DLA A-A-55225-1993 SCARF NECKWEAR WOMAN-S ACRYLIC《女式丙烯酸脖颈丝巾》.pdf

1、A-4-55225 9599974 0345463 933 = I INCH-POUND 1 A-A-55 2 25 Auqust 17, 1993 COMMERCIAL ITEM DESCRIPTION SCARF, NECKWEAR, WOMANS ACRYLIC The General Services Administration has authorized the use of this Commercial Item Description in preference to MIL-S-43317. Abstract. This Commercial Item Descripti

2、on covers the requirements for a womens acrylic neckwear scarf. The scarf is intended for wear by female personnel of the Department of the Navy. Salient Characteristics. The scarf shall be made of one piece single thickness material with fringed ends and overedge stitched side edges. The length dir

3、ection of the scarf shall be in the warp direction of the material, with even 3/4 (+1/4,-1/8) inch fringing on the ends. The overedge stitch on the sides of the scarf shall be 3/16 inch wide, 16 - 18 stitches per inch, with the chain at each end of stitching the same length as the fringe (-1/4 inch

4、tolerance). The finished dimensions of the scarf shall be 46-1/2 to 48 inches long (including fringe), and 10-1/2 to 11-1/4 inches wide (including overedge stitching). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document sh

5、ould be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A DIST

6、RIBUTION STATEMENT A. FSC 8445 Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55225 = 74 0145464 8T A-A-5 5 2 25 Materials. Basic cloth. The fiber for the basic cloth shall be acrylic, semi

7、-dull, 2 ply warp and filling yarns of a suitable staple length, twisted with 6-9 turns per inch, Z twist. The ply yarn consists of two single yarns, each with 5-9 turns per inch, S twist. The weave shall be a crowfoot satin, repeating on 4 ends and 4 picks, as shown in the diagram below: X X X X Th

8、e Finished cloth shall be chemically bleached white and may be supplemented with optional brighteners which fluoresce to the blue region, matching the Navy shade White 3032, and shall conform to the requirements specified in Table I when tested as specified. Table I. Requirements and test methods Ch

9、aracteristics Requirements Test method Fiber identification As stated above Weight oz./sq. yd. 3.8 (min) ASTM-D 3776-85 Option C Yarns per inch: Warp 28 ends/inch (min) ASTM-D 3775-85 Filling 20 picks/inch (min) Breaking strength: Warp 40 lbs. (min) Filling 25 lbs. (min) ASTM-D 5034-90 Nonfibrous ma

10、terial 2.0% Max. ASTM-D 629-88 5.0 - 8.5 ASTM-D 2165-90 PH 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55225 = 9999974 OL454b5 70b A-A-55 2 25 i/ Unless otherwise specified, a certificate of compliance shall be submitted and will be accepta

11、ble for the stated requirements. e- Thread, cotton. The cotton thread for seaming the edges of the scarf shall be ticket number 00, 3 ply, conforming to type III (mercerized machine thread) of A-A-52094 except that the colorfastness requirements do not apply. The color of the thread shall be white A

12、.H. C.A. 66050 in accordance with the Department of Defense Standard Shades for Sewing Threads. Label/taq. Each scarf shall be individually coded with a type VIII, class 17 of DDD-L-20 label/tag bar code for personal clothing items, bar code is completely visible in the packaging. The scarf shall be

13、 folded so that the label/tag Workmanship. The finished scarves shall conform to the quality of product established by this document. The occurrence of defects shall not exceed-the applicable acceptable quality levels. Product Demonstration Model. When required, offerers shall submit samples of thei

14、r intended production. The product demonstration model will consist of units independently developed. Product demonstration models will be analyzed and evaluated by the government. Evaluation criteria and basis for award are contained in the solicitation. Product demonstration models will be retaine

15、d by the government. One (1) product demonstration model approved by DPSC under the resultant contract will serve as a manufacturing standard for the corresponding production items delivered under this contract. Offerers are advised that the product demonstration model does not relieve the successfu

16、l offerer of his responsibility to perform in accordance with the Commercial Item Description specified above. Quality Assurance Certification. The contractor shall certify that the product offered meets the salient characteristics of this description and that the product conforms to the producers o

17、wn drawings, specifications, standards and quality assurance practices. The government reserves the right to require proof of such conformance prior to the first delivery and thereafter as may be otherwise provided for, under the provisions of the contract. Reliance on contractor QA systems shall no

18、t relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the government for acceptance comply with all requirements of the contract. 0 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-4-5.5225 m 7779974 O

19、Lq54bb 642 m A-A-5 5 2 2 5 Examination Visual Examination. The scarf shall be examined for the defects listed below. The lot size shall be expressed in units of scarfs. The sample unit is one scarf. Defects. The scarfs shall be examined for the following defects: Any hole, cut, tear, smash, floats,

20、slubs, needle chew, Width of overedge stitching less than 1/8 inch or more than Fringe missing on one or both ends, ragged or uneven. Break in overedge stitching, runoff, loose tension, exposed Spot, stain clearly visible or thread ends not trimmed. Bar code label/tag omitted or not scannable, human

21、-readable shade bar, streak or wrong color. 3/16 inch; overedge stitching missing. Thread wrong color, not size or type specified. loops or tight tension, resulting in puckering. interpretation (HRI) omitted or illegible. Dimensional Examination. The finished scarf shall conform to the dimensions sp

22、ecified. Any dimension that is not within the established tolerance shall be classified as a defect, The sample unit shall be one scarf. Packaqinq Examination. The fully packaged shipping containers shall be examined in accordance with defects listed below. The lot size shall be the number of shippi

23、ng containers in the inspection lot. EXAMINE DEFECT Marking Omitted; incorrect; illegible; (exterior and interior) of improper size, location, or method of application Ma ter i a 1 s Workmanship Content Any component missing, damaged, or not as specified Inadequate application of components, such as

24、: incomplete closure of container flaps, loose strapping, improper taping, or inadequate stapling Number of items in container is more or less than required NSN shown on one or more items is not as specified on shipping container 4 Provided by IHSNot for ResaleNo reproduction or networking permitted

25、 without license from IHS-,-,-A-A-55225 U 9997974 0345467 589 = A-A-5 5 2 25 EXAMINE DEFECT - cont. Palletization Length, width, or height exceeds specified maximum requirements Pallet type not as specified Load not bonded as specified Reaulatorv Requirements. The offeror/contractor is encouraged to

26、 use recovered materials in accordance with Public Law 94-580 to the maximum extent practicable. Preservation, Packinq, and Markinq. The preservation, packing, and marking shall be as specified in the contract or order. Source of Government Documents. Copies of Military and Federal documents are ava

27、ilable from: Standardization Documents Order Desk Bldg. 4D 700 Robbins Avenue Philadelphia, PA 19111-5094 Sources of Nonqovernment Documents. THE COLOR ASSOCIATION OF THE UNITED STATES Department of Defense Standard Shades for Sewing Thread (Application for copies may be obtained from the Color asso

28、ciation of the United States, 343 Lexington Ave., New York, NY 10016). ASTM-D 629 - Nonfibrous materials ASTM-D 3775 - Yarns per inch ASTM-D 3776 - Weight ASTM-D 5034 - Breaking strength ASTM-D 2165 - PH (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) Custodian: Navy - NU Civil Agency Coordinating Activity : GSA - FSS Preparing Activity: DLA - CT Project No. 8445-0122 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-