DLA MIL-C-16775 D-1989 CHESTS FIELD ALUMINUM EMPTY [Use In Lieu Of DLA MIL-C-0016775 C]《野外用空铝箱》.pdf

1、3. *- s 1. SCOPE MIL-C-lb775D b5 m 7999906 0259022 5 I INCH/POUND I MIL-C-16775D 12 June 1989 SUPERSEDING MIL-C-0016775C (DM) 8 March 1965 MILITARY SPECIFICATION CHESTS, FIELD, ALUMINUM, EMPTY This specification is approved for use by all Departments and Agencies of the Department of Defense. 1.1 Sc

2、ope. This.specification covers the standard series of deep drawn, empty, lightweight, aluminum field chests, composed of standardized elements as hereinafter specified. Chests shall be suitable for the safe transportation of medical material under field conditions in any global environmental conditi

3、ons without additional outer packaging or crating. 1.2 Classification. Chests shall be furnished as specified for the appropriate stock number and item identification as specified in the contract. Table I identifies the size and nominal inner dimensions. O l I I Beneficial comments (recommendations,

4、 additions, deletions) l I and any pertinent data which may be of use in improving this I I document should be addressed to: Defense Personnel Support I I Center, Directorate of Medical Materiel, DPSC-RST, 2800 South I I addressed Standardization Document Improvement Proposal (DD I I Form 1426) appe

5、aring at the end of this document or by 1etter.l I 20th Street, Philadelphia, PA 19101, by using the self- I I I AMSC/NA FSC 6545 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. , . THIS DOCUMENT CONTAINS /di/ PAGES. Licensed by Information Handling ServicesProvided

6、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - MIL-C-Lb775D b5 m 7777706 0257023 7 I MIL-C-16775D TABLE I. Size and dimensions. I Size I Dimensions (inches) I I I Length I Width I Depth I I I I I 1 1 i 24-1/4 i 12-/4 i 6-1/4 2 1 30-1/4 I 18-1/4 I 6-1/4 3

7、 I 30-1/4 I 18-1/4 I 10-1/4 I I I 4 I 30-1/4 I 18-1/4 1 12-1/4 I 5 I 30-1/4 I 18-1/4 I 16-1/4 I 6 I 30-1/4 I 18-1./4 I 20-1/4 i 2. APPLICABLE DOCUMENTS 2.1 The following documents of the issue in effect on date of invitation for bids or request for proposal, form a part of this specification to the

8、extent specified herein: SPECIFICATIONS FEDERAL QQ-A-200/3 QQ-A-225/6 QQ-A-250/8 QQ-S-7 66 TT-E-527 QQ-W-470 TT-P-17 57 MILITARY MIL-C-5541 Aluminum.Alloy Bar, Rod, Shapes, and Tube, Aluminum Alloy Bar, Rod, and Wire, Rolled, Aluminum Alloy, 5052, Plate and Sheet. Steel Plates, Sheets, and Strip Cor

9、rosion Enamel, Alkyd, Lustreless. Wire, Steel, High Carbon, Spring, Bright, Primer Coating, Zinc Chromate, Low Extruded, 2024. Drawn, or Cold Finished, 2024. Resisting. Music. Moisture Sensitivity. Chemical Films and Chemical Film Materials for Aluminum and Aluminum Alloys. 2 Licensed by Information

10、 Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-5 MIL-C-Lb775D b5 777770b 0257024 7 MIL-C-16775D STANDARDS FEDERAL FED-STD-151 Metals; Test Methods. FED-STD-595 Colors. MI LI TARY MIL-STD-105 Sampling Procedures and Tables for MIL-S

11、TD-129 Marking for Shipment and Storage. Inspection by Attributes. DRAWING Defense Medical Supply Center 20577 Chests, Medical Instrument and Supply Set, Field, Empty (5 sheets). (Copies of specifications, standards and drawing required by suppliers in connection with specific procurement functions

12、should be obtained from the procuring activity or as directed by the contracting officer.) 2.2 Other publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise indicated, the issue in effect on date of invitation for bids or request for p

13、roposal shall apply. AMERICAN SOCIETY FOR TESTING AND MATERIALS ASTM Standards and Tentative Standards Designation D 395 Standard Methods of Test Designation D 412 Tentative Method of Tension Designation D 1054 Standard Method of Test for for Compression Set of Vulcanized Rubber. Testing of Vulcaniz

14、ed Rubber. Impact Resilience and Penetration of Rubber by the Rebound Pendulum. 3 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-Lh775D 65 7997906 0259025 O W MIL-C-16775D (Application for copies should

15、 be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia 3, Pa.) 3 . REQUIREMENTS 3.1 Material. Except as specified herein, materials shall conform to the applicable portions of the specifications, standards, and drawing specified herein, and shall be capable o

16、f meeting tihe requirements specified therein. In addition, the metals shall conform to the chemical requirements of their applicable specifications when tested as specified in 4.4.4. When materials to be used are not specifically designated, those used shall be of the highest commercial quality, an

17、d entirely suitable for the purpose intended. 3 . 1.1 Aluminum. 3.1.1.1 The chest body, cover, separator pan, gasket retaining channel, drawbolt hanger plate, drawbolt lock, handle-plate, packboard hook plate, and corner reinforcement shall be constructed of 5052-TO aluminum alloy sheet conforming t

18、o QQ-A-250/8. 3.1.1.2 The handle shall be constructed of aluminum alloy conforming to grade AA-6063 of SAE AA-2024. The handle sleeve shall be constructed of 2024-T3 aluminum alloy conforming to QQ-A-200/3. of 2024-T4 aluminum alloy conforming to QQ-A-225/6. The strap and shouldered screw shall be c

19、onstructed 3.1.2 Corrosion-resistinq steel. 3.1.2.1 The drawbolt top hinge pin, separator pan washer, hexagon nuts and rivets shall be fabricated of corrosion- resisting steel conforming to class 302 or 304 of QQ-S-766. 3.1.2.2 The slot clip, and packboard hook shall be fabricated of corrosion-resis

20、ting steel conforming to class 430 of QQ-5-766. 3.1.3 Spring handle. Handle springs shall be constructed of steel wire conforming to QQ-W-470, except that the wire shall be uniformly coated with commercially pure zinc. The minimum weight of zinc coating shall be 0.30 ounces per square foot of surfac

21、e. 3.1.4 Rubber. Rubber for the gasket shall be a natural rubber, pure gum compound. The rubber shall be tested as specified in 4.4.2.2; the, physical properties shall conform to the following requirements: 4 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or ne

22、tworking permitted without license from IHS-,-,-F MIL-C-16775D 65 9 7797706 0257026 2 Minimum tensile strength - Minimum ultimate elongation - Maximum compression set - Maximum durometer reading - Maximum loss in tensile strength on accelerated aging - Maximum loss in ultimate elongation on accelera

23、ted aging - Maximum increase in durometer reading on accelerated aging - MIL-C-16775D 1,000 pounds per square 500 percent. 50 percent. 40 plus 5, minus 2. 20 percent. 30 percent. 10. inch (p.s.i). 3.1.5 Primer. The primer shall be zinc chromate conforming to color Y of TT-P-1757. 3.1.6 Enamel. The e

24、namel shall be synthetic lustreless olive drab, conforming to TT-E-527. The color shall be 34087 of FED- STD-595 (see 6.2). The enamel for identification marking (3.7) shall be black, color 37038 of FED-STD-595 (see 6.3), and shall also conform to TT-E-527. 3.1.7 Sealer. Sealer shall be 3M No. EC-80

25、0 or No. 2216, or Product Research 61 Chemical Corporation sealant, Part No. RR- 1422-B1/2 or a commercial sealer with the same specifications and tolerances, 3.1.8 Drawbolt fastener. Material for the drawbolt fastener shall be as specified on the drawing. O 3.2 Construction. The chest shall conform

26、 in al1 details to the requirements specified herein and as shown on the drawing, except that the embossed surfaces on the top of chests, elements 6 and 7, shall have a tolerance of 3/16 inch in concavity and convexity. The construction shall be sound, durable, and capable of meeting all tests herei

27、nafter specified. All hardware shall be flush-mounted, However, handles and draw-bolt fasteners shall project no further than 1/8 inch beyond the plane of the chest outer surface. 3.2.1 Detail. Each chest shall consist of an aluminum body with cover and separator pan where indicated, symmetrically m

28、ade, smoothly and properly finished. The chest body, cover, separator and channel retaining member for the rubber gasket shall be seamlessly die-drawn and trimmed as shown on the drawing. Slight flex warp to the cover element is acceptable. All other component shall have no flex, dimensional warp or

29、 structural deficiency. 5 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-16775D 3.2.2 Component parts. Each chest shall be composed of the respective chest elements as indicated in Table II, and constru

30、cted in accordance with the applicable portions of the drawing. TABLE II. Component parts listinq. I I I I Element No. I Pan I Body I required I I I I Size I Cover I I 1 I 2 2 I 4 3 I 4 4 I 6 5 I 6 6 I 7 I I 1 3 5 I 3 I I I 5 I 5 1 No I No I No I Yes I Yes I Yes I 3.2.3 Catch-draw. All parts shall b

31、e die-stamped and formed for uniform and interchangeable assembly. The slots in chest elements Nos. 2, 4, 6, and 7, respectively, wherein the drawbolt strike engages, shall be reinforced by a corrosion-resisting steel clip as shown on th drawing. 3.2.4 Gasket. The gasket shall be molded of the mater

32、ial specified in 3.1.4 and shall conform to the applicable portions of the drawing. (see 5.2). The gasket shall be suitably treated to prevent adhesive at the sealing edge. The finished gasket shall be capable of sealing and resealing the chest during functional testing of the completed chest, rende

33、ring it watertight in repeated use. with specification requirements, the gasket shall be fitted into its retaining member (see 4.4) . The molded gasket shall be placed into the chest When chests are tested to determine compliance 3.2.5 Drawbolt fasteners. The drawbolt fastener shall be fabricated in

34、 accordance with the drawing. 3.3 Weldinq. All welding shall be done with appropriate equipment properly regulated and operated by.thoroughly trained and experienced welders skilled in the operations of aluminum welding. Seam and fillet welds shall be continuous, even, and 6 Licensed by Information

35、Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c MIL-C-Lb775D 65 9999906 0259028 b MIL-C-16775D smooth. Spot welds shall be on not more than 2-inch centers, and e shall be accomplished so as to insure sound welds of sufficient stren

36、gth and completeness to tear the spot out of the parent metal when pulled apart. All exposed spot welds, seam and fillet weld shall be smooth and finished in accordance with best commercial practice. 3.4 Tolerances. Standard commercial tolerances shall be permissible on material gage sizes. Dimensio

37、nal tolerances shall be as specified on the drawing. Tolerances shall be held to a minimum for hinges, hinge-pins, bearings, channels, and all other fittings where accuracy is of paramount importance for proper operation and interchangeability of component parts. Sub and general assemblies shall be

38、precision-fitted for durable, smooth, and consistent functioning. End item interchangeability is most important due to varying end item uses. 3.4.1 Application of tolerances. The tolerances shown on the drawing shall be taken in such a manner that the followins requirments I. II. III. IV. V. - throu

39、gh V, inclusive, are conformed to: Chest elements shall be of such size that the appropriate “GO“ gage can be freely inserted (see 4.4.3). Rim of body shall be of sufficient height to prevent cover from contacting shoulder when properly secured to body. Chest cover shall be of such size as to freely

40、 overlay chest body and shall assemble thereto by the use of the drawbolt fastener attached to the chest body. The container as totally assembled, with gasket in place, shall be leakproof. Drawbolts and other hardware shall operate smoothly, shall not bind, and shall be capable of being easily opera

41、ted by hand without the use of tools. Chest bodies and chest covers shall be completely interchangeable and, when so interchanged, Ghall meet the requirements specified in subparagraph IV, above . 3.5 Finish. The entire unit, including outside and all accessible inside surfaces, shall be finished wi

42、th acid, alkali, and solvent-resisting enamel, as follows: 7 Licensed by Information Handling ServicesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NIL-C-16775D b5 m 999990b 0257029 m MIL-C-16775D 3.5.1 Deqreasing. All surfaces to be enameled shall

43、 be thoroughly cleaned and chemically degreased. 3.5.2 Primer. After degreasing, a primer coat shall be applied. The primer shall be zinc-chromate conforming to TL-P- 1757. The primer coat shall form a grounding bond and base for the finishing enamel. All surfaces, after degreasing, may be given a c

44、hemical treatment conforming to MIL-C-5541 in lieu of the zinc-chromate primer specified herein. 3.5.3 Enamel. The primer coat shall be followed by one coat of lustreless olive drab enamel conforming to TT-E-527. Each coat shall be sprayed on and baked in high-temperature oven in accordance with the

45、 paint manufacturers recommendations. The resultant finish shall be hard, smooth, and highly resistant to abrasion, chipping, and cracking. lustreless olive drab conforming to color 34087 of FED-STD-595 (see 6.2). 3.5.3.1 Color. The color of the final finish shall be 3.5.4 Touchup coat. If assembly

46、of body, cover, and component parts, after painting, as specified in 3.5.3, results in scratching and chipping of paint, the entire exterior of the body and cover shall receive a mist of lustreless olive drab enamel conforming to TT-E-527. After application of mist coat, chest shall be allowed to ai

47、r-dry in accordance with paint manufacturers recommendations. (see 3.1.7) shall be applied at the junction of the gasket retainer and the inner walls of chest element Nos. 6 and 7 as shown on the drawing. of the chest element through the openings in slots for the drawbolts when tested as specified i

48、n 4.4.2. 3.6 Sealinq. After finishing, a continuous fillet of sealer The sealer shall prevent water leaking out 3.7 Identification markinq. All components shall be permanently and legibly marked with black, lustreless enamel (see 3.1.6), in letters one-half inch high, with the name of the manufactur

49、er or registered trademark. Refer to Table III for marking instructions. 3.8 Preproduction samples of chests. Before production is bequn, the contractor shall submit to the procuring activity, for - approval two (2) preproduction samples. The chests shall be in strict accordance with applicable specification requirements. 8 Licensed by Information Handling ServicesProvided by IHSNot for