DLA MIL-P-0036599-1969 PIPETS PLASTIC DISPOSABLE STERILE《一次性无菌塑料吸移管》.pdf

1、 . KIL “MY SPECIT ICATION A PIPETS, PLASTIC, DISPOSABLE, STERILE This limited coordirxtion Hilitary Specification has been prepared by the DeEenst Personnel Support Center based upon currently available technics1 information, but it has not been apnroved for promulgation as a coordhated document. It

2、 is subject to modification. gation as a coordinated Hilitary Speciiication, it my be used in procurement. Xowever, pending its promul- I. SCOPE. 1.1 Scope, l%is specification covers three types of sterile, dis- posable, plastic, cotton plugged pipets suitable for use in laboratory procedures. 1.2 C

3、lassiTication. .1.2.1 lyp es, ciasses aii styles. Sterile, disposable pipets covered by this specizication sira 3e of the following types nd classes, as specified (sec 6.3) : 2. Type I .;cerai Type II SeJiogicai Type III sacter Lological Class 1. 1.0 aiiiiliter (mi), Wot Graduated Class 2. ;.G d in

4、1/15 rrl Class -.cJ ni L? 1/ior/ ml Class 4. i.1 ml in i., G.5 al Class S. 5.C mi ir? 1/iC ml Ciass G. G.J 1 ii-i /d nil APF ICY322 2: /- !i Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-0036579 66 W 7779906 0336950 L MU-P-0036 593 (DSA-DX; S

5、PECIFICATIOHS Federal MMK-A-250 Adhesive, Water-Resistant (for sealing fiberboard PPP-B-566 Boxes, Folding, Paperboard. PPP-B-58 5 Boxes, Wood, Wirebound. PPP-B-601 . Boxes, Wood, Cleated-Plywood. PPP-B-6 21 Boxes, Wood, Nailed and Lock-Corner. PPP-B-6 36 Box , Fiberboard. PPP-B - 67 6 Boxes, Set-Up

6、,-Paperboard. PPP- T-7 6 Tape, Pressure-Sensitive Adhesive Paper. (for carton sealing) . boxes). Mil i tary MIL-L-10547 Liners, Case, and Sheet, Overwrap; Water- Vaporproof or Waterproof Flexible, STANDARDS Military PIIL-STD-105 Sampling Procedures and Tables for Inspection MIL-STD-129 Attributes. M

7、arking for Shipment and Storage. Y (Copies of specifications and standards required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contraction officer.) 3. REQUIREMENTS 3.1 Materials. 3.1.1 Plastic. The material use

8、d b the pipets chail be transparent, general purpose, extrusion grade, virgin polystyrene suitable for the purpose intended. 3.1.1.1 Toxicity. The product material (finished pipet) shall contain no toxic substances which may affect the viability of micro-organisms that may come in contact with the p

9、ipet during normal use. specified in 4.4.4, growth in the test culture shall not be less than 90 percent of that of the control. G%en tested as - 2- . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-003b577 66 W 777770b 0336753 3 W _ - L- MIL-P

10、-0036599 (DSA-DM) 3.1.2 Cotton. “he cotton used for plugging the ends of the pipets shall be non-absorbent, white and shall be free from foreiga matter. 3.2 Style and design. All pipets covered by this specification shall be Classes 1, 2, 3, and 4 fabricated from polystyrene (see 3.1.1). a piece of

11、cotton (see 3.1.2) 5/8 f 1/8 inches loag. pipets shall be cylindrical in shape and shall be of one piece construction with a gradual tapered dslivery tube at one and and a mouth piece at the other. The delivery tube shall have no sudden constriction at the orifice. Classes 5 and 6 pipets shall be cy

12、lindrical in shape with a delivery tip at one end and mouth piece at the other end. The delivery tip shall be formed by gradual taper and without any sudden constriction at the orifice. delivery tip and the mouth piece shall be either an integral part of the pipet or they shall be individually forme

13、d and permanently attached to the body of the pipet. not more then 1-5/8 in. beyond its point of attachnt,and the-asouth piece shall -chcular; wide band or two thin bands shall be permanently mrked at the mouth erd of those pipets designad to blow out tire last drop. Each pipet shall be plugged with

14、 The When attached to the body, the delivery tube shall extend . _ - - - - -. - _ . _ . -_ .- 3.3-Dimensions. The dimensions for all pipets shall be in accordance -_ with Table I. All dimensions in Table I are exprebscd in inches, Table I. Dimensional Requirements I 1 Overall Class I Length I To ler

15、ance I I I 11 I - # 1/8 I I 1/8 1 2 11 - 8 11 I - + 1/8 # 1/8 11 - 3 I - + 1/8 1 1/8 4 5 6 I I 1 13- 3/4 I 13-3/4 - I I - 3- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.4 Graduation markings. 3.4.1 Class 1. The noininal capacity.for class 1 pip

16、ets shall be 1.0 ml. and shall be ungraduated. 3.4.2 Class 2. Class 2 pipets shall have a 1.0 ml capacity and shall be graduated and numbered at every 0.1 ml. 3.4.3 Class 3. Class 3 pipets shall have a 1.0 ml capacity and shall be graduated in 0.01 ml increments with a longer graduation at 0.05 rnl

17、mark and numbered at every 0.1 ml graduation only to the 0.9 ml graduation mark. 3.4.4 Class 4. Class 4 pipets shall have a 1.1 ml capacity and shall be graduated and numbered at 0.5, 1.0 and 1.1 ml marks. 3.4.5 Class 5. Class 5 pipets shall have a 5.0 ml capacity and shall be graduated in 0.1 ml in

18、crements with major graduations numbered at every 1.0 only to the 4.0 ml graduation mark. 3.4.6 Class 6. Class 6 pipets shall have a 10.0 ml capacity and shall be eaduated in 0.1 ml increments with the major graduations numbered only to the 9.0 ml graduation mark. 3.5 Accuracy. Exce t for class 1 pi

19、pets, all pipets shall be calibrated -_ . , . -: .-i , . .=. 1 c. -Review activities: g Arpry-M) mvy-MS . . Air Force - 03 .- - I. -. _. . . . . .- . _- . - Preparilag activity: . Defense Supply ageacy - DM Beview information is current as of the chte of this document. future coordination of changes to thio (tocusemt, draft circulation should be based on the isfomatioa im the current DODISS. For - -16- . t Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-