DLA A-A-55175-1993 TRUNKS PHYSICAL FITNESS UNIFORM《体能制服游泳裤》.pdf

1、A-A-55175 9999974 0127760 955 = I INCH-POUND I a COMMERCIAL ITEM DE A-A-551 7 5 1 March 1993 IPTION TRUNKS, PHYSICAL FITNESS UNIFORM The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-T-44213. Abstract. This commercial item description

2、 covers one type of cotton/polyester blend trunks used by Military personnel of th Department of Defense as a component of the Physical Fitness Uni form. Salient Characteristics. The trunks shall be a boxer style, having a covered elastic waistband with three rows of stitching, 3/4 2 1.4 incn hemmed

3、 leg openings, leg vents at side seams, a full, pre-assembled liner, and a key/change pocket with rounded corners located on the upper right front waistband. The pocket shall be 3 5 1/2 inches in width at top folded edge and 4 5 1/2 inches in length from the bottom edge of waistband to bottom edge o

4、f pocket (see Figure 1). All seams shall be overedged stitched and the gage of the stitching shall be 3/16 2 1/16 inch. Figure 1 is furnished solely for guidance and information. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this

5、document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. I

6、AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55175 = 9999974 0127763 91 Characteristic A-A- 5 5 17 5 Requirement (minimum) Material. The cloth

7、for the body of the trunks shall be a jersey knit using a cotton/polyester blended yarn of 50 2 5 percent cotton and the remaining percent polyester. The cloth shall match the standard sample for color heather grey 467 when viewed under filtered tungsten lamps that approximate artificial daylight an

8、d that have a correlated color temperature of 7500 -+ 200 K, with illumination of 100 2 20 foot candles, and shall be a good match to the standard sample under incandescent lamplight of 2300 2 200K, and conform to the characteristics in Table I below. Table I. Basic Material Testinq Weight, ounces/y

9、ard 2 Wales per inch Courses per inch Bursting strength (lbs.) Colorfastness: Light 1/ Laundering (after Crocking Perspiration Ph (Min. to Max.) 3 cycles 5.8 2 0.5 20 30 75 4 4 3.5 4 5.0 to 8.5 Test Method ASTM D-3887 ASTM D-3887 ASTM D-3887 ASTM D-3887 AATCC 61 AATCC 8 AATCC 16 AATCC 15 ASTM D-2165

10、 - i/ Except that the standard fade hours shall be 40 hours. Liner. The pre-assembled liner to be used in each of the trunks shall be style #B15 of ADS, Inc. or equal (see NOTES). Liner sizes shall be identified and matched to trunk sizes as shown in the following manner. Liner color identification

11、Trunks Pattern B blue band Sizes X-small - -Small Pattern C yellow band Sizes Medium - Large Pattern D green band Size X-large - XX-large Elastic webbinq. The elastic webbing for the waistband shall meet the requirements listed below. Characteristic Requirement Fabrication: Width (inches) 1-5/10 +1/

12、4 -1/16 Weight ounces per linear yard 0.50 (minimum) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I. I a A-A-55175 9999974 OL277b2 728 A-A- 55 17 5 Characteristic Reauirement Construction: Warp ends/width crocket 16 (minimum) Elastic strands, fu

13、ll width 14 (minimum) Filling yarns per inch 46 (minimum) Fiber content: Warp yarn (crocket) Elastic strands Filling yarn Polyester Spandex Polyester Sizes. The trunks shall be provided in the following sizes: X-Small (24-26) Small (28-30) Medium (32-34) Large (36-38) X-Large (40-42) XX-Large (44-46

14、) NOTE: X-Small, Small, Medium, Large, X-Large, XX-Large may be abbreviated as XSM, SM, MED, LG, XLG and XXLG. Thread. The thread for the trunks shall be a 50/2 spun polyester, or an equivalent cotton-covered or polyester-covered polyester core, or a high tenacity, textured polyester of approximatel

15、y 45 Tex. The color of the thread shall be dyed to approximate the shade of the basic material. Label. A commercial type label is acceptable provided an additional printed cloth label containing the contractors name, contract number, size and National Stock Number (NSN) is caught on the stitching of

16、 the commercial label. The commercial label shall include fiber and laundering information. The body of the instruction label shall be as follows: CARE INSTRUCTIONS Hand or machine wash in cold or warm water Do not Bleach or Iron. Tumble dry at low or medium (maximum 120OF). setting (maximum 160OF).

17、 Patterns. Commercial patterns shall be used. These patterns shall conform to the design cited herein and to the finished measurements listed in Table II. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55175 I 74 O1277b3 bbq I A-A-5517 5 Sizes

18、 and Measurements. The finished trunks shall conform to the measurements in Table II below. Table II. Finished measurements (inches) Waist Waist Leg Re- EX- Front Open- laxed tended Rise Outseam Thigh ing Slit A/ - B/ - C/ - D/ - E/ - F/ - G/ Size - X-Small 11 17 12 15-1/2 12-1/2 11 2 Small 12 19 12

19、-1/2 16 13-1/4 12 2 Medium 13 21 13 16-1/2 14 13 2 Large 14 23 13-1/2 17 14-3/4 14 2 X-Large 15 25 14 17-1/2 15-1/2 15 2 XX-Large 16 27 14-1/2 18 16-1/4 16 2 Tolerance +i Min. +1 +1 +1 +1 - + 1/4 -1/2 -1/2 -1/2 -1/2 -1/2 - A/ - B/ - C/ - D/ - E/ Waist relaxed - measure across top of trunks with trun

20、ks laying flat. Waist extended - measure across top of trunks while stretching waist. Front rise - measure along front center seam from top of elastic waistband to crotch seam Outseam - measure along side seam from top of trunks to bottom of leg hem. Thigh - measure parallel to leg opening from crot

21、ch point to outside fold of leg. Lay flat, disregard outseam. - F/ G/ Slit - measure from beginning of slit to leg bottom. Leg opening - measure from side slit to folded edge when trunks are laid down flat. Workmanship. After completion, the finished trunks shall be clean, and all loose thread, lint

22、, and foreign matter removed. The trunks shall conform to the quality established by this document. Product Demonstration Model. When required, offerers shall submit samDles of their intended production. The Product Demonstration Model will consist f units independently developed. Product Demonstrat

23、ion Models will be analyzed and evaluated by the government. Evaluation criteria and basis for award are contained in the solicitation. Product Demonstration Models will be retained by the government. One (1) Product Demonstration Model approved by DPSC under the resultant contract will serve as a m

24、anufacturing standard for the corresponding production items delivered under this contract. Offerers are advised that the Product Demonstration Model does not relieve the successful offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. O a e 4 P

25、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A955 175 m 9999974 O327764 5T0 m A-A-55 17 5 Quality Assurance Certification. The contractor shall certify that the product offered meets the salient characteristics of this description and that the pr

26、oduct conforms to the producers own drawings, specifications, standards and quality assurance practices. The government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of the contract. Reliance

27、on contractor QA systems shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the government for acceptance comply with all requirements of the contract. Examination. Trunk lots shall be inspected in accordance with “Sampling Procedures and Ta

28、bles for Inspection by Attributes“, ANSI/ASQC 21.4, published by the American Society for Quality Control. Visual Examination. The trunks shall be examined for the defects listed below. The lot size shall be expressed in units of trunks. The sample size is one of the trunks. The inspection level for

29、 visual examination shall be II and the acceptable quality level (AQL), expressed in terms of defects per hundred units, shall be 1.5. Defects. The trunks shall be examined for the following defects: any hole, cut, tear, color not as specified; any spot or stain (outside); thread ends not removed; a

30、ny components missing or other than specified; any seam twisted, puckered or pulled affecting appearance; any needle chews or tight tension; any part of trunks badly pleated, or caught in any unrelated row of stitching; any open seam; any omitted hems; label missing, incorrect, or illegible; measure

31、ment of item not as specified. Dimensional Examination. The finished trunks shall conform to the dimensions specified. Any dimension that is not within the established tolerance shall be classified as a defect. The sample unit shall be one of the trunks; the inspection level shall be S-3 and the AQL

32、, expressed in terms of defects per hundred units, shall be 2.5. Shrinkaqe. The completed trunks shall not shrink nor elongate more than 10 percent ir_ width or length when tested as specified in end item shrinkage testing, except that the measurement to be taken after testing shall be the outseam a

33、nd the thigh. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55175 W 9999974 0127765 V37 W A-A-55 17 5 End item shrinkaqe testinq. The end item shall be tested for shrinkage as specified in Test Method 150 of AATCC using normal machine cycle,

34、( 120 2 5OF) washing temperature and cotton/sturdy dryer setting (150 10F). The trunks shall not be moistened or pressed before measuring. The measurement shall be taken to the nearest 0.1 inch with the trunks laid flat. Any dimensions not within the specified tolerance shall be classified as a defe

35、ct. The lot shall be expressed in units of trunks. The sample unit shall be one of the trunks. The inspection level shall be S-3 and the AQL, expressed in terms of defects per hundred units, shall be 4.0. Packaqinq Examination. The fully packaged shipping containers shall be examined in accordance w

36、ith defects listed below. The lot size shall be the number of shipping containers in the inspection lot. The inspection level shall be S-2 and the AQL, expressed in terms of defects per hundred units, shall be 1.0. EXAMINE DEFECT Marking Omitted; incorrect; illegible; (exterior and interior) of impr

37、oper size, location, or method of application Ma teria 1 s Workmanship Content Palletization Any component missing, damaged, or not as specified Inadequate application of components, such as: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling Number of it

38、ems in container is more or less than required NSN shown on one or more items not as specified on shipping container Length, width, or height exceeds specified maximum requirements Pallet type not as specified Load not bonded as specified 6 Provided by IHSNot for ResaleNo reproduction or networking

39、permitted without license from IHS-,-,-A-A-55175 = 9999974 O1277bb 373 A-A-55 17 5 Reuulatory Requirements. The offeror/contractor is encouraged to use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. Packaainq. Overseas. Packaqinq. Each pair of trunks shal

40、l be folded and placed in a plastic bag. Packinq. Twenty two pairs of trunks shall be packed in a fiberboard box conforming to style RSC-L, grade 275 of PPP-B-636. The inside dimensions of the box shall be approximately 23-1/2 inches in length, 15 inches in width and 12 inches in depth. The box shal

41、l be closed in accordance with the appendix of PPP-B-636. Palletization. Boxes shall be palletized on a 4-way entry pallet in accordance with load type Ia of MIL-STD-147. Each prepared load shall be bonded with primary and secondary straps in accordance with bonding means C and D, or film bonding me

42、ans F or G. Pallet pattern shall be number 3 in accordance with the appendix of MIL-STD-147. Markinq. Marking shall be in accordance with MIL-STD-147. Domestic. Packauinq, Packinq, Palletization and Marking. Packaging, packing, palletization and marking shall be in accordance with ASTM D 3951. Sourc

43、e of Government Documents. Copies of Military and Federal documents are available from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonqovernment Documents. ANSI/ASQC 21.4 - Sampling Procedures and Tables For Inspection By Attributes (Appli

44、cations for copies should be addressed to American National Standards Institute, 1430 Broadway, New York, NY 10018- 3308. ) 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55175 m 9999974 O327767 20T m A-A-5 5 17 5 AATCC Test Methods (Applicati

45、ons for copies should be addressed to the AATCC National Headquarters, P. O. Box 12215, Research Triangle Park, NC 27709-2215. ) ASTM Test Methods (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) NOTES : Suqqested

46、source for liner. A suggested source for the liner is ADS, Inc., P. O. Box 1927, Ledbetter Road, Rockingham, NC 28379. Equal item. Prior to use of an “or equal item“, the su;?plier shall submit the item with supporting data to the contracting officer for subsequent approval or disapproval by the res

47、ponsible military agency. Custodian: Army - GL Review Activity: Army - MD 8 Civil Agency Coordinating Activity: GSA - FSS Preparing Activity: DLA - CT Project No. 8415-0899 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55175 = 9999974 Ol1277b 14b = A-A-55 17 5 A B RELAXED EXTENDED G FIGURE 1 - TRUNKS, PHYSICAL FITNESS UNIFORM (CUT-AWAY VIEW) 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-