DLA A-A-55309-1997 SWEATSHIRT PHYSICAL FITNESS UNIFORM《体能制服汗衫》.pdf

1、1 INCH-POUND I A-A-55309 June 03,1997 COMMERCIAL ITEM DESCRIPTION SWEATSHIRT, PHYSICAL FITNESS UNIFORM The General Services Administration has authorized the use of this commercial item description in preference to MIL-S-44212. 1. SCOPE. This commercial item description covers one type of a knitted

2、jersey fleece sweatshirt. The sweatshirts are intended for use as a component of the Physical Fitness Uniform by personnel of the Department of Defense. 2. SALIENT CHARACTERISTICS 2.1 Description. The sweatshirt shall be hooded, long sleeve, and have a front slide fastener closure. The hood shall be

3、 of double thickness with eyelets and drawcord, the body includes split muff pockets (double thickness) and rib knit side panels (3-1/2 inches wide). The cuffs and waist shall be rib knit finished. 2.2 Materials. 2.2.1 Basic material. The cloth for the body, hood, sleeves and muff pockets of the swe

4、atshirt shall be a jersey knit fleece cloth consisting of 55 (+/-5)% cotton for comfort and absorbency, 1- 2% rayon or polyester and the remaining percentage acrylic fiber or a blend of fibers with comparable properties. The cloth for the cuffs, waist, and side panels shall be plaited 1x1 rib knit c

5、onsisting of 47 (+/-5)% cotton, 2-3% rayon or polyester and the remaining percentage acrylic fiber or a fiber with comparable properties. The color shall be light Heather Gray 446. Testing shall be in accordance with Table I. The sweatshirt shall be cut in the wale direction. 2.2.2 Thread. The threa

6、d for seaming and stitching shall be 2-ply cotton-covered polyester or spun polyester. The color shall be light gray, DoD shade AX, C.A. 66064 and shall show colorfastness to laundering, perspiration and light. Testing shall be in accordance with Table I. 2.2.3 Drawcord. The drawcord for the hood sh

7、all be 3/16 inch diameter, 100 percent filament nylon or a fiber with comparable properties having a minimum breaking strength of 150 pounds. The color shall be light gray, Dod shade AX, C.A. 66064 and shall show colorfastness to laundering. Testing shall be in accordance with Table I. Beneficial co

8、mments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document should be sent to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn.: DPSC-FNS, 2800 South 20th Street, Philadelphia, PA 19145-5099. AMSC N/A FSC 8415 DISTRIBUTIO

9、N STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55309 = 9999974 Si175839 T42 * REQUIREMENTS MINIMUM MAXIMUM 8.5 (+/-0.5) 8.5 (+/-0.5) 19 A-A-55309 L TEST METHOD ASTM D3776 AST

10、M D3887 2.2.4 Eyelet. The eyelet for the waist drawcord shall be one piece, brass with a natural finish and a inside diameter large enough to allow the drawcord to pass easily through. 90 - 1/ AND 2/ 2.2.5 Slide fastener. The slide fastener shall be a separating, nonreversible, open automatic lock,

11、with a right hand separating unit bottom stop. The slide fastener shall be plastic, size MS with a long pull tab. The tape width shall be 9/16 (+/-1/32) inch wide. The color, including chain, tape and slider shall match the basic material. AATCC- 135 2.3 Reshrinking The knitted cloth shall be preshr

12、unk before being cut, such that the sweatshirts will meet all shrinkage requirements specified in Table I. 5.0 2.4 Figures. Figures 1 and 2 are furnished for information purposes only. To the extent of any inconsistencies between the written commercial item description and Figures 1 and 2, the writt

13、en commercial item description shall govern. TABLE I. - Requirements 8.5 CHARACTERISTICS WEIGHT OZJSQ. YD.: Jersey knit fleece Rib knit 1.8 CONSTRUCTION: Jersey Knit Fleece: Wales per inch Courses per inch Rib Knit: Wales per inch Courses per inch Jersey knit fleece Rib knit BURSTING STRENGTH (ibs)

14、DIMENSIONAL STABILITY COLORFASTNESS (MIN.) Jersey and rib knit Laundering: Light: Perspiration: Crocking Jersey and rib knit BREAKING STRENGTH (LBS) Thread Drawcord PH I ASTMD2256 18 25 75 ASTM D3787 AATCC-6 1, TM 3A AATCC-16. Option A AATCC- 15 AATCC-8 3.5 FED-STD-28 1 1 150 1 I 2 Provided by IHSNo

15、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55309 9997974 0175840 764 REQUIREMENTS CHARACTERISTICS MINIMUM f MAXIMUM A-A-55309 TEST METHOD TABLE I. - Requirements (continued) Rayon or polyester or equivalent Acrylic or equivalent 1 to 2% Remaining percentage

16、IDENTIFICATION Cot ton: Jersey knit fleece 1x1 rib knit 55 (+/-5)% 47 (+/-5)% The finished sweatshirts, after five (5) launderings and dryings shall not elongate more than 5.5 percent or shrink more than 8.0 percent lot average, with no sample unit to exceed 10.0 percent for the outseam and shall no

17、t shrink more than 10.0 percent for the sleeve length, body length and chest width. The sweatshirts shall be tested for shrinkage by using normal machine cycle 12Oo(+/-5“F) washing temperature, and dryer setting 140F. The sweatshirts shall not be moistened or pressed before measuring. Measurements s

18、hall be taken to the nearest O. 1 inch with the sweatshirts laid flat. Elongation shall be reported with a minus (-) sign. 2.5 Finished measurements. The sweatshirts shall be provided in the following measurements: TABLE II. - Finished measurements (in inches) (A) U2 Chest width: Measure just below

19、armhole, flat across the chest. (B) Length: Measure high point of shoulder to bottom including rib knit waist. (C) Armhole: Measure shoulder seam point to underarm; (straight line, point to point). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-

20、A-55307 7777974 0175841 bTO W SIZE X-SMALL SMALL MEDIUM LARGE X-LARGE A-A-55309 DISTANCE DOWN FROM NECK SEAM +/- U2 INCH 3 3-1/2 4 4-1/2 5 ) Sleeve Overarm: Measure shoulder seam to sleeve, including rib knit cuff. (E) Sleeve Underarm: Measure underarm seam to sleeve, including rib knit cuff. (F) Sl

21、eeve Opening: Measure at cuff seam with rib extended until the body fabric lays flat. (G) Neck Opening Relaxed: Fold center front to center back and measure seam. (H) Sleeve Trim: Measure from seam to end of double thickness rib knit cloth. (I) Bottom Trim: Measure from seam to end of double thickne

22、ss rib knit cloth. (J) Side Panel Width: Measure seam to seam of double thickness rib knit cloth. (K) Hood Width: Lay flat, measure from fold to back seam. (L) Hood Length: Layflat, measure top fold to neck seam in center of hood. (M) Pocket Width: Measure center from fold at slide fastener to edge

23、of pocket at widest point. (N) Pocket Length: Measure from top edge of pocket to rib knit bottom hem. 2.6 Patterns. Government patterns shall be furnish upon request. Commercial patterns shall be used. 2.7. Labeldmarking. A commercial type label shall include the contractor?s name, contract number,

24、size and National Stock Number (NSN). The commercial label shall include fiber and laundering information. Colorfastness to laundering shall apply. The commercial type label shall be attached to the inside of the sweatshirt. The care instructions shall read as follows. CARE INSTRUCTIONS Hand or mach

25、ine wash in cold or warm water (maximum 120F) Do Not Bleach or Iron. Tumble Dry low setting (maximum 140F) 2.7.1 Barcode label. The sweatshirts shall have a printed bar code label that is clearly legible and readable by scanner. The bar coding element shall be a 13 digit national stock number (NSN).

26、 The label shall be a medium to high code density and shall be located so that it is completely visible on the item when it is folded and/or packaged as specified. 2.7.2 Marking. The ink for screen printing ?ARMY? to the sweatshirt shall be black thermal plastic base ink (withstanding temperatures t

27、o 300F) or equal. The black ?ARMY? markings shall be screen printed on the front of the sweatshirt as shown in Figure 1. Letters shall measure 5/8 (+/-1/16) inch wide and 3 (+/-1/4) inches in height, see Figure 2. The overall width shall be 12 (+/- 1/4) inches and shall be positioned as specified in

28、 Table III. The printing shall have a rating of ?4? after 15 launderings when tested as specified in AATCC-61. TABLE III.- Marking location (in inches) 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55309 u 999797u 0175842 537 m A-A-55309 3. R

29、egulatory Requirements. The offerorkontractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. QUALITY ASSURANCE PROVISIONS 4.1 Product conformance. The products provided shall meet the sal

30、ient characteristics of this commercial item description, conform to the producers own standards and quality assurance practices, and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 4.2 Visual examination. The swe

31、atshirts shall be examined for the following defects: Any hole, cut, or tear; any variation of shade; any spot or stain (outside), rancid odors, burns or scorch; raw edges, open seams, thread ends not removed, any material defects, distorted parts or poor workmanship; color not as specified; any com

32、ponent part omitted; label missing, incorrect, or illegible; measurement of item not as specified; bar code omitted or not readable by scanner; human-readable interpretation (HRI) omitted or illegible; bar code not visible on folded, packaged item; bar code causes damage to the item; any items not p

33、ackaged in accordance with the contract or purchase order. 5. Preservation, packing, and marking. The preservation, packing, and marking shall be as specified in the contract or order. 6. NOTES 6.1 Source of Government documents. Copies of military and Federal documents are available from: Standardi

34、zation Documents Order Desk Bldg. 4D 700 Robbins Avenue, Bldg. 4D Philadelphia, PA 19 1 1 1-5094 6.2 Source of non-Government documents ASTM Test Methods (Applications for copies should be addressed to American Society For Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1 187.) AATCC

35、 Test Method (Applications for copies should be addressed to American Association of Textile Chemists and Colorists (AATCC), P.O. Box 12215, Triangle Park, NC 27709-2215.) THE COLOR ASSOCIATION OF THE UNITED STATES, INC. Department of Defense Standards Shades for Threads (Applications for copies of

36、color cards should be addressed to the Color Association of the U.S., 200 Madison Avenue, New York, NY 10016.) 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A45309 6.3 Acceptance criteria. Acceptance criteria shall be as specified in the contra

37、ct or purchase order. MILITARY INTERESTS: Custodians Army - GL Review Activities Army-MD CIVIL AGENCY COORDINATING ACTIVITY: GSA - FSS PREPARING ACTIVITY: DLA - CT Project 8415-0107 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* A-A-55309 FIGURE

38、 1. SWEATSHIRTS, PHYSICAL FITNESS UNIFORM (PFU) 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-55307 m 9999974 0375845 246 m A-A-55309 FIGURE 2. NOTE: The width of each letter shall be 5/8 (+/- 1/16) inch. The style of lettering shall be as shown above. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-