DLA A-A-50355 B-1992 GLOVES MEN-S AND WOMEN-S CLOTH VINYL COATED《塑料覆盖男式和女式的衣物手套》.pdf

1、A-A-50355B 17 JULY 1992 SUPERSEDING 10 APRIL 1989 A-A-50355A COMMERCIAL ITEM DESCRIPTION GLOVES, MENS AND WOMENS CLOTH, VINYL COATED The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-G-29114. Salient Characteristics. The gloves are to

2、 be used by ammunition and pyrotechnic material handlers. The gloves shall be constructed from a two piece cut and sew process, or fully fashioned from plain or jersey knit fabric, 100% cotton and polyvinyl chloride dipped. All seams shall be to the inside of the glove. Seam allowances shall be mini

3、mum. The coating compound will cover the entire outside surface of the glove and be suitably compounded to provide a good gripping surface, and abrasion resistance for the finished glove. The gloves shall be furnished in medium and large sizes for both men and women. The color of the finished glove

4、shall be tan/yellow. The gloves shall be paired by a commercially accepted method. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directo

5、rate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited

6、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-503558 84 m 9999974 0081237 Ob4 m A-A-50355B Material. The gloves shall be manufactured from plain or jersey knit fabric, 100% cotton, natural color. Sizes. The gloves shall be provided in the foll

7、owing sizes: Men s Medium Large Women s Medium Large NOTE: The gloves are ordered by size, therefore the sizes medium and large may be abbreviated as MED and LG. Label/markinq. In addition to any commercial markings, each glove shall be legibly stamped. The stamp shall be located on the outside of t

8、he glove containing the contractors name, contract number, size, NSN and fiber content. Patterns. Patterns will be developed by the contractor to meet the specified finished requirements. Abrasion Resistance. The finished gloves shall show no evidence of break thru on the coated fabric after the sur

9、face is abraded 500 cycles when tested in accordance with FED-STD-191, Test Method 5306 with a 1000 gr weight on each H-18 Wheel. The test shall be conducted on the coated side of the cloth and the evaluation performed from uncoated side. Sizes and Measurements. The finished gloves shall conform to

10、the measurements below (in inches): Men s Women s Medium Large Medium Large (A) Overall length (Min.) 9 1/8 9 518 9 1/8 9 5/8 (Cuff edge to tip of second finger) (B) Palm width (Min.) 4 1/8 4 3/8 3 1/2 3 5/8 (At thumb crotch from folded edge to folded edge Note: A minimum measurement for the middle

11、finger of each glove shall have a dimension of three inches when measured from the crotch of the finger to the tip. Refer to Figure 1 for location of (A) and (B) measurements. the Workmanship. After completion, the finished gloves shall be thoroughly cleaned, and all loose thread, lint, and foreign

12、matter removed. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50355B 84 W 9999974 OOBL238 TTO A-A-50355B Product Demonstration Model When required offerers shall submit samples of their intended production. The Product Demonstration Model wil

13、l consist of units independently developed. Product Demonstration Models will be analyzed and evaluated by the government. Evaluation criteria and basis for award are contained in the solicitation. Product Demonstration Models will be retained by the government. One (1) Product Demonstration Model a

14、pproved by DPSC under the resultant contract will serve as a manufacturing standard for the corresponding production items delivered under this contract. Offerers are advised that the Product Demonstration Model does not relieve the successful offerer of his responsibility to perform in accordance w

15、ith the Commercial Item Description specified above. Quality Assurance Certification. The contractor shall certify that the product offered meets the salient characteristics of this description and that the product conforms to the producers own drawings, specifications, standards and quality assuran

16、ce practices. The government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of the contract. Examination. Lots of gloves shall be inspected in accordance with “Sampling Procedures and Tables fo

17、r Inspection by Attributes“, ANSI/ASQC 21.4, published by the American Society for Quality Control. Visual Examination. The inspection level for visual examination shall be II and the AQL 6.5. The sample unit shall be one glove and selection shall be by pairs. O Dimensional Examination. The finished

18、 gloves shall conform to the dimensions specified. Any dimension that is not within the established tolerance shall be classified as a defect. The sample unit shall be one glove; the inspection level shall be 5-3 and the AQL shall be 4.0. Packaqinq Examination. The fully packaged shipping containers

19、 shall be examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. The inspection level shall be S-2 and AQL shall be 2.5 defects per 100 units. Examination Defect Ma teria 1 Missing, damaged, not as required. Content Number of

20、gloves per shipping container is more or less than required. e 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50355B 84 W 9997974 0083239 937 W A-A-50355B Defects. The gloves shall be uniform in quality and shall be free from irregularities or

21、 defects which affect performance, reliability, or durability. Commercial defects - any hole, cut, tear, drop stitch, thin area or mends; any smash, needle chew, burn lump, uncoated or abraded surface, or evidence of delamination on the outside of the gloves. Evidence of strike through of the coatin

22、g on the inside of gloves affecting the comfort or function; color of the coating not as specified. Not plain or jersey knit; not 100% cotton base fabric, not polyvinyl chloride dipped. No inside seams nor a good gripping surface. Gloves not cut or fabricated in accordance with the product demonstra

23、tion model. Any marking omitted, incorrect, illegible, or incomplete. Any dimensions less than minimum. Gloves not paired. Packaqinq, Packinq, Markinq, .and Palletization Packaging, packing, marking and palletization shall be in accordance with of ASTM-D 3951, Standard Practice for Commercial Packag

24、ing, including section 7. The unit pack shall consist of 12 pairs of gloves, bundled and securely tied. The shipping container shall be packed with 144 pairs of gloves (12 bundles) of only one size and type, and shall be a single wall fiberboard box conforming to style RSC-L, Class Domestic, Variety

25、 SW, Grade 275, with a double wall liner, grade,200 of PPP-B-636. Note: Each shipping container shall contain only one National Stock Number (NSN). Unitized loads, placing boxes on pallets, shall be used whenever total quantity for shipment to one destination exceeds 250 pounds (excluding the pallet

26、) or 20 cubic feet. Pallets shall have a length of 40 inches and a width of 48 inches. Pallet loads, including the pallet, shall not exceed 54 inches in height, 43 inches in length and 52 inches in width. The containers shall be bonded onto wing type commercial 4-way entry pallets. Note: All palleti

27、zed loads shall contain only one NSN, to the maximum extent possible. When there is less than a pallet load per NSN, pallets may have containers not of the same NSN, but the pallet shall be clearly marked “mixed“ and each applicable NSN shall be listed together with its total quantity. Source of Gov

28、ernment Documents. Copies of Military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50355B 4 9999974 008124

29、0 659 W A-A-50355B Sources of Nonqovernment Documents. ANSI/ASQC 21.4 - Sampling Procedures and Tables For Inspection By Attributes (Applications for copies should be addressed to American National Standards Institute, 1430 Broadway, New York, NY 10018-3308). ASTM-D 3951 - Standard Practice for Comm

30、ercial Packaging (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103). Custodian: Navy - NU 5 Civil Agency Coordinating Activity: GSA - FSS Preparing Activity: DLA - CT Project No. 8415-0865 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-50355B 4 m 9999974 0081241 595 A-A-50352-B Figure 1 - Gloves, Cloth, Vinyl Coated, Mens and Womens 6 e a e l Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-