DLA MIL-DTL-32063-2000 TARPAULINS COTTON OR POLYESTER FWWMR [Superseded DLA K-P-146 E CANC NOTICE 1 DLA K-P-146 E CANC NOTICE 1 DLA K-P-146 E INT AMD 1 DLA K-P-146 E DLA K-P-146 D .pdf

1、9799906 2112355 726 I INCH-POUND I MIL-DTL-32063 15 March, 2000 SUPERSEDING 13 February 1979 . K-P-146E DETAILED SPECIFICATION TARPAULINS, COTTON OR POLYESTER, FWWMR This specification is approved for use by ali Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specific

2、ation covers uncoated cotton duck tarpaulins (see 6. I). 1.2 Classification. 1.2.1 Tpes. (see 6.2). Type I - With loops Type II - With grommets and tie ropes 1.2.2 Classes and sizes. (see 6.3). Beneficial comments (recommendations, additions, deletions, clarifications) and any pertinent data which m

3、ay be of use in improving this document should be addressed to: Defense Supply Center Philadelphia, Clothing and Textiles Directorate, Attn: DSCP-PNR, 700 Robbins Ave., Philadelphia, PA 191 11-5096 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this

4、 document or by letter. AMSC NIA FSC 8340 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32063 Class 1 - Cloth, duck, cotton, No. 6 hard texture, Camouflage Green 483. 5 feet by 5 feet 10 feet by 6 feet 12 feet by 10 feet 17 feet by 12 feet

5、20 feet by 20 feet 23 feet by 15 feet 26 feet by 22 feet 40 feet by 20 feet Class 2 - Cloth, duck, cotton, No. 6 hard texture, deck gray Navy shade 3 104. 8 feet by 8 feet 15 feet by 15 feet 20 feet by 20 feet Class 3 - Cloth, duck, cotton, No. 10 hard texture, unbleached. 7 feet by 15 feet 7 feet b

6、y 16 feet 7 feet by 18 feet 16 feet by 16 feet Class 4 - Cloth, duck, cotton, No. 6 hard texture, Desert Tan 459. 5 feet by 5 feet 10 feet by 6 feet 12 feet by 10 feet 17 feet by 12 feet 20 feet by 20 feet 23 feet by 15 feet 26 feet by 22 feet 40 feet by 20 feet 2. APPLICABLE DOCUMENTS 2.1 General.

7、The documents listed in this section are specified in sections 3 and 4 of this specifxation. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of

8、this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. c I 2.2 Government docunients. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

9、 IHS-,-,-iai 9Ob 2LL2357 5T m MIL-DTL-32 O 63 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of

10、 the Department of Defense Index of Specdcations and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL A-A- 145 1 V-T-285 T-R-605 T-T-6 16 TT-P- 5 95 ccc-c-419 CCC-C-428 DDD-L-20 - Twine, Fibrous - Thread, Polyester - Rope, Manila and Sisal - Trea

11、tment: Mildew Resistant, for Rope and Cord - Preservative Coating, Canvas - Cloth, Duck, Cotton, Unbleached, Plied -Yarns, Army and Numbered - Cloth, Duck, Cotton, Fire, Water, Weather and Mildew Resistant - Label: For Clothing, Equipage and Tentage (General Use) MILITARY MIL-W-530 MIL-G-16491 - Gro

12、mmet, Metallic MIL-PRF-20696 - Webbing, Textile, Cotton, General Purpose - Cloth, Waterproof, Weather Resistant STANDARDS FEDERAL FED-STD-595 - Colors Used in Government Procurements (Unless otherwise indicated. copies of federal and military specifications, standards, and handbooks are available fr

13、om the Document Automation and Production Service, Bldg. 4D (DPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA 19 1 1 1-5094.) 2.2.2 Other Government documents, drawings. and publications. The following other Government documents, drawings, and publications form a part of this document to the extent

14、 specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS U.S. ARMY SOLDIER BIOLOGICAL CHEMICAL COMMAND 5-10-9 - Tarpaulins: Duck, Cotton: FWWMR (Copies of drawings are available from the U. S. Army Biological Chemical Command, ATTN: AMSSB-REO-S(N), NATI

15、CK, MA 01760-5017.) Department of the Army Field Manual FM 1 O- 16 - General Repair of Tents, Canvas and (Applications for copies should be addressed to the Superintendent of Documents, US Webbing Government Printing Office, Washington, DC 20402) 3 Provided by IHSNot for ResaleNo reproduction or net

16、working permitted without license from IHS-,-,-Ob 2112358 435 MIL-DTL-32063 2.3 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are those listed in the is

17、sue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM-D-6 193 - Standard Practice for Stitches and Seams (Ap

18、plications for copies of referenced documents should be addressed to the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19426- 2959.) 2.4 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein,

19、the text of this specification takes precedence. Nothing in this specification, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When Specified (see 6.2), a sample shall be subjected to first article 3.2 Materials a

20、nd components. inspection (see 4.2 and 6.2). 3.2.1 Cloth. 3.2.1.1 Cloth, Duck, Cotton Camouflage Green 483. Cloth for the. class 1 tarpaulins shall be type I, No, 6, hard texture duck of CCC-(2-419, finished to conform to type I, class 1 of CCC-C-428. As an alternate, the cloth for class 1 tarpaulin

21、s shall be type 2,4 or 5, Class 2 or 3 of MIL-PW-20696. The color of the cloth shall be camouflage green 483 conforming to color chip 34094 of FED-STD-595. 3.2.1.2 Cloth. Duck, Cottdn Deck Gray Navy shade 3 104. Cloth for the class 2 tarpaulins shall be type I, No. 6, hard texture duck of CCC-C-419,

22、 finished to conform to type I, class 1 of CCC-C-428. As an alternate, the cloth for class 2 tarpaulins shall be type 2,3 or 5, Class 2 or 3 of MIL-PRF-20696. The color of the cloth shad be deck gray navy shade 3 104. 3.2.1.3 Cloth. Duck, Cotton unbleached. Cloth for the class 3 tarpaulins shall be

23、type I, No. 10, hard texture duck of CCC-C-419, except for weight which shall be 12.5 oz/yd2 minimum and 14.35 odyd2 maximum. Air permeability requirements shall not be applicable. The unbleached cloth shall be finished to conform to class 1 of CCC-C-428, except that the flexibility requirements sha

24、ll not apply. 3.2.1.4 Cloth, Duck, Cotton. Cloth for the class 4 tarpaulins shall be type I, No. 6, hard texture duck of CCC-C-419, finshed to conform to type I, class 1 of CCC-C-428. As an 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-32

25、063 alternate, the cloth for class 4 tarpaulins shall be type 2,4 or 5, Class 2 or 3 of MIL-PRF-20696. The color of the cloth shall be Desert Tan 459. 3.2.2. Webbing, cotton. Webbing shall conform to type III, class 4, 1 inch width of MIL- W-530. The color shall be camouflage green 483 conforming to

26、 color chip 34094 of FED-STD- 595 for class 1 tarpaulins, deck gray Navy shade 3 104 for class 2 tarpaulins and dyed shade 459 Desert Tan for class 4 tarpaulins. When type I, class 3 tarpaulins are required, webbing shall conform to type III, class 1 of MIL-W-530. 3.2.3 Thread, polyester. Thread sha

27、ll conform to type I, class 1, subclass B of V-T-285. Thread size shall be as follows: a. For all stitching except zig-zag stitching and stitching indicated by “2” on drawings size FF for needle and bobbin. b. For zig-zag stitching, size F for needle and bobbin. c. For stitching indicated by “Z” on

28、drawing size FF for needle and size F for looper. 3.2.3.1 Color and treatment. Thread for the class 2 and 3 tarpaulins shall be natural color. The color of the thread for the class 1 tarpaulins shall be camouflage green 483 conforming to color chip 34094 of FED-STD-595. Thread for the class 4 tarpau

29、lins shall be dyed Desert Tan 459. The dyed thread shall show colorfastness to weathering equal to or better than the standard sample (see 6.3). When no standard shade sample is available, the dyed thread shall show good colorfastness to weathering. 3.2.4 Twine, cotton. Twine shall be 5-ply of A-A-1

30、45 1. 3.2.5 Rope, manila., Rope shall conform to type M, class 2 of T-R-605, 1/1/8 inch circumference, mildew resistant treated in accordance with T-T-616. 3.2.6 Grommet, metallic. Grommets shail conform to type III, class 3, size Nos. O, 1, 3,4 and 5 of MIL-G-16491. 3.3 Construction. Construction s

31、hall conform to drawing 5-10-9 and as specified herein. 3.3.1 Stitching, machine. 3.3.1.1 Types. AU stitch types, except bartacking, shall conform to ASTM-D-6 193 as fo Il0 ws : a. For all stitching except zig-zag stitching and stitching indicated by “Z” on b. For zig-zag stitching - type 304, 12 to

32、 16 stitches per inch. drawings - type 301,5 to 7 stitches per inch. c. For stitching indicated by “Z” on drawings fasteners - type 401, 5 to 7 stitches per inch. * 3.3.1.2 Thread breaks. Thread breaks in stitching shall be overstitched not less than 1 inch at each break on stitch type 301, not less

33、 than % inch at each break on stitch type 304 and not less 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-9999906 21123b0 093 MIL-DTL-32063 than 1 $4 inches at each break on stitch type 401. Thread breaks in type 401 stitching may be overstitched

34、with stitch type 301. 3.3.1.3 Stitching ends. The ends of 301 stitching shall be overstitched not less than 1 inch except where ends are turned under in a hem or held down by other stitching. Where 301 stitching is performed automaticdy.on stitch patterns such as box, box with cross-stitch, “W stitc

35、hing or straight line tacking, not less than three tying, overlapping , or back stitches shall be used to secure the ends of stitching. The ends of type 304 stitching shall be firmly secured by backstitching or overstitching or by increasing the number of stitches per inch at the ends for a minimum

36、of Yi inch. 3.3.1.4 Skitmed stitches. Two or more consecutively skipped stitches occurring in type 301 or 304 stitching shall be overstitched not less than 1 inch. Any skipped stitches in type 401 stitching shall be overstitched not less than 1 % inches. Skipped stitches in 401 stitching may be over

37、stitched with type 301 stitching. prior to or during the sewing operation is prohibited. 3.3.1.5 Thread lubricant. The addition of any lubricant to the polyester sewing thread 3.3.1.6 Stitchinn margins. All stitching margins shall be 1/8 _+ 1/16 inch. 3.3.2 Setting of grommets, (tvue II tarpaulins).

38、 Holes punched to receive grommets shall be smaller than the outside diameter of the grommet barrel so that the barrel must be forced through the hole. Grommets shall be securely clinched without cutting the materials. Roll of the clinched grommet shall not contah more than three scores (splits). 3.

39、3.3 Tie roDes, (me II tarpaulins). The tie ropes shall be constructed of the material specified in 3.2.5. Eye splices shall have three tucks and the ends of all strands shall be clipped to a length of not less than 1 inch nor more than 1 Yi inches. The size of the eye shall be as specified on the dr

40、awing and shall be the measurement of the inside of the loop when stretched taut. 3.3.4 Wicking of sewing thread (CUP test). There shall be no dripping of water through the panel lap seam stitching when the tarpaulin is tested as specified in 4.4.5. Seepage or leakage of water at a few points caused

41、 by hydrostatic pressure through needle holes or between plies of a lap seam shali not be scored as a failure. The seam leakage test is intended to insure that nonwicking thread has been utilized and that no lubrication has been added to the polyester thread prior to or during the sewing operation.

42、3.3.5 ReDaks. All necessary repairs shall be effected in accordance with Department of the Army Field Manual FM 10-16, except that hand-sewn patches or cemented patches will ncit be acceptable. Repairs required as a result of failure of the cup test and when authorized by the contracting officer sha

43、ll be performed with a suitable adhesive (see 6.5). 3.4 Marking. All markings and labels shall conform to Type IV, class 8 of DDD-L-20. 3.4.1 SDecial marking. The letters “US” shal conform to type IV, class 9 in the size characters and locations shown on the drawings. Class 9 markings shall be clear

44、ly legible after subjection to accelerated weathering. 3.4.2 Workmanship. Cloth components shall be clean and fiee of holes, cuts, tears, or cloth defects such as multiple floats, broken or missing yarns, or areas untreated with compound. Webbing shall not have fiayed or scalloped edges and rope com

45、ponents shali be iee of cuts or breaks. Thread tension shd be maintained so that there will be no loose stitching, and seam allowances shall be maintained with seams properly sewn so that no run-offs, twists, pleats or 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without li

46、cense from IHS-,-,-9999906 2112361 T2T W MIL-DTL-32063 open seams shall result. Care shac be taken in sewing to see that no needle chews occur. AU thread ends shall be trimmed to % inch or less. Metal components shall be fiee of burrs, sharp edges and corroded areas and shall not be broken or maKorm

47、ed. 3.5 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance requirements, and promotes economically advanta

48、geous life cycle costs. 4. VERIFICATION 4.1 Classification of inspections. The inspection requirements specified herein are classified as follows: a. b. Conformance inspection (see 4.3). First article inspection (see 4.2). 4.2 First article inspection When a first article is required (see 6.2) it sh

49、all be examined for the defects listed in 4.4.3 and tested as specified in 4.5.1. The presence of any defect or failure of any test shall be cause for rejection of the first article. 4.3 Conformance inspection. Sampling for inspection shall be as specified in the contract or purchase order. 4.4.1 Component and material inspection. In accordance with 4.1, components and materials shall be inspected in accordance with all the requirements of referenced docum