DLA MIL-DTL-17376 2 B-2012 CAPS AND FLANGES COMPRESSED-GAS CYLINDER FLANGES LOW PRESSURE.pdf

1、 AMSC N/A FSC 8120 INCH-POUND MIL-DTL-17376/2B 8 MAY 2012 SUPERSEDING MIL-C-17376/2A 22 MARCH 2007 DETAIL SPECIFICATION SHEET CAPS AND FLANGES COMPRESSED-GAS CYLINDER: FLANGES, LOW PRESSURE Reactivated after 22 March 2007 and may be used for new and existing designs and acquisitions. This detail spe

2、cification sheet is approved for use by all departments and agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this detail specification sheet and MIL-DTL-17376. INTENDED USE: 1. The flanges covered by this specification sheet are inte

3、nded to provide anchorage for a cylinder protective cap to the shoulder of a cylinder. The flanges are attached to the cylinder by welding of similar metals and are for low pressure application. The flange provides inlet valve threads for cylinder valves and when required, threaded holes for cylinde

4、r safety devices for acetylene. REQUIREMENTS: 1. Flange: The compressed-gas cylinder low pressure flange shall be as specified herein and in accordance with figures 1 and 2. Figures 1 and 2 are a representative configuration and method of attaching flanges to cylinders and may be varied provided dim

5、ensions of threaded portions are as shown. 2. Material: The steel used shall have a carbon content not greater than 0.25 percent, or shall be composition G41000 of SAE J402, “(R) New Steel Designation System for Wrought or Rolled Steel”. Provided by IHSNot for ResaleNo reproduction or networking per

6、mitted without license from IHS-,-,-MIL-DTL-17376/2B 2 NOTES: 1. Part or identification number (PIN) to be used for low pressure flanges acquired to this detail specification are created as follows: MIN.7/16TAP TO RECEIVE VALVE REQUIREDNGT THREADSASize Part number Dimension A 1 C17376/2-1 3-1/8-11 U

7、NS-1 2 C17376/2-2 3-1/2-11 UNS-1 NOTE: 1. All dimensions are in inches. FIGURE 1. Flange. M 17376/2 X Size: 1 = C17376/2-1 (3-1/8-11 UNS-1) flange 2 = C17376/2-2 (3-1/2-11 UNS-1) flange 3 = C17376/2-3 (3-1/8-11 UNS-1) flange with safety 4 = C17376/2-4 (3-1/2-11 UNS-1) flange with safety Specificatio

8、n sheet number M prefix General specification number Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-17376/2B 3 7/16MIN.TAP TO RECEIVEVALVE REQUIREDNGT THREADSHOLES TAPPEDFOR STDSAFTEY PLUGSNGT THREADSASize Part number Dimension A 3 C17376/2-

9、3 3-1/8-11 UNS-1 4 C17376/2-4 3-1/2-11 UNS-1 NOTE: 1. All dimensions are in inches. FIGURE 2. Flange with safety. Custodians: Preparing Activity: Army - CR4 Navy - YD Air Force 68 DLA-GS DLA - GS7 (Project 8120-2012-001) Review Activities: Army - MD Navy - MC NOTE: The activities listed above were i

10、nterested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-