DLA A-A-50016 B-2001 GLOVES MEN-S CLOTH LEATHER PALM KNITTED WRISTLET SIZE MEDIUM《中号针织腕带 皮革手掌的男式布手套》.pdf

1、 INCH/POUNDA-A-50016BMAY 18, 2001SUPERSEDINGA-A-50016AJAN. 8, 1990COMMERCIAL ITEM DESCRIPTIONGLOVES, MENS; CLOTH, LEATHER PALM, KNITTED WRISTLET, SIZE MEDIUMThe General Services Administration has authorized the use ofthis commercial item description as a replacement for Type II,Class 1 of JJ-G-451.

2、1. SCOPE. This document covers medium size mens gloves.2. SALIENT CHARACTERISTICS2.1 Description. The gloves will utilize the Gunn pattern, witha leather palm and knitted wristlet.2.2 Material.2.2.1 Leather. The leather for the palm, the front of fingers,the front and back of the thumb, the back of

3、the finger tips andprotective welt for seam joining front of fingers (fourchettes)to the palm will be chrome tanned, flesh split from cattlehidebends. Middle splits, head splits, belly splits and shouldersplits will not be used. All leather parts, except the welt,shall be 2-1/2 to 3-1/2 ounces thick

4、 when tested as specified inASTM-D-1814. (Note: One ounce is equivalent to 1/64 inch). Thewelt will be 1-1/2 to 2-1/2 ounces thick when tested as specifiedin ASTM-D-1814.Beneficial comments, recommendations, additions, deletions,clarifications, etc. and any data which may improve this documentshould

5、 be sent to: Defense Supply Center Philadelphia, Clothingand Textiles Directorate, Attn: DPSC-COCT, 700 Robbins Avenue,Philadelphia, PA 19111-5092.AMSC N/A FSC 8415Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50016B22.2.2 Cloth. The back of th

6、e glove will be a napped cottoncanton flannel, minimum weight 7.0 ounces per square yard whentested as specified in ASTM-D-3776, with the napped surfacefacing the hand. The palm, front of the fingers, and front ofthe thumb will be lined with cotton flannel, minimum weight 5.0ounces per square yard w

7、hen tested as specified in ASTM-D-3776.The napped surface of the lining will face the hand. The knittedcotton wristlet will bea1by1ribknit seamless tubingweighing from 9 to 15 yards per pound when tested as specified inASTM-D-3776, 2-3/4 inches wide at the open end, and a minimum of2-1/2 inches long

8、 from the seam attachment.2.3 Dimensions. The finished gloves will conform to themeasurements specified below. Any variation on the same pair ofmore than 1/4 inch for any dimension will be scored as a defect.Location Inches Tolerance (inch)A. Overall length, tip of 2nd(middle) finger to top of cuff.

9、 10-1/4 + 1/2B. Hand length; tip of 2nd (middle) 7-1/2 + 1/4finger to wrist seamC. Width of glove across palm from 5-1/4 + 1/4base of the thumb._2.4 Labels. A commercial-type label is acceptable, provided thatan additional printed cloth label containing the contractorsname, contract number, size and

10、 National Stock Number (NSN) iscaught on the stitching of the commercial label. The commerciallabel will include fiber and laundering information.2.4.1 Label/tag. Each item will be individually bar-coded with apaper tag for personal clothing items. The paper tag will bestandard bleached sulfate havi

11、ng a basis weight of 100 pounds.The paper used for the tags will have a smooth finish to acceptthermal transfer and direct printing. The tags will have a holeand will be attached to each item by a fastener, clearly legibleand readable by a scanner. The bar coding element will be a 13digit national s

12、tock number (NSN). The bar code type will be amedium to high code density and will be located so that it iscompletely visible on the item when it is folded and/or packagedas specified and so that it causes no damage to the item.Provided by IHSNot for ResaleNo reproduction or networking permitted wit

13、hout license from IHS-,-,-A-A-50016B33. REGULATORY REQUIREMENTS. Recycled, recovered, orenvironmentally preferable materials should be used to themaximum extent possible provided that the material meets orexceeds the operational and maintenance requirements, andpromotes economically advantageous lif

14、e cycle costs.4. QUALITY ASSURANCE PROVISIONS4.1 Product conformance. The products provided will meet thesalient characteristics of this commercial item description andwill conform to the producers own drawings, specifications,standards, and quality assurance practices. The Governmentreserves the ri

15、ght to require proof of such conformance.4.2 Examination. Each glove will be inspected for visual anddimensional attributes in accordance with ANSI/ASQC Z1.4 -Sampling Procedures and Tables for Inspection by Attributes,published by the American Society for Quality Control. The lotsize will be expres

16、sed in units of one glove. The sample unitwill be one glove and the selection will be by pairs.4.2.1 Visual examination. Each glove will be examined for thedefects listed below:Any hole, cut, or tear; color not as specified; any part shaded;any spot or stain (outside); raw edges, open seams, thread

17、endsnot removed, or loose tension resulting in loose seams; anymaterial defects, distorted parts or poor workmanship; anycomponent part omitted; label missing, incorrect, or illegible;measurement of item not as specified; bar code omitted or notreadable by scanner; human-readable interpretation (HRI

18、) omittedor illegible; bar code not visible on folded, packaged item; barcode causes damage to the item; any items not packaged inaccordance with the contract or purchase order. (Up to 3 needleholes are acceptable).4.2.2 Dimensional examination. The gloves will be measured foroverall length, hand le

19、ngth and hand width for conformance to thedimensions listed in 2.3.4.3 Acceptance criteria. Acceptance criteria will be as specifiedin the contract or purchase order.5. PACKAGING. The preservation, packing, and marking will be asspecified in the contract or order.Provided by IHSNot for ResaleNo repr

20、oduction or networking permitted without license from IHS-,-,-A-A-50016B46. NOTES6.1 Source of Government documents. Copies of military andFederal documents are available from:Standardization Documents Order DeskBldg. 4D700 Robbins AvenuePhiladelphia, PA 19111-50946.2 Source of non-Government docume

21、ntsANSI/ASQC Z1.4 - Sampling Procedures and Tables ForInspection By Attributes(Applications for copies should be addressed to AmericanNational Standards Institute, 1430 Broadway, New York, NY 10018-3308).MILITARY INTERESTS:Custodians CIVIL AGENCY COORDINATINGArmy - GL ACTIVITY:GSA - FSSReview Activi

22、ties JUS - FPIArmy - MD USDA - AFSPREPARING ACTIVITY:DLA-CTProject 8415-0199Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50016B5STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSALINSTRUCTIONS1. The preparing activity must complete blocks 1, 2, 3, an

23、d 8. In block 1, boththe document number and revision letter should be given.2. The submitter of this form must complete blocks 4, 5, 6, and 7 and send topreparing activity.3. The preparing activity must provide a reply within 30 days from receipt of theform.NOTE: This form may not be used to reques

24、t copies of documents, nor to requestwaivers, or clarification of requirements on current contracts. Comments submitted onthis form do not constitute or imply authorization to waive any portion of thereferenced document(s) or to amend contractual requirements.I RECOMMEND A CHANGE:1. DOCUMENT NUMBERA

25、-A-55016B2. DOCUMENT DATE (YYYYMMDD)2001/MAY 183. DOCUMENT TITLEGLOVES, MENS; CLOTH, LEATHER PALM, KNITTED WRISTLET, SIZE MEDIUM4. NATURE OF CHANGE (Identify paragraph number and include proposed rewrite, if possible. Attach extra sheetsas needed.)5. REASON FOR RECOMMENDATION6. SUBMITTERa. NAME (Las

26、t, First, Middle Initial) b. ORGANIZATIONc. ADDRESS (Include Zip Code) d. TELEPHONE (Include Area Code)(1) Commercial(2) DSN(If applicable)7. DATESUBMITTED(YYYYMMDD)8. PREPARING ACTIVITYa. NAMEDEFENSE SUPPLY CENTER PHILADELPHIADSCP-COCTb. TELEPHONE (Include Area Code)(1) Commercial (2)DSN-444-2426(2

27、15) 737-2426c. ADDRESS (Include Zip Code)700 Robbins Ave (Bldg 6, C&T)PHILADELPHIA, PA 19111-5092IF YOU DO NOT RECEIVE A REPLY WITHIN 45 DAYS, CONTACT:Defense Standardization Program Office (DLSC-LM)8725 John J. Kingman Road, Suite 2533Fort Belvoir, Virginia 22060-6221Telephone (703) 767-6888 DSN 427-6888DD Form 1426, FEB 1999 (EG) PREVIOUS EDITION ISOBSOLETE WHS/DIOR, Feb 99Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-