DLA A-A-52203-1993 SUSPENDERS TROUSERS (FLYING SUIT)《长裤(飞行员西装)吊裤》.pdf

1、A-A-52203 W 9999974 OL44bL9 7TO A-A-52 2 03 03 MAY 1993 COMMERCIAL ITEM DESCRIPTION SUSPENDERS, TROUSERS (FLYING SUIT) The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-S-6790. Abstract. This commercial item description covers suspend

2、ers for use with flying clothing. Classification. The Suspenders, Trousers shall be in the following types : Type I - Elastic Type II - Nonelastic Salient Characteristics. The suspenders shall consist of two strips of webbing, 1-1/2 inch wide for Type I - Elastic and Type II - Nonelastic and shall b

3、e colored sage green shade No. 1514, DPSC HANDBOOK 4120.1. The suspenders will have a crisscross pattern with wire buttonholes on two of the ends and leather buttonholes on the other two ends as shown in figure 1. Beneficial comments (recommendations, additions, deletions) and any pertinent data whi

4、ch may be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSCD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the en

5、d of this document or by letter. AMSC N/A FSC 8440 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. O Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52203 m 9999974 0144620 412 m A-A-55203 Material. woven constru

6、ction measuring i-1/2 inch wide a ferrule and a suspender hook made from 0.015-inch 1010 hot rolled steel, and a complete snap fastener set. The Type I elastic webbing shall be a cotton, and rubber, Label/markinq. indented or marked with the manufacturers name or trademark of such characters as to b

7、e identifiable with the manufacturer. Each suspenders shall be permanently and legibly WorkmanshiD. After completion, the finished suspenders shall be thoroughly cleaned, and all loose thread, lint, sharp edges, and foreign matter removed. Product Demonstration Model. When required, offerers shall s

8、ubmit samples of their intended production. The Product Demonstration Model will consist of units independently developed. Product Demonstration Models will be analyzed and evaluated by the government. Evaluation criteria and basis for award are contained in the solicitation. Product Demonstration M

9、odels will be retained by the government. One (1) Product Demonstration Model approved by DPSC under the resultant contract will serve as a manufacturing standard for the corresponding production items delivered under this contract. Offerers are advised that the Product Demonstration Model does not

10、relieve the successful offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. Requlatorv Requirements. recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. Quality Assurance The offeror/contractor is encoura

11、ged to use Certification. The contractor shall certify that the product offered meets the salient characteristics and the requirements of this commercial item description, and where certificates of compliance are submitted, the government reserves the right to require proof of such conformance prior

12、 or to check such items to determine the validity of the certificate. Examination. I1Sampling Procedures and Tables for Inspection by Attributes“, ANSI/ASQC 21.4, published by the American Society for Quality Control. Lots of suspenders shall be inspected in accordance with 2 Provided by IHSNot for

13、ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52203 = 7777771.1 011.14621 359 = A-A-552 O 3 Visual Examination. The suspenders shall be examined for the defects listed below. The sample unit is one suspender. The inspection level shall be II and the acceptable qualit

14、y level (AQL), expressed in terms of defects per hundred units, shall be 2.5. The lot size shall be expressed in units of suspenders. Packaaina Examination. examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. The inspection

15、 level shall be S-2 and AQL, expressed in terms of defects per hundred units, shall be 2.5. The fully packaged shipping containers shall be Dimensional Examination. dimensions specified. Any dimension that is not within the established tolerance shall be classified as a defect. one; the inspection l

16、evel shall be S-3 and the AQL shall be 4.5. The finished suspenders shall conform to the The sample unit shall be Packaaina Examination. examined in accordance with defects listed below. The lot size shall be the number of shipping containers in the inspection lot. The inspection level shall be S-2

17、and AQL shall be 2.5. The fully packaged shipping containers shall be Examination Defect Mater ia1 Missing, damaged, not as required. Marking (exterior Omitted, incorrect, illegible, of and interior) improper size, location, sequence or method of application. Content Workmanship Palletization Number

18、 of suspenders per shipping container is more or less than required. Incomplete closure of container Length, width, or height flaps, loose or inadequate strapping. exceeds specified maximum requirements Pallet type not as specified Load not bonded as specified 3 Provided by IHSNot for ResaleNo repro

19、duction or networking permitted without license from IHS-,-,- A-A-52203 9999974 0144622 295 A-A-552 03 Defects. The suspenders shall be examined for the following defects: any hole, cut, tear, color not as specified; any spot or stain (outside); thread ends not removed; label missing, incorrect, or

20、illegible; brand marks and excessive softness of leather; broken or malformed, corroded areas, burr or sharp edges; measurement of item not as specified. Preservation, Packinq, and Markinq. The preservation, packing, and marking shall be as specified in the contract or order. Source of Government Do

21、cuments. Copies of Military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonqovernment Documents. ANSI/ASQC 21.4 - Sampling Procedures and Tables For Inspection By Attributes (Applications for copies

22、 should be addressed to American National Standards Institute, 1430 Broadway, New York, NY 10018-3308.) Custodian: Army - AV Navy - AS Air Force - 99 Review Activity: Air Force - 82 Civil Agency Coordinating Activity: GSA - FSS Preparing Activity: DLA - CT User Activity: Project No.8440-0204 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-52203 9999974 0344623 121 A-A-5220, v) W 3c o f i w e y O UJ L w - O I 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-