DLA DSCC-DWG-92001 REV C-2009 CAPACITORS FIXED ELECTROLYTIC DOUBLE LAYER SEALED.pdf

1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Correct vendor table, cage code and vendor address. 10 July 2000 Kendall Cottongim B Correct vendor part, table title and vendor address. 14 July 2003 Kendall Cottongim C Update for 5 year review, editorial corrections. 10 Nov 2009 Michael Radecki THE ORIGI

2、NAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. Prepared in accordance with ASME Y14.100 Source control drawing REV PAGE REV PAGE REV STATUS OF PAGES REV C C C C C C C C PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Robert Grillot DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing

3、6 January 1992 CHECKED BY Edward W. Back TITLE CAPACITORS, FIXED, ELECTROLYTIC, DOUBLE LAYER, SEALED APPROVED BY David E. Moore SIZE A CODE IDENT. NO. 14933 DWG NO. 92001 REV C PAGE 1 OF 8 AMSC N/A 5910-E432 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by

4、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 92001 REV C PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for fixed, electrolytic, double layer, sealed, high

5、-reliability capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 92001 | | XX | |Drawing Dash number _ number (see table I) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, a

6、nd handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are cited in the solicitation or contract. DEPARTMENT OF DEFENSE STANDARDS MIL-C-29501 - Capacitors, Fixed, Electrolytic, Double Layer, Carbon (Metric), General Specifi

7、cation for. MIL-STD-202 - Test Methods for Electronic and Electrical Components Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla/mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robins Aven

8、ue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a spe

9、cific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 92001 REV C PAGE 3 3. REQUIREMENTS 3.1 Interface and physical dimensions(see figure

10、1). . The interface and physical dimensions shall be as specified in MIL-C-29501 and herein 3.1.1 Case. The case shall be tantalum. 3.1.2 Leads. The leads shall be solder plated nickel (see figure 1). 3.1.3 Storage temperature. The storage temperature shall be -62C to +95C. Capacitors can be stored

11、uncharged for brief periods at temperatures up to +125C without permanent damage. 3.1.4 Operating temperature range. The operating temperature range shall be -55C to +85C. 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be in accordance with table I at -55C to +85C. 3.2.

12、2 Surge voltage. Surge voltage shall be in accordance with MIL-C-29501 with the following exceptions: a. The ambient temperature during cycling shall be +85C. b. Each cycle shall consist of 30 2 seconds surge voltage application followed by 30 2 seconds discharge period. 3.2.3 Dielectric. The dielec

13、tric shall be activated carbon and an aqueous electrolyte. 3.2.4 Voltage aging. Voltage aging shall be in accordance with MIL-C-29501, except at +85C. 3.2.5 DC leakage current. DC leakage current shall be measured in accordance with MIL-C-29501 and table I with the following exceptions: a. RC= 10 oh

14、ms. b. EO= Rated voltage 0.05 V dc. c. VR= Voltage drop by resistance RC24 0.5 hours after EOapplied. 3.2.6 Capacitance. Capacitance shall be in accordance with MIL-C-29501 with the following exception: EO= Rated voltage 0.05 V dc. 3.2.7 Capacitance tolerance. The capacitance tolerance shall be -20

15、percent, +80 percent at +25C. 3.2.8 Equivalent series resistance (ESR). Equivalent series resistance shall be in accordance with MIL-C-29501 and table I. 3.2.9 Stability at low and high temperatures. Stability at low and high temperatures shall be in accordance with MIL-C-29501 with the following ex

16、ceptions: a. Low test temperature -55C. b. High test temperature +85C. c. Thermal stability has been reached when no further change in ESR is observed between two successive measurements taken at intervals of 15 +2, -0 minutes. d. Step 2 - ESR shall not exceed 600 percent of the step 1 measured valu

17、e. e. Steps 2 and 4 - Capacitance shall change not more than 50 percent from the initial measured value. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 92001 REV C PA

18、GE 4 f. Step 5 - Capacitance shall change not more than 20 percent from the initial measured value. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. For D and H dimensions, see table I. Inches mm .002 0.05 .020 0.51 .025 0.64 .060 1.52 .400 10.16 .

19、475 12.07 .580 14.73 .620 15.75 .645 16.38 .650 16.51 .655 16.64 .675 17.15 .680 17.27 .795 20.19 .950 24.13 .975 24.77 1.030 26.16 1.035 26.29 1.045 26.54 1.050 26.67 1.070 27.18 1.100 27.94 1.280 32.51 1.500 38.10 1.600 40.64 Provided by IHSNot for ResaleNo reproduction or networking permitted wit

20、hout license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 92001 REV C PAGE 5 FIGURE 1. Case dimensions and configuration. TABLE I. Electrical characteristics. DSCC drawing 92001- Capacitance in farads 1/ Rated voltage dc Surge voltage dc ESR max (oh

21、ms) 1/ Leakage current max (A) 1/ CASE code Dimensions D .020 H .060 01 02 03 04 05 06 07 08 09 10 11 12 13 14 1.5 1.0 0.47 0.22 0.10 0.047 1.0 0.68 0.47 0.22 0.10 0.047 0.022 0.56 5.5 5.5 5.5 5.5 5.5 5.5 5.5 11.0 11.0 11.0 11.0 11.0 11.0 11.0 6.3 6.3 6.3 6.3 6.3 6.3 6.3 12.6 12.6 12.6 12.6 12.6 12.

22、6 12.6 0.5 0.7 1.5 3.0 6.0 12.0 2.0 1.0 1.5 3.0 6.0 12.0 24.0 4.0 50 35 25 12 6 3 25 50 35 25 12 6 3 25 A A A A A B A A A A A B B A 1.600 1.280 1.035 0.795 0.620 0.475 1.100 1.600 1.280 1.035 0.795 0.620 0.475 1.100 0.680 0.675 0.645 0.650 0.620 0.655 0.580 1.070 1.050 1.030 1.030 0.975 1.045 0.950

23、1/ Test temperature +25C 2C. 3.3 Environmental characteristics. 3.3.1 Thermal shock. Thermal shock shall be in accordance with MIL-C-29501. 3.3.2 Moisture resistance. Moisture resistance shall be in accordance with MIL-C-29501. 3.3.3 Seal test. Capacitors shall be tested in accordance with method 11

24、2 of MIL-STD-202, condition D. The following details and exception apply: a. Test condition letter D (except maximum temperature +85C florinert). b. Examination after test: not applicable. c. There shall be no evidence of leakage (bubbling). 3.3.4 Life. Life shall be in accordance with MIL-C-29501 w

25、ith the following exceptions: a. Test condition letter F (2000 hours). b. Test temperature +85C 2C. c. Measurements during exposure: DC leakage shall be measured as specified at 0; 240 +48, -0 hours, 500 +48, -0 hours, 1,000 +48, -0 hours and 2000 +48, -0 hours. The manufacturer may option to measur

26、e dc leakage at +85C; however; if the capacitors fail to meet the dc leakage requirement in 3.2.5, the measurement shall be made at +25C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT

27、 NO. 14933 DWG NO. 92001 REV C PAGE 6 3.4 Physical characteristics. 3.4.1 Shock (specified pulse)MIL-C-29501. . Capacitors shall be tested in accordance with method 213 of MIL-STD-202, limits as specified in 3.4.2 Vibration, high frequency. Vibration, high frequency shall be in accordance with MIL-C

28、-29501. 3.4.3 Resistance to solder heat. Resistance to solder heat shall be in accordance with MIL-C-29501 with the following exception: Test condition letter B. Procedure 1, leads shall be immersed to the depth of 0.050 inches from butt weld on anode lead. 3.4.4 Terminal strength. Terminal strength

29、 shall be in accordance with MIL-C-29501 with the following exceptions: a. Test condition letter A: The body of the capacitor shall be secured; 5 pounds applied force. b. Test condition letter (wire leads only) C: 5 pounds applied force; 3 bends. 3.4.5 Solderability. Solderability shall be in accord

30、ance with MIL-C-29501 with the following exception; Depth of immersion in flux and solder: All terminals shall be immersed to within 0.25 inches of the capacitor body. 3.4.6 Resistance to solvents. Resistance to solvents shall be in accordance with MIL-C-29501. 3.5 Recycled, recovered, or environmen

31、tally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advantageous life cycle costs. 3.6 Certificate of

32、 compliance. A certificate of compliance shall be required from manufacturers requesting to be a suggested source of supply. 3.7 Manufacturer eligibility. To be eligible for listing as an approved source of supply a manufacturer shall perform all testing specified herein on a sample of parts agreed

33、upon by the manufacturer and DSCC-VA. 3.8 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content of capacitor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3 percent lead, by mass

34、(see 6.3) 3.9 Marking. Marking shall be in accordance with MIL-STD-1285, except the (part name) shall be marked with the PIN as specified herein (see 1.2), the manufacturers name or Commercial and Government Entity (CAGE) code, and date lot codes. 3.10 Workmanship. The capacitor shall be uniform in

35、quality and free from any defects that will affect life, serviceability, or appearance. 4. VERIFICATION 4.1 Qualification inspection. Qualification inspection is not required. 4.2 Quality conformance inspections. 4.2.1 Inspection of product for delivery. All capacitor assemblies are seal tested in a

36、ccordance with MIL-STD-202, method 112, test condition D (except maximum temperature +85C). They are also checked for dc leakage, capacitance, and dissipation factor or ESR before being shipped. 4.2.2. Certification. The acquiring activity, as its discretion, may accept a certificate of compliance w

37、ith groups B and C requirements of MIL-C-29501 in lieu of performing groups B and C tests of MIL-C-29501 (see 6.2c). 4.2.3 Inspection of packaging. Inspection of packaging shall be in accordance with MIL-C-29501. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

38、om IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 92001 REV C PAGE 7 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of materiel is to be perfo

39、rmed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points packaging activity within the Military Department or Defense Agency, or within the Military D

40、epartments System Command. Packaging data retrieval is available from the managing Military Departments or Defense Agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature,

41、which may be helpful, but is not mandatory.) 6.1 Intended use. Capacitors covered by this drawing are intended mainly for use as a standby power source for low-power memories during power outages lasting up to several days. Since these capacitors have relatively high ESR (0.5 to 24 ohms), they are n

42、ot recommended for filtering applications. 6.2 Ordering data. The contract or purchase order should specify the following: a. Complete PIN (see 1.2). b. Requirements for delivery of one copy of the conformance inspection data or certificate of compliance that parts have passed conformance inspection

43、 with each shipment of parts by the manufacturer. c. Requirements for packaging and packing. d. Whether the manufacturer performs the group B inspections, or provides certification of compliance with group B inspections. e. Requirements for notification of change of product to procuring activity, if

44、 applicable. 6.3 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can develop under typical operating conditions, on products th

45、at use such materials. Conformal coatings applied over top of a whisker-prone surface will not prevent the formation of tin whiskers. 6.4 Replaceability. Capacitors covered by this drawing will replace the same commercial device covered by contractor prepared specification or drawing. 6.5 Similar ve

46、ndor PINs. See table II. 6.6 Users of record. Coordination of this document for future revisions is coordinated only with the approved sources of supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be achieved online at CapacitorFilterdla.mil

47、or if in writing to: Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0563 or DSN 850-0563. 6.7 Approved sources of supply. Approved sources of supply are listed herein. Additional sources will be added as they become available.

48、 Assistance in the use of this drawing may be obtained at CapacitorFilterdla.mil , or by contacting Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0563 or DSN 850-0563. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 92001 REV C PAGE 8 Table II. Similar vendor PIN. DSCC 92001- Vendor similar PIN 1/ 01