DLA MIL-DTL-83528 10 D-2013 GASKETING MATERIAL CONDUCTIVE ELASTOMER ELECTRICAL EMI RFI CHANNEL STRIP.pdf

1、 MIL-DTL-83528/10D 12 August 2013 SUPERSEDING MIL-DTL-83528/10C 15 November 2001 DETAIL SPECIFICATION SHEET GASKETING MATERIAL, CONDUCTIVE, ELASTOMER, ELECTRICAL, EMI/RFI, CHANNEL STRIP This specification is approved for use by all Departments and Agencies of the Department of Defense. The requireme

2、nts for acquiring the relay described herein shall consist of this specification sheet and the latest issue of MIL-DTL-83528. NOTES: 1. Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. 2. Length shall be as specified on the purchase order. F

3、IGURE 1. EMI/RFI gasket, elastomer, and channel strip. AMSC N/A FSC 5999 INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/10D 2 REQUIREMENTS: Design and interface: See figure 1 and table I. Material: Type A, B, C, D, E, F, J,

4、K, L, or M. Part or Identifying Number (PIN): See table I. Supersession information: See table II. TABLE I. Dimensions. PIN 1/ M83528/010X Nominal dimensions 2/ 3/ Cross section area (cm2) 4/ A B C D 001 0.100 (2.54) 0.100 (2.54) 0.034 (0.86) 0.033 (0.84) 0.050 002 0.126 (3.20) 0.110 (2.79) 0.025 (0

5、.64) 0.050 (1.27) 0.079 003 0.126 (3.20) 0.225 (5.72) 0.020 (0.51) 0.075 (1.91) 0.164 004 0.156 (3.96) 0.156 (3.96) 0.062 (1.57) 0.047 (1.19) 0.113 005 0.175 (4.45) 0.156 (3.96) 0.047 (1.19) 0.075 (1.91) 0.152 006 0.327 (8.31) 0.235 (5.97) 0.062 (1.57) 0.115 (2.92) 0.448 1/ “X” in the PIN shall be r

6、eplaced by the applicable material type. Complete PIN example: M38528/0010A001. 2/ Dimensions are in inches; metric equivalents are given in parenthesis and are for general information only. 3/ Tolerance shall be as follows: Dimensions Tolerance Under .101 (2.57) .101 to .200 (2.57 to 5.08) .201 to

7、.300 (5.10 to 7.62) .301 to .500 (7.62 to 12.70) .005 (0.13) .008 (0.20) .010 (0.25) .015 (0.38) 4/ For calculation of volume resistivity (for reference only). TABLE II. Supersession information. PIN 1/ M83528/010X Superseded DESC Drawing PIN 85109X 1/ 001 001002 002003 003 004 004005 005006 006 1/

8、“X” in the PIN indicates the applicable material type. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for

9、 any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. This document references MIL-DTL-83528. Prov

10、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83528/10D 3 Custodians: Preparing activity: Army CR DLA CC Navy EC Air Force 85 (Project 5999-2013-006) DLA CC Review activities: Air Force 19, 99 NSA NS NOTE: The activities listed above were inter

11、ested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-