ISO 148-1 Suppl. 1:2014-02 3 Foreword This document (DIN EN ISO 148-1 Supplement 1:2014-02) has been prepared by the Normenausschuss Materialprfung (Materials Testing Standa

6、rds Committee), Working Committee NA 062-01-44 AA Schlagzhigkeitsprfung fr Metalle. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. DIN shall not be held responsible for identifying any or all such patent rights. DIN 50115 has bee

7、n partially replaced by DIN EN ISO 148-1, which has integrated the determination of lateral expansion and per cent shear fracture (dull). The responsible German body, Working Group NA 062-01-44 AA, decided to publish the remaining technical information specified in DIN 50115 and not yet included in

8、DIN EN ISO 148-1 or DIN EN ISO 14556 as a Supplement to DIN EN ISO 148-1, and not as a residual standard. The standard DIN EN ISO 148-1 specifies general information on test pieces. This document does not stipulate the use of specific test pieces, but is intended to give the user an informative over

9、view. Amendments This standard differs from DIN 50115:1991-04 as follows: a) specific test pieces are no longer stipulated, but included as an informative overview; b) only the special test pieces DVM and DVMK are included; c) the determination of lateral expansion is dealt with in DIN EN ISO 148-1;

10、 d) the determination of the per cent shear fracture (dull) is dealt with in DIN EN ISO 148-1; e) the standard has been editorially revised. Previous editions DIN DVM A 115 = DIN 50115: 1937-09 DIN 50115: 1952x-05, 1966-11, 1975-02, 1991-04 DIN EN ISO 148-1 Suppl. 1:2014-02 4 1 Scope This Supplement

11、 covers test pieces which are not specified in DIN EN ISO 148-1 and DIN EN ISO 14556, but which have hitherto been specified in DIN 50115. 2 Test pieces Test piece types and dimensions are shown in Figures 1 to 3 and Table 1, respectively. Dimensions in millimetres Key w Width of test piece l Length

12、 of test piece h Height of test piece h1Height below notch 1 Test cross-section S Figure 1 Test piece dimensions (notation) Dimensions in millimetres aU-notch (milled) bKeyhole notch Figure 2 DVM test piece DIN EN ISO 148-1 Suppl. 1:2014-02 5 Dimensions in millimetres Figure 3 DVMK test piece Table

13、1 Test piece dimensions Test piece type Figure No. Length Width Height Height below notch Area under test, in cm2Radius at base of notch Angle of notch, in Distance between supports Designation Symbol DVM test piece DVM 2 55 1 10 0,1 10 0,1 7 0,1 0,70 1 0,05 02,040+DVMK test piece DVMK 3 44 1 6 0,1

14、6 0,1 4 0,1 0,24 0,75 0,05 05,030+All test pieces shall be rectangular, the angle between adjacent faces being 90 2. DIN EN ISO 148-1 Suppl. 1:2014-02 6 Bibliography DIN EN ISO 148-1, Metallic materials Charpy pendulum impact test Part 1: Test method DIN EN ISO 1302, Geometrical Product Specificatio

15、ns (GPS) Indication of surface texture in technical product documentation DIN EN ISO 14556, Steel Charpy V-notch pendulum impact test Instrumented test method SEP 1315, Kerbschlagbiegeversuch mit Ermittlung von Kraft und Weg Empfehlungen zur Durchfhrung und Auswertung (Notched bar impact testing including determination of force/extension characteristics; testing and evaluation) (withdrawn) ASTM A 370, Standard Test Methods and Definitions for Mechanical Testing of Steel Products