DLA A-A-59309-1999 TESTER TORQUE WRENCH [Superseded DLA MIL-T-26639 C CANC NOTICE 1 DLA MIL-T-26639 C (4) DLA MIL-T-26639 C (3) DLA MIL-T-26639 C (2) DLA MIL-T-26639 C (1) DLA MIL-.pdf

1、INCH-POUNDA-A-5930921 July 1999 SUPERSEDINGMIL-T-26639C14 March 1969Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any otherdata which may improve this document should be sent to: Defense Supply Center Richmond(DSCR), ATTN: DSCR-VBD, 8000 Jefferson Davis Highway

2、, Richmond, VA 23297-5610.AMSC N/A FSC 6635DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.COMMERCIAL ITEM DESCRIPTIONTESTER, TORQUE WRENCHThe General Services Administration has authorized the use of thiscommercial item description for all federal agencies.1. SCOPE.

3、 This commercial item description (CID) covers torque wrench testers withmechanical indicating dials for use in test and verification of hand-held torque wrenches of alltypes.2. CLASSIFICATION. The torque wrench tester shall be of the following types and sizes. Thetype and size to be furnished shall

4、 be as specified (see 7.2(b).Type I - Single station, single rangeType II - Dual station, single range, dual scaleType III - Single station, dual range or dual station, dual rangeSize - See table I3. SALIENT CHARACTERISTICS3.1 General requirements. The tester shall be so designed that a 30-degree si

5、de-load will notcause any deviation in the torque reading.3.1.1 Type I torque wrench tester. The type I torque wrench tester shall be a single station testermeeting the torque capacity of the applicable size shown in table I and the requirements specifiedherein.3.1.2 Type II torque wrench tester. Th

6、e type II torque wrench tester shall be a dual station testermeeting the torque capacity of the applicable size shown in table I and the requirements specifiedherein.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-593092TABLE I. Product classific

7、ations.Size Type Torque Range Dial Increment(maximum)Drive Size(male)1 I 0 - 250 inch-pounds 0.25 inch-pound 1/2-inch square2 0 - 2000 inch-pounds 2 inch-pounds 1/2-inch square3 0 - 1000 foot-pounds 1 foot-pound 1-inch square4Single station,single range 0 - 2000 foot-pounds 2 foot-pounds 1-inch squa

8、re5 II 0 - 50 inch-pounds0 - 800 inch-ounces0.1 inch-pound1 inch-ounce1/4-inch hexagon6 0 - 200 foot-pounds0 - 2400 inch-pounds0.2 foot-pound2.5 inch-pounds1/2-inch square7Single station,single range,dual scale 0 - 500 foot-pounds0 - 6000 inch-pounds1 foot-pound6 inch-pounds3/4-inch squareIII8 1/4-i

9、nch hexagon0 - 100 inch-ounces0 - 500 inch-ounces0.5 inch-ounce2.0 inch-ounces90 - 250 inch-pounds0 - 2000 inch-poundsSingle station,dual rangeordual station,dual range0.25 inch-pound2 inch-pounds 1/2-inch square3.1.3 Type III torque wrench tester. The type III torque wrench tester shall be a single

10、 station,dual range or dual station, dual range tester meeting the torque capacity of the applicable sizeshown in table I and the requirements specified herein.3.2 Components. The torque wrench tester shall include, as a minimum, the followingcomponents:3.2.1 Housing. The mechanism of the tester sha

11、ll be enclosed in a housing. The housing shallprovide a means for bolting the tester to a horizontal or vertical surface. If required (see 7.2(c),a conversion table shall be provided and attached to single scale testers to convert the dialreadings to other units of interest, such as foot-pounds to i

12、nch-pounds with the basic units andcoverage compatible with the tester as specified. Conversion tables shall be marked in apermanent manner on metal plates.3.2.2 Drive. Torque wrench tester shall be provided with a drive in accordance with theapplicable size listed in table I.3.2.3 Adapters. The tor

13、que wrench tester shall be provided with adapter(s) having femaleopenings on either end in accordance with the applicable size shown in table II.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-593093TABLE II. Adapter characteristics.Type Size Ada

14、pter1 1/2-inch female square to 1/4-inch female square1/2-inch female square to 3/8-inch female squareI 2 1/2-inch female square to 3/8-inch female double square1/2-inch female square to 1/2-inch female double square3 1-inch female square to 1-inch female square1-inch female square to 3/4-inch femal

15、e square4 1-inch female square to 1-inch female square5 1/4-inch female hex to 1/4-inch female square1/4-inch female hex to 3/8-inch female square6 1/2-inch female square to 1/2-inch female squareII1/2-inch female square to 3/8-inch female square3/4-inch female square to 3/4-inch female square73/4-i

16、nch female square to 1/2-inch female square1/4-inch female hex to 1/4-inch female double square81/4-inch female hex to 3/8-inch female double square1/4-inch female square to 1/4-inch female double square1/2-inch female square to 3/8-inch female double squareIII 91/2-inch female square to 1/2-inch fe

17、male double square3.2.4 Torque indicator. The torque wrench testers shall be provided with a dial indicator capableof displaying the torque applied to the drive. The dial indicator shall have a dial face, indicatingpointer, and protective cover. A means shall be provided for retaining the peak torqu

18、e applieduntil manually returned to zero. A zero adjustment shall be provided for the indicator and allscales. The dial increments shall not exceed those shown in table I for the applicable size.3.2.5 Calibration unit. When specified (see 7.2(d), the torque wrench tester shall be furnishedwith equip

19、ment for calibration by the dead weight method.3.3 Performance. Using an independently verified route traceable to National Institute ofStandards and Technology (NIST), the tester shall be accurate to within 1 percent of applied loadover the range from 20 percent of full scale to 100 percent of full

20、 scale. The torque wrench testersensitivity shall be sufficient to indicate any change in torque equal to 1/2 of a dial graduation. The torque wrench tester shall be capable of withstanding an overload condition of 20 percentbeyond maximum capacity without any degradation of accuracy.3.4 Systems of

21、units. The torque wrench tester shall be marked in U.S. Customary System(USCS) of units with a minimum space of not less than 0.020 inch between scale increments.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5930944. REGULATORY REQUIREMENTS4.1

22、Recovered materials. The offerer/contractor is encouraged to use recovered materials to themaximum extent practicable, in accordance with paragraph 23.403 of the Federal AcquisitionRegulation (FAR).4.2 Environmental protection. The item shall meet all applicable Environmental ProtectionAgency restri

23、ctions in effect on the date of the contract. These regulations apply to the emissionof materials hazardous to the environment or the users health and shall be adhered to during themanufacturing, service, transportation, storage, and operation/use of the item.5. QUALITY ASSURANCE PROVISIONS5.1 Produ

24、ct conformance. The products provided shall meet the salient characteristics of thiscommercial item description; conform to the producers own drawings, specifications, standards,and quality assurance practices; and be the same product as that which the supplier offers for saleon the commercial marke

25、t. The government reserves the right to require proof of suchconformance.5.1.1 Verification of conformance. The tester shall be calibrated by a method traceable to theNIST and shall be delivered with a calibration certificate or report.6. PACKAGING6.1 Preservation, packing and marking. For acquisiti

26、on purposes, the torque wrench testersupplied shall be preserved, packed, and marked as specified in the contract or order (see 7.2(e).7. NOTES7.1 Sources of documents7.1.1 FAR. The FAR may be obtained from the Superintendent of Documents, U.S. GovernmentPrinting Office, Washington, DC 20402-0001.7.

27、2 Ordering data. Acquisition documents must specify the following information:a. Title, number, and date of this documentb. Type and size of tester required (see 2)c. Conversion table, as specified (see 3.2.1)d. Calibration equipment, if required (see 3.2.5)e. Packaging requirements (see 6.1)Provide

28、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5930957.1 Part identification number (PIN). The following part identification numbering system is forgovernment purposes and does not constitute a requirement for the contractor.MILITARY INTERESTS:CIVIL AG

29、ENCYCOORDINATING ACTIVITY:Custodians:Air Force - 99Army - GLNavy - ASGSA - FCGCReviewers:Air Force - 82Army - AV, CENavy - MC, OSPreparing activity:DLA - GS(Project 6635-0177)Size: (see table I)Type: A - Type I Single station, single rangeB - Type II Dual station, single range, dual scaleC - Type III Single station, dual range or dual station, dual rangeAA59309 X XCID numberProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-