DLA DSCC-DWG-92001 REV C-2009 CAPACITORS FIXED ELECTROLYTIC DOUBLE LAYER SEALED.pdf
《DLA DSCC-DWG-92001 REV C-2009 CAPACITORS FIXED ELECTROLYTIC DOUBLE LAYER SEALED.pdf》由会员分享,可在线阅读,更多相关《DLA DSCC-DWG-92001 REV C-2009 CAPACITORS FIXED ELECTROLYTIC DOUBLE LAYER SEALED.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、 REVISIONS LTR DESCRIPTION DATE APPROVED A Correct vendor table, cage code and vendor address. 10 July 2000 Kendall Cottongim B Correct vendor part, table title and vendor address. 14 July 2003 Kendall Cottongim C Update for 5 year review, editorial corrections. 10 Nov 2009 Michael Radecki THE ORIGI
2、NAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. Prepared in accordance with ASME Y14.100 Source control drawing REV PAGE REV PAGE REV STATUS OF PAGES REV C C C C C C C C PAGES 1 2 3 4 5 6 7 8 PMIC N/A PREPARED BY Robert Grillot DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OH Original date of drawing
3、6 January 1992 CHECKED BY Edward W. Back TITLE CAPACITORS, FIXED, ELECTROLYTIC, DOUBLE LAYER, SEALED APPROVED BY David E. Moore SIZE A CODE IDENT. NO. 14933 DWG NO. 92001 REV C PAGE 1 OF 8 AMSC N/A 5910-E432 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by
4、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 92001 REV C PAGE 2 1. SCOPE 1.1 Scope. This drawing describes the requirements for fixed, electrolytic, double layer, sealed, high
5、-reliability capacitors. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as follows: 92001 | | XX | |Drawing Dash number _ number (see table I) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, a
6、nd handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are cited in the solicitation or contract. DEPARTMENT OF DEFENSE STANDARDS MIL-C-29501 - Capacitors, Fixed, Electrolytic, Double Layer, Carbon (Metric), General Specifi
7、cation for. MIL-STD-202 - Test Methods for Electronic and Electrical Components Parts. MIL-STD-1285 - Marking of Electrical and Electronic Parts. (Copies of these documents are available online at http:/assist.daps.dla/mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robins Aven
8、ue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a spe
9、cific exemption has been obtained. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 92001 REV C PAGE 3 3. REQUIREMENTS 3.1 Interface and physical dimensions(see figure
10、1). . The interface and physical dimensions shall be as specified in MIL-C-29501 and herein 3.1.1 Case. The case shall be tantalum. 3.1.2 Leads. The leads shall be solder plated nickel (see figure 1). 3.1.3 Storage temperature. The storage temperature shall be -62C to +95C. Capacitors can be stored
11、uncharged for brief periods at temperatures up to +125C without permanent damage. 3.1.4 Operating temperature range. The operating temperature range shall be -55C to +85C. 3.2 Electrical characteristics. 3.2.1 Rated voltage. The rated voltage shall be in accordance with table I at -55C to +85C. 3.2.
12、2 Surge voltage. Surge voltage shall be in accordance with MIL-C-29501 with the following exceptions: a. The ambient temperature during cycling shall be +85C. b. Each cycle shall consist of 30 2 seconds surge voltage application followed by 30 2 seconds discharge period. 3.2.3 Dielectric. The dielec
13、tric shall be activated carbon and an aqueous electrolyte. 3.2.4 Voltage aging. Voltage aging shall be in accordance with MIL-C-29501, except at +85C. 3.2.5 DC leakage current. DC leakage current shall be measured in accordance with MIL-C-29501 and table I with the following exceptions: a. RC= 10 oh
14、ms. b. EO= Rated voltage 0.05 V dc. c. VR= Voltage drop by resistance RC24 0.5 hours after EOapplied. 3.2.6 Capacitance. Capacitance shall be in accordance with MIL-C-29501 with the following exception: EO= Rated voltage 0.05 V dc. 3.2.7 Capacitance tolerance. The capacitance tolerance shall be -20
15、percent, +80 percent at +25C. 3.2.8 Equivalent series resistance (ESR). Equivalent series resistance shall be in accordance with MIL-C-29501 and table I. 3.2.9 Stability at low and high temperatures. Stability at low and high temperatures shall be in accordance with MIL-C-29501 with the following ex
16、ceptions: a. Low test temperature -55C. b. High test temperature +85C. c. Thermal stability has been reached when no further change in ESR is observed between two successive measurements taken at intervals of 15 +2, -0 minutes. d. Step 2 - ESR shall not exceed 600 percent of the step 1 measured valu
17、e. e. Steps 2 and 4 - Capacitance shall change not more than 50 percent from the initial measured value. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 92001 REV C PA
18、GE 4 f. Step 5 - Capacitance shall change not more than 20 percent from the initial measured value. NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. For D and H dimensions, see table I. Inches mm .002 0.05 .020 0.51 .025 0.64 .060 1.52 .400 10.16 .
19、475 12.07 .580 14.73 .620 15.75 .645 16.38 .650 16.51 .655 16.64 .675 17.15 .680 17.27 .795 20.19 .950 24.13 .975 24.77 1.030 26.16 1.035 26.29 1.045 26.54 1.050 26.67 1.070 27.18 1.100 27.94 1.280 32.51 1.500 38.10 1.600 40.64 Provided by IHSNot for ResaleNo reproduction or networking permitted wit
20、hout license from IHS-,-,-DEFENSE SUPPLY CENTER, COLUMBUS COLUMBUS, OHIO SIZE A CODE IDENT NO. 14933 DWG NO. 92001 REV C PAGE 5 FIGURE 1. Case dimensions and configuration. TABLE I. Electrical characteristics. DSCC drawing 92001- Capacitance in farads 1/ Rated voltage dc Surge voltage dc ESR max (oh
21、ms) 1/ Leakage current max (A) 1/ CASE code Dimensions D .020 H .060 01 02 03 04 05 06 07 08 09 10 11 12 13 14 1.5 1.0 0.47 0.22 0.10 0.047 1.0 0.68 0.47 0.22 0.10 0.047 0.022 0.56 5.5 5.5 5.5 5.5 5.5 5.5 5.5 11.0 11.0 11.0 11.0 11.0 11.0 11.0 6.3 6.3 6.3 6.3 6.3 6.3 6.3 12.6 12.6 12.6 12.6 12.6 12.
22、6 12.6 0.5 0.7 1.5 3.0 6.0 12.0 2.0 1.0 1.5 3.0 6.0 12.0 24.0 4.0 50 35 25 12 6 3 25 50 35 25 12 6 3 25 A A A A A B A A A A A B B A 1.600 1.280 1.035 0.795 0.620 0.475 1.100 1.600 1.280 1.035 0.795 0.620 0.475 1.100 0.680 0.675 0.645 0.650 0.620 0.655 0.580 1.070 1.050 1.030 1.030 0.975 1.045 0.950
23、1/ Test temperature +25C 2C. 3.3 Environmental characteristics. 3.3.1 Thermal shock. Thermal shock shall be in accordance with MIL-C-29501. 3.3.2 Moisture resistance. Moisture resistance shall be in accordance with MIL-C-29501. 3.3.3 Seal test. Capacitors shall be tested in accordance with method 11
24、2 of MIL-STD-202, condition D. The following details and exception apply: a. Test condition letter D (except maximum temperature +85C florinert). b. Examination after test: not applicable. c. There shall be no evidence of leakage (bubbling). 3.3.4 Life. Life shall be in accordance with MIL-C-29501 w
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- DLADSCCDWG92001REVC2009CAPACITORSFIXEDELECTROLYTICDOUBLELAYERSEALEDPDF

链接地址:http://www.mydoc123.com/p-688956.html