DLA DESC-DWG-88022 REV E-2010 CAPACITORS FIXED ELECTROLYTIC POLARIZED ALUMINUM OXIDE SINGLE END MOUNTING.pdf

1、 REVISIONS LT DESCRIPTION DATE APPROVED A Added part number 88022-147. Updated manufacturers CAGE number. Editorial changes and corrections throughout. 24 Feb 1992 D Moore B Delete PIN 76 through PIN 147 and add PIN 148 through PIN 219. Correct operating temperature range for voltage above 100 volts

2、. Updated manufacturers CAGE number. Editorial changes and corrections throughout. 13 July 1998 M. Radecki C Add table showing substitution of newer parts for old canceled parts. 11 Dec 00 K. Cottongim D Update for 5 year review. 6 Oct 2009 Michael A. Radecki E Correction to 3.1.2 on capacitor end s

3、eal 27 Jan 2010 Michael A. Radecki Prepared in accordance with ASME Y 14.100 Source control drawing REV PAGE REV PAGE REV STATUS OF PAGES REV E E E E E E E E E E E E E E PAGES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Robert E. Grillot DESIGN ACTIVITY DEFENSE ELECTRONICS SUPPLY CENTER DA

4、YTON, OH 45444-5000 Original date of drawing CHECKED BY Edward H. Back TITLE CAPACITORS, FIXED, ELECTROLYTIC, POLARIZED, ALUMINUM OXIDE, SINGLE END MOUNTING 2 March 1988 APPROVED BY David E. Moore SIZE A CODE IDENT. NO. 14933 DWG NO. 88022 REV E PAGE 1 OF 14 AMSC 5910-E461 DISTRIBUTION STATEMENT A.

5、Approved for public release; distribution is unlimited.CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 PINSS 88022-76 THROUGH 88022-147 ARE CANCELED AFTER 13 JULY 1998. SEE TABLE III FOR SUBSTITUTABLE DATA. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DES

6、IGN ACTIVITY DEFENSE ELECTRONIC SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 88022 REV E PAGE 2 1. SCOPE 1.1 Scope. This drawing and MIL-PRF-39018 describes the complete requirements for aluminum oxide, electrolytic capacitors. 1.2 Part or Identifying Number (PIN). The co

7、mplete PIN shall be as follows: 88022 - XXXX Drawing number Dash number (see table I) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein.

8、Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract (see 6.2). DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-39018 - Capacitors, Fixed, Electrolytic (Aluminum Oxide), Established Reliability and Non-Established Reliability, General Specification fo

9、r. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-202 - Test Methods Standard Electronics and Electrical Component Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or https:/assist.daps.dla.mil or fr

10、om the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, howe

11、ver, supersedes applicable laws and regulations unless a specific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESIGN ACTIVITY DEFENSE ELECTRONIC SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO.

12、 88022 REV E PAGE 3 3. REQUIREMENTS 3.1 Interface and physical dimensions. The interface and physical dimensions shall be as specified in MIL-PRF-39018 and herein (see figure 1). 3.1.1 Terminals. Terminals shall be solder-coated, solid wire leads (see figure 1). * 3.1.2 Case. Each capacitor shall be

13、 enclosed in a metal case, and shall be effectively sealed with an elastomer end seal which prevents leakage or excess evaporation of electrolyte. 3.1.3 Operating and storage temperature range. The operating and storage temperature range shall be -55C to +105C for capacitors rated up to 100 volts, a

14、nd -40C to +105C for capacitors rated greater than 100 volts. 3.1.4 Insulating sleeves. Insulating sleeves shall meet the requirements of MIL-PRF-39018. 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be in accordance with table I. 3.2.2 Dielectric. The dielectric shall

15、be aluminum oxide in accordance with MIL-PRF-39018. 3.2.3 Capacitance. Nominal capacitance shall be within -10 percent, +100 percent of the value shown in table I at +25C, measured at 120 Hz and 1.0 volt rms maximum. 3.2.4 Equivalent series resistance (ESR). Equivalent series resistance at 120 Hz an

16、d 20 kHz shall not exceed the values shown in table I when measured at +25C with a maximum of 1.0 volt rms applied. 3.2.5 DC leakage current CE. DC leakage current shall not exceed values determined from the equation I = 0.5 after a 15 minute application of rated dc working voltage with the capacito

17、r connected in series with 1,000 ohm resistor, except it need not be less than 4.0 uA. Where: I = Leakage current in (A) C = Rated capacitance (F) E = Rated dc voltage 3.2.6 Impedance. Impedance shall not exceed the value shown in table I when measured at +25C, at a frequency of 100 kHz. 3.2.7 RMS r

18、ipple current. Maximum limits at +85C, and at frequencies from 20 kHz to 100 kHz are shown in table I, for other temperatures, the +85C ripple rating must be multiplied by the applicable factor from figure 2. For frequencies below 100 kHz, the rated rms ripple current may be multiplied by the applic

19、able multiplier from figure 3. 3.2.8 Life. One hundred percent of rated voltage applied at +105C for 2,000 hours. 3.2.9 Reverse voltage. Reverse voltage shall be 1.5 volts maximum. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESIGN ACTIVITY DEFEN

20、SE ELECTRONIC SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 88022 REV E PAGE 4 3.3 Environmental characteristics. 3.3.1 Moisture resistance. Moisture resistance shall be in accordance with MIL-PRF-39018. 3.3.2 Altitude operation. The altitude operation shall not exceed 70,

21、000 feet above sea level. 3.3.3 Shelf life. Shelf life shall be ten years minimum at a maximum storage temperature of +40C. 3.4 Physical characteristics. 3.4.1 Shock (specified pulse). Capacitors shall be tested in accordance with method 213 of MIL-STD-202. The following details shall apply: a. Capa

22、citors shall be rigidly supported. b. Test condition G (50 g peak). c. Measurement and electrical loading during shock: DC rated voltage shall be applied to the capacitor during test. Observations shall also be made to determine intermittent contact, arcing, open- or short-circuiting. Detecting equi

23、pment shall be sufficiently sensitive to detect any interruption of 0.5 ms or greater duration. d. Examination after test: Capacitors shall be visually examined for evidence of arcing, breakdown, mechanical damage, and leakage of electrolyte. 3.4.2 Random vibration. Capacitors shall be tested in acc

24、ordance with method 214 of MIL-STD-202. The following details shall apply: a. Mounting: Body of the capacitor shall be rigidly supported. b. Test condition E of table 214-II. c. Duration and direction of motion: Four hours in each of two mutually perpendicular directions (total of eight hours) one p

25、arallel and the other perpendicular to the cylindrical axis. d. Measurements: During the last 30 minutes in each direction, an electrical measurement shall be made to determine intermittent contacts or open- or short-circuiting. Detecting equipment shall be sufficiently sensitive to detect any inter

26、ruption of 0.5 ms or greater duration. e. Examination after test: Capacitors shall be visually examined for mechanical damage and leakage of electrolyte. 3.4.3 Terminal strength. Terminals shall meet the twist and lead pull test requirements of MIL-PRF-39018. 3.5 Marking. Marking shall be in accorda

27、nce with MIL-STD-1285, except the PIN shall be as specified (see 1.2) with the manufacturers name or CAGE code and date code. 3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible p

28、rovided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.7 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an approved source of supply. 3.8 Workman

29、ship. Capacitors shall be uniform in quality and free from any defects that will affect life, serviceability, or appearance. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESIGN ACTIVITY DEFENSE ELECTRONIC SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE

30、A CODE IDENT NO. 14933 DWG NO. 88022 REV E PAGE 5 Case Polyester-film insulation Lead space code D L 0.015 (0.38) 0.062 (1.57) S 0.015 (0.38) GE GJ GL GP GS GT HE HJ HL HP HS HT JE JJ JL JP JS JT 0.760 (19.30) 1.140 (28.95) 0.760 (19.30) 1.640 (41.65) 0.760 (19.30) 2.140 (54.35) 0.760 (19.30) 2.640

31、(67.05) 0.760 (19.30) 3.140 (79.75) 0.760 (19.30) 3.640 (92.45) 0.885 (22.49) 1.140 (28.95) 0.885 (22.49) 1.640 (41.65) 0.885 (22.49) 2.140 (54.35) 0.885 (22.49) 2.640 (67.05) 0.885 (22.49) 3.140 (79.75) 0.885 (22.49) 3.640 (92.45) 1.010 (25.65) 1.140 (28.95) 1.010 (25.65) 1.640 (41.65) 1.010 (25.65

32、) 2.140 (54.35) 1.010 (25.65) 2.640 (67.05) 1.010 (25.65) 3.140 (79.75) 1.010 (25.65) 3.640 (92.45) 0.250 (6.35) 0.250 (6.35) 0.250 (6.35) 0.250 (6.35) 0.250 (6.35) 0.250 (6.35) 0.300 (7.62) 0.300 (7.62) 0.300 (7.62) 0.300 (7.62) 0.300 (7.62) 0.300 (7.62) 0.400 (10.16) 0.400 (10.16) 0.400 (10.16) 0.

33、400 (10.16) 0.400 (10.16) 0.400 (10.16) NOTES: 1. Dimensions are in inches, millimeters are in parentheses. 2. Metric equivalents are given for general information only. 3. L dimension includes polymer coated end seal. 4. Polyester insulating sleeve to be permanently fixed to aluminum case. 5. A low

34、 and indeterminate resistance exists between the cathode and metal case. 6. Number 18 AWG wire (.040 inch .002 inch (1.016 mm 0.051 mm). 7. Rolled center bead optional for units with L dimensions greater than 2.140 inches (54.4 mm). FIGURE 1. Case dimensions and configuration. Provided by IHSNot for

35、 ResaleNo reproduction or networking permitted without license from IHS-,-,-DESIGN ACTIVITY DEFENSE ELECTRONIC SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 88022 REV E PAGE 6 FIGURE 2. Ripple current-temperature derating factors. FIGURE 3. Ripple current-frequency deratin

36、g factors. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESIGN ACTIVITY DEFENSE ELECTRONIC SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 88022 REV E PAGE 7 4. VERIFICATION 4.1 Sampling and inspection. Qualification inspe

37、ction is not required. 4.2 Conformance inspection. 4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A, group B, and group C inspections of MIL-PRF-39018. 4.2.2 Certification. The acquiring activity, at its discretion, may accept a certificate of

38、 compliance with group B and group C requirements in lieu of performing group B and group C tests (see 6.2b). 4.2.3 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-PRF-39018. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as

39、 specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control

40、 Points packaging activity within the Military Service or Defense Agency, or within the military services system command. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packa

41、ging activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DESIGN ACTIVITY DEFENSE ELECTRONIC SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 88022 REV E PAGE 8 TABLE I Electrical characteristics. DSCC drawing 88022- 1/ F

42、 Maximum ESR in milliohms at 25C Maximum RMS ripple current in amperes at 20 kHz to 100 kHz and +85C Maximum impedance in milliohms at 100 kHz and 25C Case code 120 Hz 20 kHz 6.3 volts dc working, 9 V dc surge 001 1500 98 69 2.48 70 GE 002 2200 71 51 3.18 52 HE 003 5600 33 25 5.66 27 JJ 004 6800 23

43、18 7.40 19 GS 005 10000 19 15 8.85 17 HS 006 12000 19 15 8.86 17 JP 007 15000 15 13 10.20 14 JS 008 18000 14 12 11.40 13 JT 7.5 volts dc working, 10 V dc surge 009 1200 115 76 2.36 78 GE 010 1800 80 55 3.06 56 HE 011 2700 62 45 3.68 46 JE 012 3900 39 28 4.92 29 HJ 013 5600 28 20 6.50 22 HL 014 6800

44、23 17 7.70 19 HP 015 8200 23 18 7.41 19 JL 016 10000 19 15 8.86 16 JP 017 12000 17 13 10.20 14 JS 018 15000 14 12 11.40 13 JT 10 volts dc working, 14 V dc surge 019 2200 67 45 3.68 47 JE 020 3900 31 20 6.51 23 GP 021 4700 35 24 5.78 26 JJ 022 5600 22 15 8.20 18 HP 023 6800 23 16 7.86 19 JL 12 volts

45、dc working, 16 V dc surge 024 1000 126 76 2.36 79 GE 025 2200 68 43 3.77 45 JE 026 2700 41 25 5.31 27 GL 027 3300 45 29 4.84 31 HJ 028 4700 30 19 6.67 21 HL 029 6800 19 13 9.51 17 HS 030 8200 19 14 9.17 18 JP 031 10000 16 12 10.60 16 JS Provided by IHSNot for ResaleNo reproduction or networking perm

46、itted without license from IHS-,-,-DESIGN ACTIVITY DEFENSE ELECTRONIC SUPPLY CENTER, DAYTON, OH 45444-5000 SIZE A CODE IDENT NO. 14933 DWG NO. 88022 REV E PAGE 9 TABLE I Electrical characteristics- Continued. DSCC drawing 88022- 1/ F Maximum ESR in milliohms at 25C Maximum RMS ripple current in ampe

47、res at 20 kHz to 100 kHz and +85C Maximum impedance in milliohms at 100 kHz and 25C Case code 120 Hz 20 kHz 16 volts dc working, 20 V dc surge 032 820 142 78 2.33 80 GE 033 1500 86 51 3.18 53 HE 034 1800 74 46 3.64 48 JE 035 2700 47 28 4.92 30 HJ 036 3300 34 20 6.51 23 GP 037 3900 37 24 5.78 27 JJ 0

48、38 5600 25 17 7.62 20 JL 039 6800 20 13 9.51 17 JP 040 8200 17 12 10.60 16 JS 041 12000 15 10 12.40 14 JT 20 volts dc working, 30 V dc surge 042 680 131 72 2.42 75 GE 043 1000 86 50 3.21 54 HE 044 1500 71 43 3.68 45 JE 045 2200 44 26 5.11 28 HJ 046 2700 37 23 5.90 25 JJ 047 3300 30 19 6.67 21 HL 048 3900 24 15 8.69 18 GT 049 4700 26 17 7.62 20 JL 050 5600 20 14 9.17 17 JP 051 6800 17 12 10.60 16 JS 052 8200 15 10 12.40 14 JT 25 volts dc working, 35 V dc surge 053 560 144 67 2.51 70 GE 054 820 103 51 3.18 55 HE 055 1200 80 42 3.81 44 JE 056 1500 49 24 5.42 26 GL 057 1800 52 27 5.01 3