DLA MIL-C-40009E-1991 CABINETS STORAGE REPAIR PARTS AND TOOLS《保管柜 修理零件和工具》.pdf

1、MIL-C-40007E 71 = 7777906 047778b I INCH-POUND 1 MIL-C-40009E 29 March 1991 SUPERSEDING MIL-C-40009D 21 June 1968 MILITARY SPECIFICATION CABINETS, STORAGE, REPAIR PARTS AND TOOLS This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE AND CLASSIF

2、ICATION 1.1 Scope. This specification covers cabinets for the storage of repair parts and tools. 1.2 Classification. Cabinets covered by this specification shall be of the following types and classes, as specified (see 6.2): Type 1 - 35-112 inches high, 25 inches wide, 20 inches deep, (see figures 1

3、, 2 and 3). Class A - 12 drawers and 1 door enclosed bin. Class B - 24 drawers and 1 door enclosed bin. Class C - 18 drawers and 1 door enclosed bin. Type II - 35-112 inches high, 34 inches wide, 17-718 inches deep, 3 door enclosed shelves (see figure 4). Type III - 54-112 inches high, 36-112 inches

4、 wide, 23 inches deep, (see figures 5 and 6). Class A - 42 drawers and 4 sliding trays. Class B - 18 drawers and 7 open bins. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be used in improving this document should be addressed to: U.S. Army Natick Resea

5、rch, Development, and Engineering Center, Natick, MA 01760-5017 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 7125 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided b

6、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-40009E 71 II 9999906 0479787 MIL-C-40009E Type IV - 39 inches high, 46-314 inches wide, 23-9/16 inches deep, 14 drawers and lid enclosed top shelf (see figure 7). Type v - 35-112 inches high, 25 inches wide

7、, 27 inches deep, 11 drawers (see figure 8). Type VI - 24 inches high, 25 inches wide, 16-318 inches deep, 3 expanded metal shelves (see figure 9). 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.5. Specifications, standards, and handbooks. The following specifications, standards, and handbook

8、s form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited, in the solicitation (see 6.2). SPECIFICATI

9、ONS FEDERAL RR-C-271 - Chain and Attachments, Welded and Weldless TT-C-490 - Cleaning Methods for Ferrous Surfaces and TT-P-664 - Primer, Coating, Alkyd, Corrosion-Inhibiting, Pretreatments for Organic Coatings Lead and Chromate Free, VOC-Compliant MMM-A-125 - Adhesive, Casein-Type, Water- and Mold-

10、Resistant MMM-A-188 - Adhesive; Urea-Resin-Type (Liquid and Powder) MILITARY MIL-E-15090 - Enamel, Equipment, Light-Gray (Formula No. 111) MIL-M-17194 - Metal, Expanded, Steel MIL-B-45977 - Bins, Cabinets, Shelving, and Worktables, Packaging Of 2 Provided by IHSNot for ResaleNo reproduction or netwo

11、rking permitted without license from IHS-,-,-MIL-C-40009E STANDARDS FEDERAL FED-STD-595 - Colors, Used in Government Procurement FED-STD-H28 - Screw-Thread Standards for Federal Services MILITARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-130 - Identification Marking of U

12、.S. Military Property Attributes (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.12 Other Government documents, drawings,

13、 and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. are those cited in the solicitation. Unless otherwise specified, the issues DRAWINGS U.S. ARMY NATICK RESEARCH, DEVELOPMENT, AND ENGINEERING CENTER 5 -

14、1 3 -22 95 5-13 -2296 5 -13 -2297 5-13-2298 5-13-2299 5-1 3 -2300 5-13-2301 5 -1 3 -2302 5 -1 3 -2 3 03 5-1 3 -2304 5 -1 3 -230 5 5-1 3 -2306 5 -1 3 -2307 5 -1 3 -230 8 5 -1 3 -2309 Cabinets, Storage, Repair Parts and Tools: Type I, Type I, Class B and C, Drawer Assembly, Size “a“ Type I, Class A an

15、d C, Drawer Assembly, Size “b“ Type I, Class B and C, Drawer Assembly, Size “c“ Type I, Class A and C, Drawer Assembly, Size “d“ Cabinets, Storage, Repair Parts and Tools: Type II, Cabinet Assembly Cabinets, Storage, Repair Parts and Tools: Type III, Cabinets Assembly, Class A and B Type III, Class

16、A, Sliding Tray Assembly Type III, Class A and B, Drawer Assembly, Size “e“ Cabinets, Storage, Repair Parts and Tools: Type IV, Type IV, Drawer Compartment Assembly Type IV, Drawer Assembly, Size “f“ Type IV, Drawer Assembly, Size g“ Type IV, Drawer Assembly, Size “h“ Cabinets, Storage, Repair Parts

17、 and Tools: Type V, Cabinet Assembly, Class A, B and C Cabinet Assembly Cabinet Assembly 3 MIL-C-40007E 7% m 7777906 0477788 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-40009E 5-13-2310 - Type V, Drawer Assembly, Size “j“ 5-13-2311 - Type

18、 V, Drawer Assembly, Size “k“ 5-13-2312 - Cabinets, Storage, Repair Parts and Tools: Type VI, Cabinet Assembly, Expanded Metal (Copies of drawings are available from the U.S. Army Natick Research, Development, and Engineering Center, ATTN: STRNC-UX, Natick, MA 01760-5017.) 2.2 Non-Government publica

19、tions. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted are those listed in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not lis

20、ted in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) A135.4 - Basic Hardboard A208.1 - Mat-Formed Wood Particleboard (Copies may be obtained from the American National Standards Institute, 1430 Broadway, New York, NY 1001

21、8.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) A 366 - Steel, Sheet, Carbon, Cold-Rolled, Commercial Quality A 510 - General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel A 569 - Steel, Carbon (0.15 Maximum, Percent) Hot-Rolled Sheet and Strip, Commercial Quality A 853 - Stee

22、l Wire, Carbon, for General Use D 2016 - Moisture Content of Wood (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103-1187.) (Non-Government standards and other publications are normally available from organizations

23、that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence.

24、 Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-40009E 71 9999906 0479790 T -1 MIL-C-40009E 3, REQUIREMENTS 3.1 Firs

25、t article. When specified (see 6.21, a sample shall be subjected to first article inspection (see 6.31, in accordance with 4.3. 3.2 Materials. Materials shall conform to the applicable specifications, standards, and requirements specified herein and on the applicable drawings. Materials not specific

26、ally defined shall be as regularly used by the manufacturer. long as it meets the requirements of this specification. It is encouraged that recycled material be used when practical as 3.2.1 Steel. 3.2.1.1 Steel, sheet and strip. Sheet and strip steel components shall be fabricated from hot rolled or

27、 cold rolled steel conforming to ASTM A 569 and ASTM A 366. 3.2.1.2 Wire, steel. Steel wire components shall be fabricated from No.s 1010, 1015 or 1020 of ASTM A 510, bare finish, annealed steel wire conforming to ASTM A 853. 3.2.1.3 Metal, expanded, steel. Panels for expanded metal components shall

28、 conform to type II, class 2, grade A of MIL-M-17194. 32.2 Wood. Wood for the core of composite wood tops shall be low density hardwood or softwood, having a minimum rated weight of 50 pounds per cubic foot conforming to ANSI A208.1. The moisture content of wood shall be determined in accordance wit

29、h ASTM D 2016 at a 10 percent moisture content. 3.2.3 Hardboard. Hardboard for cabinet top veneers shall be a minimum 1/8 inch thick, class 1 tempered, conforming to ANSI A135.4. The hardboard of types I and V cabinets shall be smooth on two sides. For type IV cabinets, the hardboard shall be smooth

30、 on one side. 3.2.4 Particleboard. Particleboard for cabinet tops shall conform to ANSI A208.1, with the following indicated requirements and applications. a. Particleboard core - type 1, grade 1-M-2. b. Particleboard face and back veneers - type 1, grade 1-M-2, 3/8 inch thick, sanded two sides. 3.2

31、.5 Adhesives. Adhesives for bonding cabinet tops shall conform to the following: 3.2.5.1 Adhesive, casein-type. Casein-type adhesive shall conform to type II of MMM-A-125. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-40009E 73 9 9999906 04

32、79793 3 W MIL-C-40009E 3.2.5.2 Adhesive, urea-resin-type. Urea-resin-type adhesive shall confarm to type III of MMM-A-188. 3.2.5.3 Adhesive, thermosetting vinyl-emulsion type. Thermosetting vinyl- emulsion type adhesive shall meet the block shear strength, tension loading shear strength, both wet an

33、d dry, and pH requirements of MMM-A-188. 3.2.6 Primer. Primer shall conform to composition L of TT-P-664. 3.2.7 Enamel. Enamel shall conform to type III, class 2 of MIL-E-15090, except that the color shall be Olive Drab color No. 24087 of FED-STD-595. 3.2.8 Chain. Chains shall be type II, class 6, w

34、eldless, steel, zinc-coated safety chain conforming to -C-271. 3.3 Design and construction. The cabinets shall conform to the requirements Details not specified herein and on the applicable drawings referenced in 2.1. specifically defined shall be in accordance with the manufacturers regular practic

35、e. Figures 1 through 9 are included herewith for ready identification of the various types and classes of cabinets, and to illustrate the major distinguishing features and overall dimensions applicable to each. I 3.3.1 Welding. Welding, where specified or used as an option, may be used only in fabri

36、cation of the original item and shall not be used as a repair measure. All welds shall be accomplished in accordance with commercial practice, and shall be smooth, sound, and free from porosity, burned or reduced areas, fractures, and undercut. Welding scale shall be removed, and rough edges and pro

37、jections shall be dressed smooth. 3.3.2 Fastening devices. Fastening devices shall be standard commercial items, fabricated from steel, and shall have a zinc or cadmium plated finish. Threaded fasteners shall be installed with lockwashers or self-locking nuts to prevent loss of tightness. Fastening

38、devices subject to removal or adjustment shall not be peened, swaged, staked, or otherwise deformed to prevent adjustment or removal. All threaded parts shall be in the inch system and shall comply with FED-STD-H28. 3.3.3 Sheet metal components. All like bends of sheet metal components shall be of u

39、niform radius, and unless otherwise specified on the drawings, radii shall be as small as practicable in relation to sheet metal thickness, All exposed sheet metal edges shall be free of sharp edges and burrs. 3.3.4 Riveting. When applicable, holes for rivets shall be of a diameter to insure a snug

40、fit with the rivet shank after setting. holes shall be drilled or punched at time of assembly. Burrs at rivet holes that may prevent proper seating of rivet heads shall be removed. Setting of When practicable rivet 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

41、e from IHS-,-,-MIL-C-40009E 71 399990b 0479792 3 i -. MIL-C-40009E rivets shall be accomplished so that mating surfaces are drawn tight. heads shall be in full contact with mating surfaces, concentric with the rivet shank, and rivet heads shall be free from splits, burrs, and sharp edges. The rivet

42、3.3.5 Base and cabinet sides assembly. The cabinet base shall be assembled to the cabinet sides so that the assembled cabinet is not supported by any sheet metal edges. 3.3.6 Cabinet drawers. The cabinet drawers shall be equipped with stops wherever shown on applicable drawings. The drawer stops sha

43、ll prevent drawer removal when opened in a normal manner, but shall permit drawers to be intentionally removed. Two drawer guides shall be furnished for each drawer in all cabinets. The sides of the cabinets may be used as guides for drawers adjacent to the sides. When the applicable drawings do not

44、 specifically define the configuration of the guides, the configuration shall be in accordance with the manufacturers standard practice. All drawers of one size shall be interchangeable, The drawers shall operate smoothly without binding and shall not have more than 1/4 inch total side clearance bet

45、ween the drawers and drawer guides. The front face of drawers shall be flush with face of shelves within 1/16 inch. drawings, or alternatively, the ribs and slots shall be the manufacturers current method of fabrication, providing that equal compartmenting and rigidity capabilities as shown on the d

46、rawings are maintained. Fabrication of drawer ribs and slots shall be as shown on applicable 3.3.7 Doors. 3.3.7.1 Bin doors. Bin doors shall be removable from the cabinets by sliding the open door to the right. each bin door on types I and II cabinets shall be equipped with two restraining chains sp

47、ecified in 3.2.8, located as shown on the applicable drawings. Restraining chains shall not be required for the bottom door of type II cabinets. horizontal plane. The chains shall be attached by bolting, welding, or riveting. edge of the shelf, and shall not recess more than 1/8 inch from the front

48、edge of the shelf. Except for the bottom door of type II cabinets, The chains shall be of sufficient length to retain the open door in a The closed doors shall not extend more than 1/8 inch beyond the front 3.3.7.1.1 Bin door latches. The latching assembly for bin doors shall be fabricated of not le

49、ss than 1/8 inch thick steel. The fixed portion shall be attached by welding or riveting. The pivoting handle shall be secured to the door by riveting. The attached latch shall have a positive engagement. 3.3.7.2 Fu11 height doors. Full height double doors shall have the right- hand door equipped with a three point latching device, and the left-hand door equipped with a two point latching device. The latching mechanism shall be controlled by handles of