DLA A-A-59495-1999 GLOVES WOMEN-S (SUPERSEDES MIL-G-1007) [Superseded DLA MIL-G-1007 H CANC NOTICE 1 DLA MIL-G-1007 H CANC NOTICE 1 DLA MIL-G-1007 H INT AMD 1 DLA MIL-G-1007 H DLA .pdf

1、 INCH/POUNDA-A-59495Sept.15,1999SUPERSEDINGMIL-G-1007H14 October 1988COMMERCIAL ITEM DESCRIPTIONGLOVES, WOMENSThe General Services Administration has authorized the use ofthis commercial item description as a replacement for MIL-G-1007for all Federal agencies.1 SCOPE This document covers womens dres

2、s white glove intendedfor use by female military personnel of the Department ofDefense.2. CLASSIFICATION. Not applicable3. SALIENT CHARACTERISTICS. The gloves shall be a slip-on typewith a Bolton thumb made with a knitted nylon fabric.Beneficial comments, recommendations, additions, deletions,clarif

3、ications, etc. and any data which may improve this documentshould be sent to: Defense Supply Center Philadelphia, Clothingand Textiles Directorate, Attn: DPSC-COCT, 700 Robbins Avenue,Philadelphia, PA 19111-5096.AMSC N/A FSC 8445Provided by IHSNot for ResaleNo reproduction or networking permitted wi

4、thout license from IHS-,-,-A-A-5949523.1 Materials.3.1.1 The basic material shall be a nylon simplex jersey clothand may have a fluorescent optical brightener added. The finishedcloth shall have a smooth sueded finish on both sides of thematerial. The fully heat set cloth shall conform to therequire

5、ments cited below.Characteristic Requirements Test method Discoloration (light) 3 AATCC-16 1/ Weight (oz./sq. yard) 5.5-8.0 ASTM D 3776 2/ (min/max) Wales per inch (min.) 52 ASTM D 3887 Courses per inch (min.) 40 ASTM D 3887 Bursting Strength 100 ASTM D 3787(pounds min.)Dimensional stability AATCC 9

6、6 3/ (percent shrinkage)Length (max) 10 Nonfibrous Material 2.0 ASTM D 629pH (min/max) 5.0-8.5 ASTM-D-21651/ Option A2/ Option C3/ Option 1c for wash and Option D for dry3.1.2 Yarn. The yarn shall be a semi-dull or dull,multifilament nylon.3.1.3 Color. The color shall be white 3059 in accordance wit

7、hFED-STD - 595.3.1.4 Thread. The thread for seaming and stitching the gloveshall be a 2 ply cotton covered polyester having a size rangebetween 31 and 35(Tex).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-594953Sizes and measurements. The finis

8、hed glove shall conform to thesizes and measurements below.Table I. Finished measurements (in inches)Size Overall Width Length from base of thumblength of palm to top edge of glove(A) (B) (C)6 9-5/8 2-3/4 2-1/26-1/2 9-13/16 2-7/8 2-1/27 10 3 2-1/27-1/2 10-3/16 3-1/8 2-1/28 10-3/8 3-1/4 2-1/28-1/2 10

9、-9/16 3-3/8 2-1/29 10-3/4 3-1/2 2-1/2Tolerance (+3/16) (+1/8) (+1/8)NOTE: Refer to Figure 1 for A, B, and C.A. Measurement taken from the tip of middle finger to top edgeof glove.B. Measurement taken across palm, approximately 1/4 inch belowthe crotch of the fourth (little) finger.C. Measurement tak

10、en from the base of the thumb to top edge ofglove.3.2 Labels. A commercial-type label is acceptable, provided thatan additional printed cloth label containing the contractorsname, contract number, size and National Stock Number (NSN) iscaught on the stitching of the commercial label. The commerciall

11、abel shall include fiber and laundering information. (see ASTM D3951.)3.3 Label/tag. Each item shall be individually bar-coded with apaper tag for personal clothing items. The paper tag shall bestandard bleached sulfate having a basis weight of 100 pounds.The paper used for the tags shall have a smo

12、oth finish to acceptthermal transfer and direct printing. The tags shall have a holeand shall be attached to each item by a fastener, clearly legibleand readable by a scanner. The bar coding element shall be a 13digit national stock number (NSN). The bar code type shall be amedium to high code densi

13、ty and shall be located so that it iscompletely visible on the item when it is folded and/or packagedas specified and so that it causes no damage to the item.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5949544. REGULATORY REQUIREMENTS Recycle

14、d, recovered, orenvironmentally preferable materials should be used to themaximum extent possible provided that the material meets orexceeds the operational and maintenance requirements, andpromotes economically advantageous life cycle costs.5. QUALITY ASSURANCE PROVISIONS5.1 Product conformance. Th

15、e products provided shall meet thesalient characteristics of this commercial item description andshall conform to the producers own drawings, specifications,standards, and quality assurance practices. The Governmentreserves the right to require proof of such conformance.5.2 Visual examination. Each

16、glove shall be examined for thedefects listed below.Defects. Any hole, cut, or tear; color not as specified; anypart shaded; any spot or stain (outside); raw edges, open seams,thread ends not removed, or loose tension resulting in looseseams; any material defects, distorted parts or poor workmanship

17、;any component part omitted; label missing, incorrect, orillegible; measurement of item not as specified; bar code omittedor not readable by scanner; human-readable interpretation (HRI)omitted or illegible; bar code not visible on folded, packageditem; bar code causes damage to the item; any items n

18、ot packagedin accordance with the contract or purchase order. (Up to 3needle holes are acceptable).5.3 Dimensional examination. The gloves shall be measured and incompliance with the figures stated in Table I.5.4 Acceptance criteria. Acceptance criteria shall be asspecified in the contract or purcha

19、se order.6. PACKAGING The preservation, packing, and marking shall be asspecified in the contract or order.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5949557. NOTES7.1 Source of Government documents. Copies of military andFederal documents a

20、re available from:Standardization Documents Order DeskBldg. 4D700 Robbins AvenuePhiladelphia, PA 19111-50947.2 Source of non-Government documentsASTM Test Methods(Applications for copies should be addressed to AmericanSociety For Testing and Materials, 100 Bar Harbor Drive, WestConshohocken, PA, 194

21、28-2959).AATCC Test Method(Applications for copies should be addressed to AmericanAssociation of Textile Chemists and Colorists (AATCC), P.O. Box12215, Triangle Park, NC 27709-2215.)7.3 Titles of Non-Government test methodsAATCC 16 Colorfastness to lightASTM D 3776 Mass Per Unit Area (Weight) of Fab

22、ricASTM D 3887 Standard Specification for Tolerances for Knittedknitted FabricsASTM D 3787 Bursting Strength of Knitted GoodsAATCC 96 Dimensional Changes in Commercial Laundering ofWoven and Knitted Fabrics Except WoolASTM D 629 Quantitative Analysis of TextilesASTM D 2165 pH of Aqueous Extracts of

23、Wool and Similar AnimalFibersASTM D 3951 Standard Practice for Commercial Packaging7.4 Sources that could be used but not limited to, are asfollows:a. Glamor Glove Co.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-594956MILITARY INTERESTS:Custod

24、ians CIVIL AGENCY COORDINATINGArmy - GL ACTIVITY:Navy - NU GSA - FSSAir Force - 11Review Activities PREPARING ACTIVITY:Navy - CG DLA - CTArmy - MDAir Force - 99, 82Air Force - 45 Project 8445-0144Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59

25、4957FIGURE 1 GLOVES,WOMENSProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSAL INSTRUCTIONS 1. The preparing activity must complete blocks 1, 2, 3, and 8. In block 1, both the document number and revision lett

26、er should be given. 2. The submitter of this form must complete blocks 4, 5, 6, and 7, and send to preparing activity. 3. The preparing activity must provide a reply within 30 days from receipt of the form. NOTE: This form may not be used to request copies of documents, nor to request waivers, or cl

27、arification of requirements on current contracts. Comments submitted on this form do not constitute or imply authorization to waive any portion of the referenced document(s) or to amend contractual requirements. I RECOMMEND A CHANGE: 1. DOCUMENT NUMBER A-A-59495 2. DOCUMENT DATE (Y YYYMMDD) 19990915

28、 3. DOCUMENT TITLE GLOVES, WOMENS 4. NATURE OF CHANGE (Identify paragraph number and include proposed rewrite, if possible. Attach extra sheets as needed.) 5. REASON FOR RECOMMENDATION 6. SUBMITTER a. NAME (Last, First, Middle Initial) b. ORGANIZATION c. ADDRESS (Include Zip Code) d. TELEPHONE (Incl

29、ude Area Code) (1) Commercial (2) AUTOVON (if applicable) 7.DATE SUBMITTED (YYYYMMDD) 8. PREPARING ACTIVITY a. NAME DEFENSE SUPPLY CENTER PHILADELPHIA DSCP-C b. TELEPHONE Include Area Code) (1) Commercial 215-737-5866 (2) AUTOVON 444-5866 c. ADDRESS (Include Zip Code) 700 ROBBINS AVE (BLDG 6, C&T) P

30、HILADELPHIA, PA 19111-5092 IF YOU DO NOT RECEIVE A REPLY WITHIN 45 DAYS, CONTACT: Defense Standardization Program Office (DLSC-LM) 8725 John J. Kingman road, Suite 2533, Ft. Belvoir, VA 22060-2533 Telephone (703) 767-6888 AUTOVON 427-6888 DD Form 1426, FEB 1999 (EG) PREVIOUS EDITION IS OBSOLETE WHS/DIOR, Feb 99 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-