DLA MIL-S-24948 A-1993 SLACKS WOMEN-S (WITH SIDE POCKETS)《(带侧口袋)女式运动裤》.pdf

1、MIL-S-2494BA W 99999Ob 1747318 bbb MIL-S-24948A 10 Februarv 1993 SUPERSEDING 29 Sept. 1989 MIL-S-24948 MILITARY SPECIFICATION SLACKS, WOMENS (WITH SIDE POCKETS) This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification

2、 covers the requirements for womens side pocket slacks with straight and bell bottom legs. 1.2 Classification. The slacks shall be of the following types, classes and sizes (body types and lengths) (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which ma

3、y be of use in improving this document should be addressed to: Defense Personnel Support Center, Clothing and Textiles Directorate, Attn: DPSC-FSSD, 2800 South 20th Street, Philadelphia, PA 19101-8419, by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of

4、this document or by letter. FSC 8410 AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1. MIL-S-24948A .1 Types. Type I - Straight leg Type II - Bell bottom leg

5、1.2.2 Classes. Class 1 - Polyester, White 3006 Class 2 - Pol$ester/cotton, White 3053 Class 3 - Polyester/wool, Blue 3346 Class 4 - Polyester/cotton, Khaki 3729 1.2.3 Sizes. Bodv type Juniors - J Misses - No designation Womens - W Petite (P) 4 6 8 10 12 14 16 18 20 Petite PI 6 8 10 12 14 16 18 Petit

6、e (PL 10 12 14 16 Schedule of sizes Misses Reqular (RI 4 6 8 10 12 14 16 18 20 Womens Reqular (R) 6 8 10 12 14 16 18 Juniors Reqular (RI 10 12 14 16 2 Lenqth Petite (Short) - P Regular - R Tall (Long) - T Tall /TI 4 6 8 10 12 14 16 18 20 Tall (T) 6 8 10 12 14 16 18 Tall (T) 10 12 14 16 Provided by I

7、HSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-2494A W 9999906 1747320 214 W MIL-S-24948A 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part o

8、f this document to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL

9、 A-A-50 18 6 A-A-5 2 O 94 V-F-106 NN-P-71 DDD-L-20 MILITARY A-A-5 O 19 9 MIL-P-15011 MIL-B-17757 MIL-C-24910 MIL-C-29127 MIL-C-43718 MIL-C-87052 MIL-C-87059 STANDARDS FEDERAL FED-STD-191 FED-STD-751 Cloth, Buckram, Woven and Non-Woven Thread, Cotton Fasteners, Slide, Interlocking Pallet, Material Ha

10、ndling, Wood, Label; for Clothing, Equipage, and Stringer, 2 way and 4 way (Partial) Tentage (General Use) Thread, Polyester Core: Cotton-, Pallet, Material Handling, Wood, Post Boxes, Shipping, Fiberboard (Modular Cloth, Tropical: Polyester and Wool Cloth, Twill, Polyester/Cotton (Crease Cloth, Pol

11、yester; Polyester and Cotton, Cloth, Twill, Polyester, White Cloth, Nylon, Tricot or Polyester-Covered Construction, 4 Way Entry Sizes) Resistant Finish) Polyester and Rayon, for Pockets Textile Test Methods Stitches, Seams, and Stitchings 3 Provided by IHSNot for ResaleNo reproduction or networking

12、 permitted without license from IHS-,-,-MIL-S-2494A W 9999906 1747321 150 MIL-S-24948A MILITARY MIL-STD-105 Sampling Procedures and Table for MIL-STD-129 Marking for Shipment and Storage MIL-STD-147 Palletized Unit Loads MIL-STD-656 Provisions for Evaluating Quality of MIL-STD-2073-1 DoD Materials P

13、rocedures Development and MIL-STD-2073-2 Packaging Requirement Codes Inspection by Attributes Slacks, Womens Application of Packaging Requirements (Unless otherwise indicated, copies of federal and military specifications, standards and handbooks are available from the Standardization Documents Orde

14、r Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the iss

15、ue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Applications fo

16、r copies should be addressed to the American Trucking Association, ATTN: Traffic Department, 1616 P Street, N.W., Washington, DC 20036-1404.) UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Applications for copies should be addressed to the Uniform Classification Committee, R

17、oom 1106, 222 South Riverside Plaza, Chicago, Illinois 60606-5808.) THE COLOR ASSOCIATION OF THE UNITED STATES Department of Defense Standard Shades For Sewing Threads Department of Defense Standard Shades For Buttons (Applications for copies should be addressed to the Color Association of the Unite

18、d States, 409 W 44th St., New York, NY 10016-0927). 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-S-24748A Ob 1747322 097 I 3.3 Material. MIL-S-24948A 3.3.1.2 Class 2 slacks. The material for the class 2 slacks I shall be a polyester/cotton

19、twill conforming to MIL-C-29127, I shade White 3053. l I I I I I I shade Khaki 3729. 3.3.1.3 Class 3 slacks. The material for the class 3 slacks shall be a polyester/wool tropical conforming to MIL-C-24910, shade Blue 3346. 3.3.1.4 Class 4 slacks. The material for the class 4 slacks shall be a polye

20、ster/cotton twill conforming to MIL-C-29127, I TECHNICAL MANUAL OF THE AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS O Method No. 135 - 1987 - Dimensional Changes in Automatic Home Laundering of Woven and Knit Fabrics (Applications for copies should be addressed to the AATCC National Headqu

21、arters, P.O. Box 12215, Research Triangle Park, NC 27709-9989). (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the . documents. These documents also may be available in or through libraries or other informational services.) .

22、 . 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIRE

23、MENTS 3.1 Guide sample. Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). Variations from this specification may appear in the sample, in which case this specification shall govern. 0 3.2 First article. When specified, the contractor shall furnish sample u

24、nit(s) for first article inspection and approval (see 4.3 and 6.2). 3.3.1 Basic material. 3.3.1.1 Class 1 slacks. The material for the class 1 slacks shall be a texturized polyester twill conforming to MIL-C-87052, shade White 3006. 5 Provided by IHSNot for ResaleNo reproduction or networking permit

25、ted without license from IHS-,-,-nIL-S-24948A 9999906 1747323 T23 = MIL-S-24948A 3.3.2 Liner and Lininq Material. 3.3.2.1 Pockets and left fly lininq. The material for the pockets and left fly lining shall be a twill cloth conforming to class 1 of MIL-C-43718. The color shall be as follows: Class 1

26、and 2 - white Class 3 - dark grey or black Class 4 - unbleached, white, or natural 3.3.2.2 Slack liner. The material for the liner in the class 1 slacks shall be nylon tricot warp knit, shade white 3006, conforming to MIL-C-87059. 3.3.3 Fusible interlininq. The waistband shall be fused with a woven

27、or nonwoven thermal bonded fusible material consisting of 85-100% polyester with the remaining fiber being nylon. The material shall be free of chemical binders. The fusible adhesive system shall be a polyester paste dot uniformly distributed over one side of the material. The color shall be white f

28、or the class 1 and 2 slacks, dark grey or black for the class 3 slacks, and unbleached, white, or tan for class 4 slacks. of the nonwoven fusible shall be 1.1 2 .2 oz/yd . The fused sample, consisting of fusible interlining and base fabric, shall conform to the requirements stated below when tested

29、as specified in Table III. The total weight Component Testinq Requirements Appearance of fused samples L/ Initial 2/ - No evidence of bubbling or delamination of the After 5 launderings 2/ - No evidence of bubbling or After 5 dry cleanings 2/ - No evidence of bubbling or bond, change of color, or st

30、rike through. delamination of the bond, change of color, or strike through. delamination of the bond, change of color, or strike through. Bond strength 3J Initial - 22 oz. minimum After 5 launderings - 18 oz. minimum After 5 dry cleanings - 18 oz. minimum After 3 dry cleanings - 2.5% maximum Shrinka

31、ge After 3 launderings - 2.5% maximum - i/ Applies to quality conformance and in-process tests. 2/ After evaluation for initial appearance and shrinkage, samples may be used for the remainder of the appearance tests. - 3/ When a nonwoven fusible is used, the item will be accepted if the fusible eith

32、er splits from itself rather than separates from the basic material or if it begins to separate from the basic material higher than the minimal bond strength and then splits from itself. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-2474A =

33、 7797706 3747324 9bT MIL-S-24948A 3.3.4 Tape, waistband, non-slip. The woven non-slip tape for the waistband shall be constructed of either polyester or polyester/nylon, natural or white in color, with two rows of chloroprene or nitrile rubber threads, woven or stitched to the tape. The width of the

34、 completed tape shall be 7/8 inch and shall not shrink more than 2% for dry cleaning or 3.5% for laundering when tested as specified in 4.4.1. There shall be a minimum of 3/16 inch from the rubber thread to edge of tape. 3.3.5 Thread polyester covered. Thread for seaming, stitching, and overedging s

35、hall be cotton-covered polyester core, ticket No. 50 and 70, 2 ply; and for button and buttonhole stitching ticket No. 30, 2 ply conforming to A-A-50199. The color of the thread shall be as follows, in accordance with the Standard Shades for Sewing Threads: Class 1 and 2 - White AH, CA# 66050 Class

36、3 - Black AA, CA# 66043 Class 4 - Khaki P-1, CA# 66019 The use of polyester-covered polyester core thread is not allowed. 3.3.5.1 Automatic pocket machine. When an automatic pocket machine using stitch type 101 is used, the thread shall be IC2, ticket No. A, 3 ply conforming to A-A-52094. When an au

37、tomatic pocket machine using a 301 stitch type is used, the thread shall be ticket No. 50, 2 or 3 ply conforming to A-A-50199. The Cable No. Shall be as stated in 3.3.5. 3.3.5.2 Colorfastness. The dyed threads shall show colorfastness to laundering and light equal to or better than the standard samp

38、le when tested as specified in A-A-50199 or A-A-52094. As a minimum level of acceptability, or when no standard sample is available, the thread shall show a minimum of “good“ colorfastness to laundering and light when tested as specified in A-A-50199 or A-A-52094. 3.3.6 Slide fasteners. 3.3.6.1 For

39、class 1 slacks only. The slide fastener shall conform to type I, style la (continuous chain) or 3 (pre- assembled), short tab pull, size LS, of V-F-106. The slide fastener shall be a continuous monofilament nylon or polyester coil. The component parts of the slide fastener shall approximate the colo

40、r of the basic material, of the color of the coil may be clear. The style la (continuous chain) requires the application of a slider and bottom stop during production of the slacks. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. flIL-S-2494BA m 99

41、99906 l17i.17325 BTb m MIL-S-24948A 3.3.6.2 For class 2, 3 and 4 slacks. The slide fastener for the class 2, 3 and 4 slacks shall conform to type I, style 1 or la (continuous) or 3 or 4 (preassembled), short tab pull, size LS, of V-F-106. All metal components of the slide fastener shall be brass, ex

42、cept for the cover and spring on a semi-automatic pin lock which shall be stainless steel. All component parts shall be from the same contractor (see 4.4.1). Style 1 and la require the application of a slider and bottom stop during production of the slack. 3.3.6.3 Color. The color of the slide faste

43、ner tape shall approximate the shade of the basic material 3.3.6.4 Colorfastness. The dyed slide fastener tape shall show colorfastness to laundering equal to or better than the standard sample when tested as specified in V-F-106. As a minimum level of acceptability, or when no standard sample is av

44、ailable, the tape shall show a minimum of “good“ colorfastness to laundering when tested as specified in V-F-106. . 3.3.7 Labels. 3.3.7.1 Combination label. Each pair of slacks shall have a combination identification, instruction, and personal label conforming to type VI, classes 10 and 14 of DDD-L-

45、20. The fastness to laundering requirements of DDD-L-20 shall apply. The inscription shall be as follows; NAME : SERVICE NO: SLACKS, WOMENS (WITH SIDE POCKETS) FIBER CONTENT: 50% POLYESTER/50% COTTON ( EXAMPLE ) CONTRACT NO: DLA-100-00-0-0000 ( EXAMPLE ) NAME OF CONTRACTOR: NAME OF MANUFACTURER: (If

46、 other than contractor) CLASS 1 SLACKS colors. Fill machine with clothes to 2/3 capacity. Use heavy duty soap or detergent. Prespot stains with a laundry stain pretreatment. If needed, use a non-chlorine bleach. Tumble dry using a warm setting or shape and hang dry. Remove at once from dryer. If tou

47、ch-up ironing is needed, use a warm iron. or Follow NAVEDTRA Manual 414-01-45-81, Formula II. Machine wash. Permanent press cycle, hot wash. Do not mix CLASS 2 AND 4 SLACKS Machine Wash - Normal Cycle - Warm Water Do Not Bleach - Tumble Dry Medium Heat - Remove Promptly or Follow NAVEDTRA Manual 414

48、-01-45-81, Formula II. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-249YBA 999990b L74732b 732 W MIL-S-24948A O CLASS 3 SLACKS Machine Wash Permanent Press Cycle - Warm Water (120 F. max) Do Not Bleach - Tumble Dry - Medium Heat - Remove I

49、mmediately May also be Dry Cleaned or Follow NAVEDTRA Manual 414-01-45-81, Formula III. 3.3.7.2 Size label. The size label shall conform to type VI, class 2 of DDD-L-20. The label shall indicate size (body type and length) and stock number, and shall bear the following inscription: SIZE: 14JT (Example- 14 Junior Tall) or 14T (Example - 14 Misses Tall) STOCK NO: 8410-00-000-0000 (EXAMPLE) Note: Abbreviations for