DLA MIL-B-18 250 B-2010 BATTERY DRY BA-399 U.pdf

1、AMSC N/A FSC 6135 INCH-POUND MIL-B-18/250B 22 November 2010 SUPERSEDING MIL-B-18/250A (ER) 28 May 1985 MILITARY SPECIFICATION SHEET BATTERY, DRY, BA-399/U This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product d

2、escribed herein shall consist of this specification sheet and MIL-B-18. FIGURE 1. Battery dimensions. INACTIVE FOR NEW DESIGN AFTER 10 AUGUST 1998 AND IS NO LONGER USED, EXCEPT FOR REPLACEMENT PURPOSES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,

3、-MIL-B-18/250B 2 Ltr Inches mm Min Max Min Max A .562 .625 14.27 15.88 B .450 .563 11.43 14.30 C .250 .313 6.35 7.95 D .562 .625 14.27 15.88 E .255 .270 6.48 6.86 F .056 .111 1.42 2.82 G .219 .229 5.56 5.82 H .323 .378 8.20 9.60 J 1.875 1.938 47.63 49.23 K .437 .500 11.10 12.70 L 3.062 3.125 77.77 7

4、9.38 M .875 1.001 22.23 25.43 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information only. 3. Four holes to fit .094 inch (2.38 mm) pins. 4. Socket inset contacts are not required. 5. Socket opening in a non metallic jacket shall coincide with outer edge of batte

5、ry on side shown. FIGURE 1. Battery dimensions - Continued. REQUIREMENTS: Dimensions, marking, and configuration: See figure 1. Nominal voltage: 15.0 volts. Usual number and type of cells: 10 “R” cells. Usual cell connection: Series. Terminals: 4-hole socket. Weight (maximum): 6.0 ounces. Capacity t

6、ests: When the battery is tested in accordance with the methods of examination and test of this specification, the minimum capacity-test requirements shall be not less than the minimum time specified for SLD or SLT. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

7、 from IHS-,-,-MIL-B-18/250B 3 First article inspection in accordance with MIL-B-18: Visual and mechanical (external). Battery voltage. Vibration test. Mechanical-shock test in accordance with MIL-STD-202, method 213, test condition I. Insulation resistance test in accordance with MIL-STD-202, method

8、 302, test condition B, tolerance 20 volts. Capacity, D (without storage). Jacket integrity test. Conformance inspection in accordance with MIL-B-18: Visual and mechanical (external). Battery voltage. Insulation resistance test in accordance with MIL-STD-202, method 302, test condition B, tolerance

9、20 volts. Vibration test. Mechanical-shock test in accordance with MIL-STD-202, method 213, test condition I. Jacket integrity test. Electrode leakage. Capacity, D and T. Method of examination and test: Capacity tests: See requirements for capacity specified herein. Storage: Test Period D 12 months

10、T 90 days Discharge: The battery shall be discharged through a resistance of 100 ohms for 2 minutes, then remain on open circuit for 28 minutes. This cycle shall be repeated 5 days per week continuously to a test-end voltage of 10.0 volts. Special marking on each unit package: TO TEST THIS BATTERY W

11、ITH TS-183 ( )/U: USE JACK NO. MINIMUM PERMISSIBLE VOLTAGE 13 13.8 Unless expressly authorized, this test information shall apply to Army and Air Force applications only. Part or Identifying Number (PIN): BA-399/U, see 1.2 of MIL-B-18. Reference documents. In addition to MIL-B-18, this document refe

12、rences the following: MIL-STD-202 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-18/250B 4 The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a conveni

13、ence only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Cu

14、stodians: Preparing activity: Army - CR DLA - CC DLA - CC (Project 6135-2010-064) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-