DLA A-A-59373-1999 NAVIGATOR-S PLOTTING INSTRUMENT SET AND CASE《领航测绘设备箱》.pdf

1、 W 9038054 0009333 LOT M INCH-POUND A-A-593 73 19 October 1999 SUPERSEDING 18 November 1977 MIL-N-634C COMMERCIAL ITEM DESCRIPTION NAVIGATORS PLOTTING INSTRUMENT SET AND CASE The General Services Administration has authorized the use of this commercial item description as a replacement for MIL-N-634

2、C for all federal agencies. 1. SCOPE. This commercial item description (CID) covers one type of plotting instrument set consisting of a storage case, a compass, a divider, a screwdriver, two additional leads, a complete additional set of needle points, one of each type and size of fastener used to s

3、ecure the leads and needle points, and a vial for containing the additional leads, needles and fasteners. 2. SALIENT CHARACTERISTICS 2.1 ComDonents. The set shall contain a case, compass, a divider, a screwdriver, two additional leads, a complete additional set of needle points. one of each type and

4、 size of fastener used to secure the leads and needle points, and a vial for containing the additional leads, needles and fasteners. 2. i. i Comnass. The compass shall be corrosion-resistant. The compass length shall be a minimum of 5- 112 inches and a maximum of 6- 112 inches, measured from center

5、of pivot end of legs. exclusive of lead or needle point. The needle point shall be held by a corrosion-resistant device that allows the point to pivot on the leg. The needle shall be reversible and replaceable in its carrier. Points shall have an ordinary needle point on one end and a short point wi

6、th a shoulder on the opposite end to limit the entering depth of the point. The pencil lead shaii be held in place by a corrosion-resistant device affned to the leg. With lead and needle points extended one- quarter inch from the ends of their legs, the compass will close the points to within one-th

7、irty- second of an inch of each other. A corrosion-resistant, straightening device shall be fitted to keep the head centered and up with reference to the legs (bisecting the angle of the legs) of the instrument and provide equal and simultaneous movement of each lead during adjustment. The Beneficia

8、l comments, recommendations, additions, deletions, clarifications, etc. and any other data which may improve this document should be sent to: Defense Supply Center Richmond (DSCR), ATTN: DSCR-VBD, 8000 Jefferson Davis Highway, Richmond, VA 23297-561 O. AMSC NIA FSC 6675 DISTRIBUTION STATEMENT A. App

9、roved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-H 9018054 0009332 046 A-A-59373 legs shall be attached at the pivot point by a friction joint that shall permit opening and closing with a smooth, un

10、iform, and continuous movement. Head construction shall be such that a locking device is not required. 2.1.2 Divider. The divider shail be identical to the compass (see 2.2.1), except that both legs shall be fitted to take reversible and replaceable steel needle points which shall be firmly held in

11、place by fasteners. 2.1.3 Needle Doints. screw studs. and insert lups. Needle points and holding device shall be made of corrosion-resistant steel. 2.1.4 Lead and needle point holder. The extra lead, needle points and fasteners shall be stored in a corrosion-resistant holder with a removable top. 2.

12、2 Instrument and case markings. 2.2.1 Instruments. Each compass and divider shall be marked in a plain and permanent manner with manufacturers name or identifiing trademark. 2.2.2 W. The case shall not exceed 8 inches long, 3 inches wide, and 1 inch high. The case shall have a permanently attached c

13、over to protect the instruments and accessories and shall provide a means of securing them inside the case. The case shall be lined with a non-abrasive cushioning material and the case fasteners shall be corrosion-resistant. The top flap or lid of the case shall have the following notation embossed

14、in a contrasting color in the center on the outside surface: a. Navigators Plotting Instrument Set b. National Stock Number c. Manufacturers Name d. Specification or Contract Number and Year e. U.S. 3. REGULATORY REQUIREMENTS 3.1 Recovered materials. The offerorkontractor is encouraged to use recove

15、red materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. QUALITY ASSURANCE PROVISIONS 4.1 Product conformance. The product provided shall meet the salient characteristics of this commercial item description; conform to the p

16、roducers own drawings, specifications, standards, and quality assurance practices; and be the same product as that which the supplier offers for sale on the commercial market. The government reserves the right to require proof of such conformance. 2 Provided by IHSNot for ResaleNo reproduction or ne

17、tworking permitted without license from IHS-,-,- II 7038054 0009333 T82 4.2 Market accePtability. The product offered shall be of the latest model of the standard product of the supplier and have been used in the field for at least one year by commercial organizations. 5. PACKAGING 5.1 Preservation.

18、 Dackinn. and marking. For acquisition purposes, the products shall be preserved, packed, and marked as specified in the acquisition order (see 6.4(c). 6. NOTES 6. I Sources of documents. 6.1.1 m. The FAR may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washingt

19、on, DC 20402-0001. 6.2 National stock number NSN). The following NSNs correspond to this CID. These may not be indicative of all possible NSNs associated with this document. 6675-00-240- 1876 6675-00-243-50 15 6675-00-285-61 6 1 6675-00-286-0602 6.3 Sources of supply. The manufacturers and/or suppli

20、ers listed below are known to supply products vhich meet the salient characteristics requirements of this document. Competition is not limited to the listed firms. Vane Brothers Company 4209 Newgate Avenue Baltimore, MD 2 1224-64 16 Weems and Plath Incorporated 222 Severn Avenue Annapolis, MD 2 1403

21、-253 1 1-888-33 1-5 167 1-410-263-6700 Dresser Argus Incorporated 36 Bridge Street Brooklyn NY 11201-1 115 1-718-643-1540 6.4 Ordering data. Acquisition documents must speciQ the following information: a. b. C. Title, number, and date of this document Unit and quantity required Packaging requirement

22、s (see 5.1) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A- A- 59 3 7 3 MILITARY INTERESTS: Custodians: Air Force - 99 Navy - SH Army - CR4 Reviewer: Navy - AS m 9018054 0009334 919 D CIVIL AGENCY COORDINATING ACTIVITY: GSA - FCGC Preparing activity: (Project 6675-0086) DLA - GS 1 I 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-