DLA MIL-DTL-5423 13 D-2009 BOOT DUST AND WATER SEAL TYPE D (FOR LEVER OPERATED CIRCUIT BREAKERS) STYLE 1 (PANEL MOUNTED WITHOUT MOUNTING FRAME).pdf

1、INCH-POUND MIL-DTL-5423/13D 17 February 2009 SUPERSEDING MIL-DTL-5423/13C 4 February 2008 DETAIL SPECIFICATION SHEET BOOT, DUST AND WATER SEAL, TYPE D (FOR LEVER OPERATED CIRCUIT BREAKERS), STYLE 1 (PANEL MOUNTED WITHOUT MOUNTING FRAME) This specification sheet is approved for use by all Departments

2、 and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-5423. FIGURE 1. Dimensions and configuration boots type D, style 1. AMSC N/A FSC 5930 Provided by IHSNot for ResaleNo reproduction or networki

3、ng permitted without license from IHS-,-,-MIL-DTL-5423/13D 2 (For number of screws and location see table II.) “0“- RING-SILICONEInches mm 0.016 0.5 0.906 1.000 1.812 2.500 .41 1.27 23.01 25.40 46.02 63.50 NOTES: 1. Dimensions are in inches. 2. Metric equivalents are given for general information on

4、ly. 3. Unless otherwise specified, tolerances are .02 (.51mm) for two place decimals and .031 (.79 mm) for three place decimals. 4. The number of mounting screws shall be supplied as indicated. 5. Edges shall be smooth and free from burrs. FIGURE 1. Dimensions and configuration boots type D, style 1

5、 - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-5423/13D 3 REQUIREMENTS Dimensions and configuration: See figure 1. Silicon rubber: Grade 50, class III, transparent. Splashproof: In accordance with MIL-STD-108, table I. Enduranc

6、e: 10,000 operations. Minute cracks after life test, which do not permit leakage, shall not be cause for rejection. Part or Identifying Number (PIN): See tables I and II. Table I. Dimensions. Dimensions .031 (.79) PIN M5423/13- L1 W1 W2 L2 01 1.250 (31.75) .750 (19.05) .531 (13.49) .60 (15.24) 02 1.

7、312 (33.32) 1.500 (38.10) 1.250 (31.75) .60 (15.24) 03 1.281 (32.54) 2.250 (57.15) 2.000 (50.80) .60 (15.24) Table II. Mounting holes, markings, and panel cutout. Mounting holes Location Panel cutout PIN M5423/13- Number of screws B B1 Markings X Y 01 2 Yes None None 1.250 (31.75) .531 (13.49) 02 4

8、None .375 (9.53) On-off 1.312 (33.32) 1.250 (31.75) 03 6 Yes .750 (19.05) None 1.281 (32.54) 2.000 (50.80) Qualification: First Article Testing in accordance with MIL-DTL-5423. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-5423/13D 4 The ma

9、rgins of this specification are marked with vertical lines to indicate where modifications were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of

10、this document based on the entire content irrespective of the marginal notations. Referenced documents: MIL-DTL-5423 MIL-STD-108 ASTM-A493 Custodians: Preparing activity: Army - CR DLA - CC Navy - AS Air Force - 85 (Project 5930-2008-069) DLA - CC Review activities: Army - AT, AV, CR4, MI Navy - CG,

11、 EC, MC Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-