DLA A-A-59925-2013 BARBED TAPE HOOK (WIRE REINFORCED LONG BARB).pdf

1、 INCH-POUND A-A-59925 6 June 2013 COMMERCIAL ITEM DESCRIPTION BARBED TAPE, HOOK (WIRE REINFORCED LONG BARB) The General Services Administration has authorized the use of this Commercial Item Description for all Federal Agencies. 1. SCOPE. This Commercial Item Description (CID) covers hook barb tape

2、for barb tape entanglements. These entanglements may serve as a security barrier for confinement applications, nuclear generating plants, petroleum/chemical storage, refineries, sensitive areas at airports and nuclear weapons storage, etc. 2. SALIENT CHARACTERISTICS. 2.1 Material. The hook barbed ta

3、pe shall be made of material as specified below and shall be subject to all provisions of this CID: a. Barbed tape Stainless steel per ASTM A240/A240M, Type 430 or galvanized steel per ASTM A653/A653M. b. Core wire Stainless steel per ASTM A580/A580M, 300 Series, minimum tensile strength 140,000 psi

4、 or galvanized steel per ASTM A764, Finish 2, Class II, Type B minimum tensile strength 220,000 psi. 2.2 Design and construction. Hook barbed tape furnished under this CID shall conform to the dimensions and design characteristics as specified herein, in Figure 1 and in Table I. Single coil wire rei

5、nforced concertinas 19, 25 and 31 inch in diameter are to be fabricated from 0.025 inch thick AISI 430 stainless steel (SS) or ASTM A653/A563M galvanized steel (GA). Each roll shall consist of 31 or 51 coil loops with pair of loops alternately clipped together at 3 or 5 locations around the circumfe

6、rence dependent upon diameter. Concertina clip attachments shall be capable of withstanding a minimum pull load of 200 lbs. Clusters of 8 needle sharp barbs shall be located 4 inch on center along the spiral turns. The main barb length shall be 2.250 to 2.600 inch tip to tip, angled approximately 24

7、 degrees above the centerline of tape. The minor (retainer) barb shall be located 0.70 0.05 inch from the main barb tip and shall be 0.10 inch nominal length. Concertina coils are to be available in combinations of SS or GA tape and core wire. Barbed tape is to be wrapped 230 degrees around 0.098 in

8、ch diameter SS or GA core wire. Tape material (barb) shall be fabricated from SS or GA and is 1.375 inch wide prior to forming. FIGURE 1. BARBED TAPE. Comments, suggestions, or questions on this document should be addressed to Defense Supply Center Philadelphia, ATTN: DSCP-NASA, 700 Robbins Avenue,

9、Philadelphia, PA 19111-5096 or e-mail to dscpg&ispecommentsdla.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at https:/assist.dla.mil. ASMC N/A FSC 5660 Provided by IHSNot for ResaleNo reproduction or netwo

10、rking permitted without license from IHS-,-,-A-A-59925 2 TABLE I. Dash Numbers and Design Characteristics. Dash No. Description Dia. inch Coil Loops Strip Material Core Wire Clips Coil Spacing inch Yield feet Pkg. 1 Detainer Single Coil Concertina 19 31 SS GA 3 12 15 4/box 2 Detainer Single Coil Con

11、certina 19 31 GA GA 3 12 15 4/box 3 Detainer Single Coil Concertina 19 31 SS SS 3 12 15 4/box 4 Detainer Single Coil Concertina 25 31 SS GA 3 16 20 5/box 5 Detainer Single Coil Concertina 25 31 SS SS 3 16 20 5/box 6 Detainer Single Coil Concertina 31 51 SS GA 5 12 25 3/box 7 Detainer Single Coil Con

12、certina 31 51 SS SS 5 12 25 3/box 3. REGULATORY REQUIREMENTS. 3.1 The offerer/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation (FAR). 4. PRODUCT CONFORMANCE PROVISIONS. 4.1 Product conform

13、ance. The products provided shall meet the salient characteristics of this commercial item description, conform to the producers own drawings, specifications, standards, and the quality assurance practices, and be the same product offered for sale in the commercial market. The government reserves th

14、e right to require proof of such conformance. 5. PACKAGING. 5.1 Preservation, packing and marking shall be as specified in the contract or order. 6. NOTES. 6.1 Unless otherwise specified, all dimensions are in inches. 6.2 Unless otherwise specified in the contract or purchase order, packaging shall

15、be in accordance with ASTM D3951. 6.3 The following part or identification numbering procedure is for government purposes and does not constitute a requirement for the contractors. The part number identification number (PIN) shall consist of the basic commercial item description number followed by a

16、 dash number from Table I. Example: AA59925 - 6 Dash number Basic number 6.4 Source of documents. 6.4.1 FAR. The FAR may be obtained from the Regulatory Secretariat, 1800 F Street NW, Washington DC 20405 or online at http:/www.acqnet.gov. Provided by IHSNot for ResaleNo reproduction or networking pe

17、rmitted without license from IHS-,-,-A-A-59925 3 6.4.2 ASTM Standards. Copies of ASTM standards may be obtained from the ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or online at http:/www.astm.org. 6.5 Ordering data. The contract or order should specify the following:

18、 a. CID document number, revision, and CID PIN. b. Product conformance provisions. c. Packaging requirements. 6.6 Key words. Coil loops Entanglements Security Barrier MILITARY ACTIVITIES: CIVIL AGENCY COORDINATING ACTIVITY: GSA FAS Custodians: Army AT Preparing activity: Navy YD DLA IS Air Force 99

19、(Project 5660-2013-003) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-