DLA A-A-50106 B-2000 STOPPER WIRED WEDGED《楔形带线的塞子》.pdf

1、W 90L8054 000571 730 a Size I II III I INCH-POUND I A-A-50106B February 24,2000 SUPERSEDING February 21,1990 A-A-50106A Stopper Stopper Wire Min. breaking Total Height, inches Width, inches Diameter, inches Strength Weight 0.335 f 0.020 0.170 _+ 0.020 0.0625 + 0.010 772 lbs. 0.3 oz. 0.400 _+ 0.020 0

2、.195 _+ 0.020 0.0625 + 0.010 772 lbs. 0.4 oz. 0.475 2 0.020 0.283 _+ 0.020 0.0930 + 0.012 1433 lbs. 0.8 oz. - 0.000 - 0.000 - 0.000 COMMERCIAL ITEM DESCRIPTION STOPPER, WIRED, WEDGED The General Services Administration has authorized the use of this Commercial Item Description for all Federal agenci

3、es. 1. SCOPE. This commercial item description covers the requirement for wired stoppers to be used to provide security for personnel and equipment in operations invoking steep ascents by placing the wired stoppers into cracks in rocks. 2. CLASSIFICATION. The wired stoppers shall be furnished in the

4、 following sizes as specifed: Table I. Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document should be sent to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DSCP-COET, 700 Robbins Ave, Philadelphia,

5、 PA 19111-5096. AMSC NIA FSC 8465 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-W 9018054 0005719 b77 IV V VI VI1 A-A-50106B Height, inches Width, inches Diameter, inches Strength Weight 0.520 _+ 0.020 0.330 _+ 0.020 0.0930 i- 0.012 1433 Ibs. 1.14

6、oz. 0.650 _+ 0.020 0.460 i 0.020 O. 1250 + 0.014 2425 lbs. 1.42 oz 0.750 _+ 0.020 0.530 _+ 0.020 0.1250 i- 0.014 2425 lbs. 1.82 oz. - 0.000 - 0.000 - 0.000 0.855 _+ 0.020 0.600 _+ 0.020 0.1250 $. 0.014 2425 lbs. 2.21 oz. Table I. (contd) VI11 - 0.000 - 0.000 1.250 2 0.020 0.900 2 0.020 0.1250 + 0.01

7、4 24251bs. 3.39 oz. 3. SALIENT CHARACTERISTICS. 3.1 Design and construction The wedged shaped stopper portion of the wired stopper shall be 6061 - T6 or 7075 aluminurn for sizes I, II, and III. The wedged shaped stopper portion of the wired stopper sizes IV through VI11 shall be 6061 - T6 aluminum.

8、The wired portion and wire loop cable shall be either galvanized steel or stainless steel. The wire loop cable shall protrude 7.5 2 0.500 inches below the bottom of the stopper head. The wired stopper shall be constructed and comply with the requirements in table I (see figure I). 3.1.1 ms. The wire

9、d stoppers shall be pull tested by sliding the stopper to the center of the wire there by exposing the looped ends of the wire. The two looped ends shall be placed over two steel dowels approximately 318 inches in diameter and pull tested to 60 percent of the wires minimum breaking strength (see tab

10、le I). Any breaks in the wire strands, slippage of wires through the swage, or permanent deformation shall constitute failure of the test, and rejection of the unit on which the failure occurred. One unit out of every 100 shall be pulled for this requirement. This test is to be performed at room tem

11、perature. Any industrial testing machine may be used to determine compliance with this requirement. 4. REGULATORY REOUIREMENTS. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation

12、 (FAR). 5. QUALITY ASSURANCE PROVISIONS. 5.1 Product conformance. The products provided shall meet the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, standards, and quality assurance practices, and to be the same product 2 Provided

13、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-offered for sale in the commercial market. The government reserves the right to require proof of such conformance. 5.2 Visual examination Each item shall be examined for the defects listed below. Defects. Finis

14、h not smooth and adherent; not free of burrs, rough spots, sharp edges, slivers, flat areas or projections; any component missing or not specified type; any component fractured, split, dented, bowed, malformed, damaged or loose; signs of strand breakage unusual wear or kinks; bends are not smooth an

15、d continuous; markings in wrong locations, incomplete, illegible, or not as specified. 5.3 Dimensional examination The wired wedged stoppers shall be examined without damaging or disassembling the item. Any dimension not within the specified tolerances shall be classified as a defect. 5.4 Acceptance

16、 criteria. Acceptance criteria shall be as specified in the contract or purchase order. 6. PACKAGING. 6.1 Preservation, packing, and marking. The preservation, packing, and marking shall be as specified in the contract or order. 7. NOTES 7.1 Source of Govenunent documents. Copies of military and Fed

17、eral documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19 1 1 1-5094 7.2 Products known to meet this CID. Below is only a sampling of known suppliers and not an all-inclusive list. 1. Adventure Tech, Inc 4124 N. Burns Road Spokane, WA 992

18、16 2. Climb High 1861 Shelburne Road Shelburne, Vermont 05482 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL I TARY INTERESTS : custodians Army - GL Navy - NU Air Force - 99 Review Activities Air Force - 1 1.6 Navy - MC CIVIL AGENCY COORDINATING ACTIVITY GSA - FSS PREPARING ACTIVITY: DLA-CT Project Number 8465-0297 Stopper, Wired, Wedged Figure I 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-