DLA A-A-52044-1992 POLE RANGE METAL WITH CASE《带盒式金属视距尺》.pdf

1、A-A-52044 66 R 9999974 0063702 O R A-A-52044 January 3, 1992 . COMMERCIAL ITEM DESCRIPTION POLE, RANGE, METAL, WITH CASE The General Services Administration has authorized the use of this commercial item description in preference to Military specification MIL-P-20192D. This description covers one ty

2、pe of range pole containing two sections of steel tubing. The assembled length of the range pole is 6.50 feet, Its intended use is to present a view for an instrument operator sighting a straight, relatively narrow line extending vertically above the point which marks a survey station. Salient chara

3、cteristics: Design: Range Dole fabrication. The range pole shall be as specified herein. The range pole shall consist of two sections of steel tubing, a 3,50 to 6.0-inch hardened steel point and a carrying case. be made of two sections of steel tubing of nominal 1.125-inch outside diameter and of no

4、minal 0.032-inch wall thickness. shall be 6.50 feet, including a hardened steel point permanently fastened to the lower end. The steel point shall be concentric to the centerline of the pole within 0.050-inch. The construction of the telescopic sleeve joining the upper and lower sections shall be su

5、ch that both sections of the pole are the same length. A spring catch, bayonet joint or 5/8 x 11 screw joint shall be provided to lock the two sections rigidly together. The range pole shall The assembled length Carryinn - case. The two sections of the pole shall be fitted to a two - pocket carrying

6、 case made of cotton duck cloth plied-yarns unbleached with a minimum weight per square yard 8.25 ounces for the body of the case and i8.48 ounces for the reinforcing duck at the closed end, The ,reinforcing duck shall be one piece wrapped around the outside bottom of the case body. and buckle to co

7、mpletely enclose and hold the sections. The case, with the flap in the closed position, shall be not less than 42 inches long. The open end shall be provided with a strap, flap, Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any other data which may improve this

8、 document should be sent by letter to: Commander, US Army Belvoir Research, Development, and Engineering Center, ATTN: STRBE-TSE, Fort Belvoir, VA 22060-5606. AMSC N/A FSC 6675 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduct

9、ion or networking permitted without license from IHS-,-,- _ A-A-52044 66 I 9999774 0063703 2 E A-A-52044 Each of the two pockets shall have a width and depth of not less than 1.125 inches to accommodate the two range pole sections snugly, but without binding, The webbing shall be medium weight hard

10、texture, width .75-inch, shall be used as binding around all edges, including the pocket opening the case. The cotton duck webbing shall be dyed light green and treated for mildew resistance. Identification marking. The pole and case shall be identified with the manufacturers identification. Treatme

11、nt and painting. The pole shall be treated and painted. The finish coat shall be as follows: The upper 12 inches of the pole shall be painted red or orange and the remainder shall be painted in alternating white and red or orange horizontal bands 12 inches long, except that the point at the lower en

12、d shall be painted black. The edges of the ring shall be normal to the axis of the pole. Materials: Material shall be as specified herein. Metal. The metal shall be corrosion resistant or coated to be made corrosion resistant. WorkmanshiD: All parts, components, and assemblies of the range pole shal

13、l be clean and free from sand, dirt, fins, pits, sprues, scale, flux, and other harmful extraneous material. Certification of commercial item. The contractor shall certify that the product offered to the Government meets the salient characteristics of this description and that the product conforms t

14、o the producers own drawings, specifications, standards, and quality assurance practices and is the same product as the manufacturers current product offered by the contractor in the commercial marketplace for at least one year preceding the solicitation. The Government reserves the right to require

15、 proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Metric Products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, provided they fall

16、 within the tolerances specified using conversion tables contained in the latest revision of FED-STD-376, and all other requirements of this Commercial Item Description are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch/pound u

17、nits, a request should be made to the contracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejecting the product. Quality assurance: The range pole shall be examined for the following defects. Presence of one or more defects shall be c

18、ause for rejection. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52044 bb 9999974 0063704 4 A-A- 52044 1. Dimension not as specified. 2. Steel point not permanently fastened to the lower end. 3. 4. Lock does not hold two sections rigidly tog

19、ether. 5. Carrying case not as specified. 6. Identification marking not as specified. 7. Treatment and painting not as specified, 8. Materials not as specified. 9. Workmanship not as specified. Steel point not concentric with the pole centerline. 10. Packaging and marking not as specified. Regulator

20、y requirements. In accordance with section 23.403 of the Federal Acquisition Regulations, the Government?s policy is to acquire items composed of the highest percentage of recovered materials practicable, consistent with maintaining a satisfactory level of competition without adversely affecting per

21、formance requirements or exposing the supplier?s employees to undue hazards from the recovered materials. Preservation, packaging. packing. labeling, and markinq. The Preservation, packaging, packing, labeling, and marking shall be as specified in the contract or order. CID based part identification

22、 number. The following part identification numbering procedure is for Government purposes and does not constitute a requirement for the contractor. Part or identifying number (PIN): The part or identifying number for the range pole shall be as follows: CID Document identifier ,i?4 Notes: herein and

23、include the following information in procurement documents: The procuring agency should specify the preferred options permitted 1. Title, number, and date of this item description. 2. When the commercial item description is used for acquisition, the commercial item certification clause must appear i

24、n the solicitation. FED-STD-376 is available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094. The following are suggested sources of supply for this item description (competition is not limited to these sources.): a. Sokkisha Co., LTD, 10 H

25、achimanyama l-Chome, Setagaya-ku, Tokyo 156 Japan, Telephone: 813-302-7071. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52044 66 I 7777974 0063705 6 A-A-52044 b. North America Survey Supply Co., 2070-T Markem Rd., Philadelphia, PA 19116. Th

26、e preparing activity for this item description is the U.S. Army Belvoir Research, Development, and Engineering Center, ATTN: STRBE-TSE, Fort Belvoir, VA 22060-5606. MILITARY INTERESTS: CIVIL AGENCY COORDINATING ACTIVITY: Custodians Army - ME Review activitv DIA - GS User activitv Navy - MC GSA - FCGC PREPARING ACTIVITY: Army - ME Y Project 6675-0892 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-