ECA EIA-364-114-2010 TP-114 COUPLING AND UNCOUPLING FORCE TEST PROCEDURE FOR ELECTRICAL CONNECTORS SOCKETS AND APPLICABLE ACCESSORIES.pdf

1、 EIA STANDARD TP-114 COUPLING AND UNCOUPLING FORCE TEST PROCEDURE FOR ELECTRICAL CONNECTORS, SOCKETS, AND APPLICABLE ACCESSORIES EIA-364-114 OCTOBER 2010 THE ELECTRONIC COMPONENTS SECTOR OF THE ELECTRONIC INDUSTRIES ALLIANCE ANSI/EIA-364-114-2010 Approved: October 11, 2010 EIA-364-114NOTICE EIA Engi

2、neering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper p

3、roduct for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of EIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude

4、their voluntary use by those other than EIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by EIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, EIA does not assume any lia

5、bility to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is considered to have International Standardization implication, but the International Electrotechnical Commission activity has not progressed to the point where

6、a valid comparison between the EIA Standard and the IEC document can be made. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and hea

7、lth practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5207 formulated under the cognizance of the CE-2.0 National Connector Standards Committee. Published by ELECTRONIC INDUSTRIES ALLIANCE 2010 Standards and Technology Department 2500

8、 Wilson Boulevard Suite 310 Arlington, VA 22201 PRICE: call Global Engineering Documents, USA and Canada (1-800-854-7179) International (303-397-7956) All rights reserved Printed in U.S.A. i PLEASE ! DONT VIOLATE THE LAW! This document is copyrighted by the EIA and may not be reproduced without per

9、mission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: Global Engineering Documents 15 Inverness Way East Englewood, CO 80112-5704 or call USA and Canada (1-800-854-7179), International (303-397-7956)

10、ii CONTENTS Clause Page 1 Introduction . 1 1.1 Scope . 1 2 Test resources 1 2.1 Equipment . 1 2.2 Material . 1 3 Test specimen 1 3.1 Description 1 3.2 Preparation 2 4 Test procedure . 2 5 Details to be specified . 2 6 Test documentation . 3 iii (This page left blank) EIA-364-114 Page 1 TEST PROCEDUR

11、E No. 114 COUPLING AND UNCOUPLING FORCE TEST PROCEDURE FOR ELECTRICAL CONNECTORS, SOCKETS AND APPLICABLE ACCESSORIES (From EIA Standards Proposal No. 5207, formulated under the cognizance EIA CE-2.0 Committee on National Connector Standards.) 1 Introduction 1.1 Scope This test procedure establishes

12、a test method to determine the coupling/uncoupling forces required to couple and uncouple circular electrical connectors, sockets and applicable accessories. 2. Test resources 2.1 Equipment 2.1.1 Mounting fixtures that allow the specimens to be mounted in their normal manner. 2.1.2 Torque gages of s

13、uitable range for the test specimen size under test so that the readings will be in the middle 50% of the scale, where possible, with a normal torque scale accuracy of 2%. 2.3 Material Alcohol, isopropyl, AR (analytical reagent) grade and/or lubricants as may be specified in the referencing document

14、. 3. Test specimen 3.1 Description Unless otherwise specified in the referencing document, the test specimen shall consist of a plug and receptacle connector with all applicable contacts inserted in place. Applicable hardware including skirts, hoods, cable clamps, etc. shall be installed. EIA-364-11

15、4 Page 2 3.2 Preparation Unless otherwise specified in the referencing document, the test specimen shall not be lubricated with the exception indicated in 3.2.1. 3.2.1 Test specimens which use contact lubricants as a part of the finished product shall be tested in that state. 3.2.2 Unless otherwise

16、specified in the referencing document, the test specimen shall not be cleaned and shall be tested in their as received state. 3.2.3 Unless otherwise specified in the referencing document, test specimens shall be tested with contacts terminated with their applicable conductors or mounted and/or termi

17、nated to test boards. 3.2.4 If a lubricant is to be applied, said lubricant shall be specified and/or approved by the test sponsor prior to the application process. 4. Test procedure 4.1 The two mating connectors shall be brought to a position where mechanical mating begins and the torque gage is at

18、 zero indication. 4.2 Coupling and decoupling rates if applicable shall be as specified in the referencing document. In the event that rates are not specified, the manufactures recommendation shall be used. Manual coupling may be allowed, unless otherwise specified in the referencing document. 4.3 T

19、he peak torque required for coupling shall be recorded. 4.4 The referencing document or manufactures instructions and/or supplied information shall establish when full coupling has been achieved. Said information shall be included in the test report. 4.5 Unless otherwise specified in the referencing

20、 document, decoupling torque shall be applied to fully unmate the test specimens shall be performed and the peak uncoupling force recorded. 5 Details to be specified The following details shall be specified in the referencing document: 5.1 Number of specimens to be tested 5.2 Measurements to be made

21、; coupling and/or uncoupling torque 5.3 Rates of coupling and uncoupling 5.4 Description of full coupling EIA-364-114 Page 3 5.5 Lubrication or cleaning, if required 5.6 Wire type, gage and length, if applicable. Use of test boards, if applicable 5.7 Applicable hardware 5.8 Torque requirements 5.9 T

22、est conditions, if other than standard atmospheric 6 Test documentation Documentation shall contain the details specified in clause 5, with any exceptions, and the following: 6.1 Title of test 6.2 Specimen description including part number, if applicable 6.3 If applicable, fixturing, gage details an

23、d gage part number 6.4 Test equipment used, and date of last and next calibration 6.5 Values and observation 6.6 Description of coupling or confirmation of test sponsors instructions 6.7 Name of operator and start/finish date(s) of test 6.8 Coupling and uncoupling rates EIA Document Improvement Prop

24、osal If in the review or use of this document, a potential change is made evident for safety, health or technical reasons, please fill in the appropriate information below and mail or FAX to: Electronic Industries Alliance Standards and Technology Department 2500 Wilson Blvd., Suite 310 Arlington, V

25、A 22201 FAX: (703-875-8908) Document No.: Document Title: Submitters Name: Telephone No.: FAX No.: e-mail: Address: Urgency of Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Sign

26、ature: Date: FOR EIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Revision History Revision letter Project number Additions, changes and deletions SP-5207 Electronic Components Association 2500 Wilson Boulevard, Suite 310 * Arlington, VA 22201 * tel 703-907-8021 * fax 703-875-8908 www.ecaus.org