DLA MS35645 REV G-2011 CAP FUEL TANK TACTICAL VEHICLE FORDING.pdf

1、 DETAIL SPECIFICATION SHEET CAP, FUEL TANK: TACTICAL VEHICLE, FORDING Inactive for new design after 22 January 1999. This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this

2、specification sheet. FIGURE 1. Cap, fuel tank: tactical vehicle, fording. ASMC N/A FSC 2910 INCH-POUND MS35645G 09 May 2011 SUPERSEDING MS35645F 20 November 1972 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35645G 2 Inches mm Inches mm Inches mm

3、 Inches mm .125 3.18 .500 12.70 .875 22.23 4.625 117.48 .250 6.35 .750 16.05 3.500 88.90 7.000 177.80 NOTES: 1. Dimensions are in inches. Tolerances are .010 on decimals, 3 on angles. 2. Metric equivalents are given for information only. 3. For design feature purposes, this standard takes precedence

4、 over acquisition documents referenced herein. 4. In the event of a conflict between the text of this specification sheet and the references cited herein, the text of this specification sheet shall take precedence. FIGURE 1. Cap, fuel tank: tactical vehicle, fording Continued. Provided by IHSNot for

5、 ResaleNo reproduction or networking permitted without license from IHS-,-,-MS35645G 3 REQUIREMENTS: This cap is of procurement specification MIL-C-45300, Type II. The cap is to be used with necks shown on MS35644. The chain shall be in accordance with RR-C-271, Type II, class 6. Protective coating:

6、 interior parts shall be cadmium plated in accordance with SAE-AMS-QQ-P-416, Type II, Class 2, or zinc plated in accordance with ASTM-B633, Type II, Fe/Zn 13 (sc 3) 12m minimum, as applicable. Cover surface shall be cleaned in accordance with the applicable method of TT-C-490, then treated with Type

7、 I or III. The surface shall then be primed in accordance with MIL-DTL-53030 and painted in accordance with MIL-E-52891. To move the valve out of closed or open position, the torque shall not be less than 10 inch/ounces. The cap shall withstand a minimum of 25 foot/pounds torque without rotation of

8、cup on inner plate or inner plate on shell. This standard is not intended to limit construction to features other than as shown hereon by dimensions, notations or referenced documents. Part or Identifying Number (PIN). Example of a PIN: MS35645-1 Type of guide and neck (see figure 1) MS prefix and b

9、asic number Example of a PIN: Style Former PIN MS35645-1 Tabs 8333722 MS35645- 2 Knurled None Marking shall consist of the PIN and the manufacturers identification in accordance with MIL-STD-130. Changes from previous issue. Marginal notations are not used in this revision to identify changes with r

10、espect to the previous issue due to the extent of the changes. Referenced documents. This document references the following: MIL-C-45300 MIL-E-52891 MIL-DTL-53030 MIL-STD-130 MS35644 RR-C-271 TT-C-490 ASTM-B633 SAE-AMS-QQ-P-416 Provided by IHSNot for ResaleNo reproduction or networking permitted wit

11、hout license from IHS-,-,-MS35645G 4 CONCLUDING MATERIAL Custodians: Preparing activity: Army AT DLA CC Navy SH Air Force 99 (Project 2910-2010-005) DLA CC Review activities: Army AR, CR4 Navy MC, SA, YD Air Force 71 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-