DLA A-A-59462-2000 INDICATOR SIGHT LIQUID REFRIGERANT [Superseded DLA MIL-I-23208 A CANC NOTICE 3 DLA MIL-I-23208 A VALID NOTICE 2 DLA MIL-I-23208 A NOTICE 1 DLA MIL-I-23208 A (1) .pdf

1、 INCH-POUND A-A-59462 3 1 January 2000 SUPERSEDING 24 May 1965 MIL-I-23208A COMMERCIAL ITEM DESCRIPTION INDICATOR, SIGHT, LIQUID, REFRIGERANT The General Services Administration has authorized the use of this commercial item description as a replacement for MIL-I-23208A for all federal agencies. 1.

2、SCOPE. This commercial item description (CID) covers liquid refrigerant sight flow indicators intended for use in systems using refrigerant type 12 or 22. 2. CLASSIFICATION. The indicators shall be of the following types and sizes. The type and size to be furnished shall be as specified (see 7.2(b).

3、 Type I - External flare connection SAE Male Flare end Size 1 - 1/4-inch connection Size 2 - 3/8-inch connection Size 3 - 1/2-inch connection Size 4 - 5/8-inch connection - External flare connection SAE hde - Female Flare en( Size 1 - 1/4-inch connection Size 2 - 3/8-inch connection Size 3 - 1/2-inc

4、h connection Size 4 - 5/8-inch connection Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any other data which may improve this document should be sent to Defense Supply Center Richmond (DSCR), ATTN: DSCR-VBD, 8000 Jefferson Davis Highway, Richmond, VA 23297-56 1

5、 O. AMSC N/A FSC 6680 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Licensed by Information Handling ServicesA-A-59462 Type III- Sweat joint connection end Size 1 - 1/4-inch connection Size 2 - 3/8-inch connection Size 3 - 1/2-inch connection Size 4 - 5/8-inch con

6、nection Size 5 - 7/8-inch connection Size 6 - 1 1/8-inch connection Size 7 - 1 3/8-inch connection Size 8 - 1 5/8-inch connection Size 9 - 2 1/8-inch connection 3. SALIENT CHARACTERISTICS 3.1 General requirements The indicator shall allow an unrestricted flow of refrigerant type 12 and 22 and shall

7、be certified in accordance with Underwriters Laboratories, Inc. (UL) 207, “Refrigerant-Containing Components and Accessories,Nonelectrical“ . The indicator shall contain not less than 0.24 square inches of unrestricted viewing area. 3.2 Moisture indicating element When required (see 7.2(c), a moistu

8、re indicating element shall be provided for determination of a wet or dry refrigerant. A color comparison code or chart for refrigerant type 12 and type 22 shall accompany the indicator. 4. REGULATORY REQUIREMENTS 4.1 Recovered materials The offeror/contractor is encouraged to use recovered material

9、s to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4.2 Environmental protection The sight glass shall meet all applicable Environmental Protection Agency (EPA) restrictions in effect on the date of the contract. These regulations app

10、ly to the emission of materials hazardous to the environment or the users health and shall be adhered to during the manufachiring, service, transportation, storage, and operatioduse of the sight glass. 5. QUALITY ASSURANCE PROVISIONS 5.1 Product conformance. The sight glasses shall meet the salient

11、characteristics of this CID; conform to the manufacturers own drawings, specifications, standards, and quality assurance practices; and be the same product offered for sale in the commercial market. The Government reserves the right to require proof of such conformance. 2 Licensed by Information Han

12、dling ServicesA-A-59462 5.1.1 Verification of conformance Verification of conformance to UL 207 shall be either the manufacturers standard certification of such conformance or by an accredited testing laboratory satisfactory to the Government. 5.1.2 Moisture element test. Each refrigerant shall have

13、 a maximum of 10 parts per million$m) moisture content when passed through and the indicating element shall indicate dry in accordance with the manufacturer3 established code or chart. The moisture content shall be gradually increased to a maximum of 40ppm. The element shall show a definite change t

14、o a wet condition. An intermediate change in the element shall be observed if manufacturer3 design requires. The manufacturer3 standard method for determining the moisture content of the refrigerant shall be acceptable. 6. PACKAGING 6.1 Preservation, packing, and marking For acquisition purposes, th

15、e indicators shall be preserved, packed, and marked as specified in the acquisition order (see 7.5(d). 7. NOTES 7.1 Sources of documents. 7.1.1 &R. The FAR may be obtained from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402-000 1. 7.1.2 UL standards. Copies of

16、 UL standards may be obtained from Underwriters Laboratories Inc., 333 Pfingsten Road, Northbrook, IL 60062. 7.2 Ordering data. Acquisition documents must specify the following: a. Title, number, and date of this document b. Type and size of indicator as required in contract (see 2) c. Moisture indi

17、cator, if required in contract (see 3.2) d. Packaging requirements, as specified (see 6.1) 3 Licensed by Information Handling ServicesA-A-59462 7.3 Part identification number (PIN) The following pait identification numbering procedure is for government purposes and does not constitute a requirement

18、for the contractor. AA59462 - :X _ Size: 1 - 114 inch connection 2 - 3/8 inch connection 3 - 1/2 inch connection 4 - 5/8 inch connection 5 - 7/8 inch connection 6 - 1 1/8 inch connection 7 - 1 3/8 inch connection 8 - 1 5/8 inch connection 9 - 2 1/8 inch connection Type: A - Type I, External flare co

19、nnection SAE Male Flare end B - Type II, External flare connection SAE Male - Female C - Type III, Sweat joint connection Flare end I CIDnumber MILITARY INTERESTS: Custodians: Navy - YD Air Force - 11 Army - GL Reviewers: Navy - MC, SH CIVIL AGENCY COORDINATING ACTIVITY: GSA - 7FXE Preparing activity: DLA - GS (Project 6680-0252) 4 Licensed by Information Handling Services