DLA A-A-50564-1996 FINISHING MACHINE CONCRETE ROTARY GASOLINE ENGINE HAND CONTROLLED [Superseded NAVY MIL-F-23019 E CANC NOTICE 1 NAVY MIL-F-23019 E NAVY MIL-F-23019 D NAVY MIL-F-2.pdf

1、 A-A-50564 9999974 0171232 533 II INCH-POUND A-A-50564 JULY 12. 1996 SUPERSEDING 27 NOVEMBER 1991 MIL-F-23019E(YD) COMMERCIAL ITEM DESCRIPTION 4 FINISHING MACHINE, CONCRETE, ROTARY, GASOLINE ENGINE, HAND CONTROLLED 1. SCOPE. This Commercial Item Description (CID) covers gasoline engine powered concr

2、ete fishing machine intended for making a rough and finished surface fi-om a freshly poured concrete slab. 2. SKIENT CHARACTERISTICS. 2.1 Standard commercial txoduct. The machine shall, as a minimum, be in accordance with the requirements of this CID, and shall be the manufacturers standard commerci

3、al product. Additional or better features which are not specifically prohibited by this specification, but which are a part of the manufacturers commercial product, shall be included in the unit being frnished. A standard commercial product is a product which has been sold, or is being currently off

4、ered for sale on the commercial market, through advertisements or manufacturers catalogs, or brochures, and represents the latest production model. 2.2 Gasoline enine. The gasoline engine shall be air-cooled, 4-cycle7 recoil start with the minimum engine horsepower as specified (see 6.1). 2.3 Ooerat

5、ing handle. The operating handle bar shall be adjustable. The stop switch, throttle, and blade pitch adjusting handle shall be easily reachable fi-om the operators position. Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document

6、should be sent to: Commanding Officer (Code 156), Naval Construction Battalion Center, 1000 23rd Avenue, Port Hueneme, CA 93043-4301. AMSC NIA FSC 3895 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling ServicesA-A-505b4 9999974 0171233

7、 47T A-A-50564 2.4 Spider. The spider shall be aluminum alloy, cast iron or steel, four-arm, and with variable speed trowel rotor. With the blades attached, the operating diameter shall be not less than 36 inches or 915 millimeters (mm). 2.5 Blades. The machine shall be fimished with three types of

8、abrasion-resistant-steel blades listed as follows: a. One (1) set clamp-on float blade, 10-inch by 14 -inch (254 mm by 355 mm). b. One (1) set finish blade, 6-inch by 14-inch (152 mm by 355 mm). c. Three (3) sets combination float and finish blade, 10-inch by 14-inch - (254 mm by 355 mm). 2.6 Tolera

9、nces. Dimensions shown herein shall have tolerances not to exceed It: 1/16-inch (1.58 2.7 Metric products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, providing they fall within the tolerances specified and all other

10、 requirements of this document are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch-pound units, a request should be made to the specification preparing activity for changes in the document. 3. REGULATORY REQUIREMENTS. 3.1 Recove

11、red materials. The offeror/contractor is encourageto use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. QUALITY ASSURANCE PROVISION. 4.1 Contractor certification. The contractor shall certifj, and maintain su

12、bstantiating evidence that the product offered meets the salient characteristics of this CID, and that the product conforms to the producers own drawings, specifications, standards, and quality assurance practices, and is the same product offered for sale in the commercial marketplace. The governmen

13、t reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. 5. PACKAGING. 5.1 PackagJnp; requirements. The preservation, packing, and marking shall be as specified in the contract or order (se

14、e 6.1). 2 Licensed by Information Handling Services - A-A-50564 9999974 0171234 306 A-A-50564 6. NOTES. 6.1 Ordering data. a. Title, number, and date of this CID. b. Minimum horsepower rating required (see 2.2). c. Packaging requirements (see 5.1). 6.2 Sources of documents. a. Copies of Federal Acqu

15、isition Regulations (FAR) may be obtained from the Superintendent of Documents, U. S. Government Printing Office, Washington, DC 20402. 6.3 National Stock Numbers (NSNs). The following is a list of NSNs assigned which corresponds to this CID. The list may not be indicative of all possible NSNs associated with the CID. NSN 3895-00-917-7416 MILITARY ACTIVITIES: Custodian Navy -YD1 CIVIL COORDINATING ACTIVITY GSAIFSS Preparing Activity: Navy - YD1 (Project 3895-001 7) 3 Licensed by Information Handling Services