DOD MIL-C-37106-1974 CASE MEDICAL LABORATORY EQUIPMENT SET《医学实验室装置容器》.pdf

1、- .- - i I: MIL-C-37106 b5 9977706 0463432 3 = fr FIIL-C-37106 1 29 October 1974 IIILITARY SPECIFICATION CASE , MEDICAL LABORATORY EQUIPMENT SET This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 This specification oqvers the requirement

2、s for a nylon carrying case suitable for holding three intermediate rigid containers for the subassemblies of the NSN 6545-00-926-1483 14edical Equipment Set , Medical Laboratory , Combat , Individual. The case is also designed for use with the NSN 8465-00-782-3248 Rucksack, Nylon, Olive Drab 106, V

3、ater-Repellent,. 4 pockets, with adjustable waist belt. 2. APPLICABLE DOCLJMENTS 2.1 The following specifications and standards, of the issue in effect on . date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein: SPECIFICATIONS Federal V

4、-F-106 Fastener, Slide, Interlocking V-T-2 8 5 Thread, Polyester QQ-2-325 Zinc Coating, Electrodeposited, Requirements For PPP-B-585 Box, Wood, Wirebound . PPP-B-601 Box, Wood, Cleated Plywood PPP-B-6 21 Box, Wood, Nailed and Lock Corner PPP-B-6 36 Boxes , Shipping , Fiberboard Military * FIIL-E- 4

5、80 MIL-F- 4 9 5 MIL-B-5 4 3 MIL-IJ- 40 8 8 MIL-S-5 626 MIL-S -6 O 2 9 Enamel, Baking, Phenol-or-Urea-Formaldehyde Finish, Chemical, Black, for Copper Alloys Buckle, Tongueless and Web Strap Webbing, Textile, Woven Nylon Steel, Chrome-Molybdenum (4140) , Bars , Rods , Steel, Chrome-Nickel-Molybiienum

6、 (8740), Bars, Rods, and Forging Stock (For Aircraft Application) and Forging Stock (For Aircraft Application) FSC 6545 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - MIL-C-3710b b5 W 7797906 04b3433 5 W MIL-C- 37106 Filitary (Contd) MIL- E- 2 O

7、6 5 2 PI1 L- E-20 65 2 / 1 1IL-F-2 1840 IIIL- W- 2 i 2 6 5 EIIL-C-4 312 8 STANDARDS b Eyelet, Iletallic, and Eyelet Washers, Iletallic, Eyelets, Iletallic, Rolled Flange Type; and Fastener Tapes, Hook and Pile, Synthetic, Webbing, Textile, Woven Nylon, Impregnated Cloth, Plain Weave, Nylon, Water Re

8、pellent, OG-106 General Specification For Ey !et Washer, General Specification For Federal PED-STD-151 Metal , Test Hethods FED-STD-751 Stitch, Seam and Stitching Fli li t ary MIL-STD- 105 Sampling Procedures and Tables for Inspection IIIL-STD- 129 Marking for Shipment and Storage by Attributes DRAW

9、ING DEFENSE PERSONNEL SUPPORT CENTER 24053 Case, Hedical Laboratory Equipment Set (Copies of specifications, standards, and drawing required by suppliers in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer.) 2.2 O

10、ther publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise indicated, the issue in effect on date of invitation or -ids or request for proposals shall apply. THE COLOR ASSOCIATION OF THE UNITED STATES, INC. United States Army Color C

11、ard of Standard Shades for Slide Fastener Tapes. Department of Defense Standard Color Card of Official 1968 Siandardzed Shades for Sewing Threads (Application for copies of each should be addressed to the Color Association of the United States, Inc., 200 ladison Avenue, New York, N.Y. 10016.) 2 Prov

12、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Y MIL-C-37LOb b5 979470b 0463434 7 W NIL-C-3 7 106 3. REQUIREMENTS 3.1 liaterials Except where otherwise specified, materials shall conform to the applicable portions of the specifications, standards, and d

13、rawing specified herein, and as described in 3.2 and shall be capable of meeting the requirements specified therein. In addition, the metals shall conform to the chemical requirements of their applicable specifications when tested as specified in section 4, those used shall be of the highest commerc

14、ial quality, and entirely suitable for the purpose intended. When materials to be used are not specifically designated, 3.1.1 Cloth, nylon. The nylon cloth shall be olive green No. 106, water repellent, conforming to MIL-C-43128. 3.1.2 Webbing, nylon. The nylon webbing shall conform to Class 2 of MI

15、L-it-4088 as follows : 314 inch width shall be Type Ia. 1-23/32 inch width shall be Type VIII. 3.1.2.1 Color and finish. The nylon webbing shall be dyed olive drab number 7 to match the standard shade, and shall be resin impregnated conforming to class R of MIL-if-27265. The resin impregnated webbin

16、g shall conform to the applicable requirements of MIL-if-2 7265. 3.1.3 Thread polyester. The thread for all stitching shall conform to type I, class I, sub-cnss 7,; Siz:. F, of V-T-285. The thread shall be dyed olive drab shade S-1, C.I. 66022, except the colorfastness requirements and test methods

17、shall be limited to weathering only. 3.1.4 Fasteners, hook and pile. The hook and pile fasteners shall be Type II, Class 1 of NIL-F-21840. Color shall be green, OG 106; width shall be 518 inch. 3.1.5 Buckle, nonslip. The nonslip buckle shall conform to type V, class 3, size 314 inch of MIL-B-543. 3.

18、1.6 Eyelets and washers. Eyelets shall be M20652/1 - BBE117 and washers shall be 1.120652/1 - BBW101 of MIL-E-20652. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I_ MIL-C-37LOb b5 - 979770b OYb3q35 7 r I 1lIL-C- 37 106 3.1.7 Fasteners, slide. Ex

19、cept as specified herein, the slide fasteners shall conform to V-F-106, type I, style 6, size MHC except that the zipper tape shall be 1 inch wide instead of the 314 inch tape specified. Metal parts shall be brass with a black chemical finish conforming to MIL-F-495. The slider shall be equipped wit

20、h a wire stirrup pull equipped with a thong, The length of the chain shall be as required to effect a smooth and secure closure of the case opening# 3.1.7.1 Tape. The slide fastener tapes shall be vat dyed olive drab shade S, conforming to U.S. Army Color Card of Standard Shades for Slide Fastener T

21、apes, and shall be water repellent and mildew resistant, in accordance with V-F-106. Mildew resistance shall be obtained by using copper-8-quinolinolate only. 3.1.7.1.1 Water repellence. The finished tape shall be tested for water resistance as specified in V-F-106, 3.1.7.2 Salt spray resistance. Th

22、e slide fasteners shall meet the salt spray resistance requirements specified in V-F-106. 3.1.7.3 Idebbing for thongs. Webbing for thongs shall conform to the requirements of V-F-106 for thongs (cotton webbing) except that mildew resistance shall be obtained by using copper-8-quinolinolate only. 3.1

23、.8 Adapter, The 500 pound, quick fit, adapter shall be reversible and in accordance with Drawing. Steel shall be type 4140 of HIL-S-5626, or type 8740 of NIL-S-6049. Finish shall be zinc plate in accordance with Type III, class 2 of QQ-Z-325, followed by bake enameling. . The enamel shall conform to

24、 type I or II of MIL-E-480. The color shall be black. 3.1.9 Stitching sealant. Exterior Stitching shall be sealed by the application of one of the two sealants listed in 6.2, or equal, in accordance with the manufacturers directions. 3.2 Construction. The construction of the case shall conform to th

25、e requirements specified herein and to those shown on Defense Personnel Support Center Drawing 24053. 3.2.1 Stitching, machine. All stitching shall conform to FED-STD-751 as follows: For all stitching except overedge stitching; type 301, 8 to 10 stitches per inch, For ovaredge stitching (single oper

26、ation optional); type 503 or 504, 8 to 10 stitches per inch. For closing seams and overedge stitching (simultaneous operation optional); type.301 in combination with 503, 504 or 502, 8 to 10 stitches per inch. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

27、m IHS-,-,-f MIL- C-3 7 106 All edges of closing seams shall be overstitched. There shall be no lub- rication of the thread by any means prior.to or during sewing. operations requiring box, box with cross stitch, W stitching, straight line tacking or any other design of stitching cited in this specif

28、ication may be performed with an automatic stitching machine provided the requirements for stitch pattern, stitches per inch, size, and types, of thread are met; and at least three or more tying, overlapping, or back stitches are used to secure the ends of stitching. Any of the 3.2.1.1 Type 301 stit

29、ching. Thread breaks in stitching shall be over- stitched not -less than 1 inch at each break. Stitching shall be backstitched not less than 1 inch at the ends, except where ends are turned under in a hem or held down by other stitching. Thread tension shall be maintained so that there will be no lo

30、ose stitching, and the lock will be imbedded in the materials sewed. 3.2.1.2 Overedge stitching. Thread breaks in overedge Stitching shall be overstitched not less than 314 inch at each break. Thread tension shall be maintained so that there will be no loose stitching. 3.2.2 Eyelets and washers. Eye

31、lets shall be securely clinched to the washers, without cutting the material. 3.2.3 Fusing of nylon webbing. All ends of nylon webbing shall be fused after cutting, including bias cuts. 3.3 Harking for identification. Each case shall be legibly and permanently marked with black waterproof ink or pai

32、nt in accordance with the drawing. 3.4 Workmanship. Workmanship shall be first class throughout. Complete cases shall be well made and free from defects which detract from their appearance or may impair their serviceability. 4. QUALITY ASSURNACE PROVISIONS 4.1 Responsibility for inspection. Unless o

33、therwise specified in the contract or purchase order, the supplier is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or order, the supplier may use his own or any other facilities suitable for the performance of the i

34、nspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspect ions are deemed necessary to assure supplies and services conform to prescribed requirements. 5 Provide

35、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ I _-_ I_-.- MIL-C-3710b b5 77777Ob 0463437 2 W i Major Total (Major and llinor combined) MIL-C-37 106 * Inspection AQL (defects per level 100 units) II 2.5 II 6.5 4.1.1 Records. Records of examinations and t

36、ests performed by or for the contractor shall be maintained by the Contractor and made available to the Government, upon the Governments request, at any time, or from time to time, during the performance of the contract and for a period of three years after delivery of the supplies to which such rec

37、ords relate. 4.1.2 Inspection. Inspection, as used in this specification, is defined as both examination (such as visual or auditory investigation without the use of special laboratory appliances or procedures) and testing (determination by technical means of physical and chemical properties) of the

38、 item. 4.1.3 Certificates of quality. Certificates of quality, supplied by the manufacturer of the cloth, fasteners, hardware, tape, and webbing, may be furnished in lieu of actual performance of such testing by the contractor, provided lot identity has been maintained and can be demonstrated to the

39、 Government. The certificate shall include the name of the contractor, the contract number, the name of the manufacturer or supplier, the NSN, the item identification, the name of the component/material, the lot number, the lot size, the sample size, the date of testing, the test method, individual

40、test results, and the specification requirements. 4.2 Quality conformance inspection. The examinations and tests required to assure conformance of those items or lots of items to be offered for acceptance are classified as specified in tables I and I (see 4.2.1 and 4.2.2) and 4.2.3. 4.2.1 Sampling f

41、or examination. 4.2.1.1 Sampling for visual defects. Sampling for visual defects shall be conducted in accordance with TIIL-STD-105. The inspection levels and acceptable quality levels shall be as indicated in table I. Unit of product for examination purposes shall be one case. 6 Provided by IHSNot

42、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-37LOb b5 - 9999906 04b343 4 MIL-C-37106 4 Table II. Classification of Defects Major 10 1 10 2 10 3 10 4 105 10 6 10 7 10 8 109 110 111 112 113 Any component missing. Any required operation omitted or improperly perf

43、ormed. Any hole, cut, tear, mend, patch, or unauthorized splice. Needle chews that may develop into hole. One or more spots or stains of an obviously permanent Seam type other than specified. Stitch type other than specified. Less than 8 stitches per inch. Webbing with frayed or scalloped edges. Har

44、dware components broken or malformed. Burrs or sharp edges on hardware. Finish omitted on hardware. Markings omitted, incorrect, or illegible. nature. Minor 20 1 One or more removable spots or stains clearly noticeable. 20 2 Any part of case pleaced, twisted, or caught in any 20 3 Thread ends not tr

45、immed. 204 Broken or skipped stitch not amounting to an open seam. 205 Thread breaks not backstitched for 1 inch. 20 6 Finish on hardware not uniform. 20 7 Color of markings not uniform. unrelated row of stitching. 4.2.3 Sampling for tests. Sampling for tests shall be conducted in accordance with MI

46、L-STD-105, Inspection Level S-2, Acceptable Quality Level 4.0. Unit of product shall be one case. 4.2.3.1 Sampling for chemical testing of metals. Four ounces of each lot of each metal used in the construction of the cases shall be.selected for the chemical analysis as specified in 4.3.1. 4.3 Tests.

47、 Tests shall be conducted to determine compliance with - specification requirements. 4.3.1 Chemical analysis of metals. The samples selected in accordance with 4.2.3.1 shall be analyzed in conformance with methods 111 or 112 of FED-STD-151. In case of dispute, method 111 shall be used for referee an

48、alysis. 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_I_ MIL-C-37LOb 65 777770b 04b3437 b Examine 4.4 Examination of preparation for delivery. An examination shall be made to determine whether the packaging, packing and marking comply with the r

49、equiremets of section 5. Defects shall be scored as specified in table III. Sampling shall be in accordance with MIL-STD-105. The sample unit shall be one container fully prepared for delivery. The lot shall be the number of containers offered for inspection at one time. The inspection level shall be S-2 with an AQL of 4.0 expressed in terms of defects per hundred units. Defect Containers Contents Markings ?later i als