EN 12655-1998 en Gymnastic Equipment - Hanging Rings - Functional and Safety Requirements Test Methods《体操设备 吊环 功能和安全要求 试验方法》.pdf

1、 STD-BSI BS EN 12b55-ENGL LA m lb24bb 073bLbS UT5 Gymnastic equipment - Hanging rings - Functional and safety requirements, test methods The European Standard EN 126551998 has the status of a British Standard ICs 97.220.30 BS EN 12655:1998 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COP

2、YRIGHT LAW BS EN 12666:1998 been prepared under the Products and Services Sector Committee, was published under the authority of the Standards Committee and comes into effect on 16 December 1998 direction of the Consumer Amd No. O BSI 1998 ISBN O 580 30238 5 National foreword Date Text affected This

3、 British Standard is the English language version of EN 126551998. The UK participation in its preparation was entrusted to Technical Committee SW/14, Gymnasium and sports equipment, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible European commit

4、tee any enquiries on the - monitor related international and European developments and promulgate interpretation, or proposals for change, and keep the UK interests informed them in the UK. A list of organizations represented on this committee can be obtained on request to its secrem. Cross-referenc

5、es The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “international Standards Correspondence Index”, or by using the “Find facility of the BSI Standards Electronic Catalogue

6、. A Brish Standard does not purport to include all the necessary provisions of a contra 2) straps; 3) cable; 4) swivel. b) For type 2 (see Figure 2): 1) pair of rings; 2) straps; 3) cable; 4) Pulley; 5) height acljustment fhg point. c) For type 3 (see Figure 3): i) pair of rings; 2) rope; 3) rope us

7、ter, 4) swinging mechanism; 5) height austment fixing point. O ES1 1998 STDmBSI BS EN L2bSS-ENGL 1918 E lb211bb7 073bL74 4b2 = Page 4 EN 12666:1998 1 ring 2 strap (ring attachment) 3 cable 4 pulley 5 height adjustment, futing part Figure 2 - Typical example of type 2 equipment O BSI 1998 STD-BSI BS

8、EN 12b55-ENGL 1798 6 Lb24hb9 073b175 3T7 Page 5 EN 12655:1998 4 1 ring 2 rope 3 rope adjust 4 swinging mechaiocin 5 height adjustment fEing point Figure 3 - Qpical example of type 3 equipment O BSI 1998 STD-BSI BS EN 22b55-ENGL 1996 m Ib2qbL7 073b17b 235 Page 6 EN 126661998 4 Functional requirements

9、 4.1 Rings Rings shall be circdar and have the dimensions shown in Figure4. Dimensions in millimetres 918021 92821 Figure 4 - Dimensions for rings 4.2 Axis of rotation For ail types of equipment each ring shall be able to rotate about its own vertical axis. For type 3 equipment the swinging mechanis

10、m shail allow swinging in the direction of intended use. 4.3 Dimensions AU rings shall comply with the dimensions specified in lble 2 and Fgure 5. The information booklet (see clause 7) shall contain the dimensions required for correct instalkition. O BSI 1998 STD*BSI BS EN LZL55-ENGL 1798 Lb24Lb9 0

11、73bL77 L7L Page 7 EN 12655:1998 bpe 1 2 Table 2 - Dimensions hi max hZ max h3 niin bl min b3 min 64 niin I 5 775 3 O00 - 500 5 1500 1 500 4 O00 5 775 3 O00 2 O00 500 f 5 1500 1500 4 O00 Dimensions in millimetres I I I I I I l 3 I 5 600 13 O00 I 2 O00 I 500 f 5 I 1500 I 1500 1 100000 I- 1 face of nea

12、rest object Figure 5 - Dimensions for gymnastic hanging rings - types 1,2 and 3 O BSI 1998 STD-BSI BS EN 12b55-ENGL 1778 W ib2Libb7 073b178 O08 = Page 8 EN 12655:1998 5 Safety requirements 6.1 General Rings shall comply with the requirements of EN 913, except in so far as they are modified by this E

13、uropean Standard. 6.2 Strength When tested in accordance with 6.1, hanging rings types 1 and 2 shal show no signs of fracture, rupture, defects or release of the acjpstrnent mechanism (if any) when subjected to a vertical force of 4 530 N. When tested in accordance with 6.2, hanging rings shall show

14、 no permanent deformation of more than 10 mm in any direction when subjected to a horizontal force of 775 N for types 1 and 2; and 2 140 N for type 3. NOTE The above mentioned forces have been calculated as follows, using the load factors in accordance with Table B.l of prEN 11761:1996. Calculation

15、of test force Ft (in accordance with annex B of EN 9131996): dynamic factor 1,5 safety factor 1,2 body mass rnb 95 kg 9 10 m/s Ft = 96 X 10 X 1,5 X 1,2 Ft = 1 710 N Calculation of structural integrity for types 1,2 and 3 swing angle a o“ CV load factor vertical F, = cV X Ft, Fv = 2,653 X 1 710 Fv =

16、4 536,6 N chosen 4 540 N Calculation of stability: for type 1 and 2 swing angle a lo“ Ch load factor horizontal h = 7746 N chosen 775 N for type 3 fi = 1,253 X 1 710 4 = 2 142,6 N chosen 2 140 N 5.3 Ring attachments For types 1 and 2 equipment the cable shall not be directly attached to the ring. Fo

17、r type 3 equipment the rope shall be spliced and shall not be swaged or clamped. 5.4 Height of axes For type 3 hanging rings the axes of rotation of the swinging mechanism shall be not more than 5,6 metres above the ground. 5.5 Space between ring sets The distance between ring sets (b2 and b3), in t

18、heir position of intended use, shall be not less than 1 500 nim (see Table 2 and Figure 5). 6 Test methods 6.1 General Unless otherwise specified in the following, the requirements of clauses 4 and 5 shall be verified by measurement, visual examination or practical tests. Before testing the equipmen

19、t shall be assembled according to the manufacturers instructions into a condition similar to the position of use. 6.2 Strength 6.2.1 Vertical tests Carry out the vertical test in accordance with annex B of EN 9131996 and as follows. Apply a vertical force of 4 530 N without shock on the hanging ring

20、s as shown in Figure 6. Note any signs of fracture, rupture, defects or release of the aaustment mechanism. Figure 6 - Points of application of forces for vertical tests O BSI 1998 STD-BSI BS EN L2L55-ENGL 1778 U Lb24bL7 073bL79 T44 Page 9 EN 12655:1998 ! I / / / -ci a) types 1 and 2 Figure 7 - Poin

21、ts of application of forces for horizontal tests 6.2.2 Horizontal tests Carry out the horizontal tests in accordance with annex B of EN 913:1996 and as follows. Apply a horizontal force of 775 N without shock on hanging rings types 1 and 2 as shown in Figure 7a). Apply a horizontal force of 2 140 N

22、without shock on hanging rings type 3 as shown in Figure 7b). Determine any permanent deformation greater than 10 mm. 7 Instructions for use An information booklet shall be provided by the manufacturer/supplier containing the following: - type according to Table 1; - “Not more than one user per ring

23、 set”; - “Do not adjust when in use”; - assembly and adJustment details; - a diagram showing the recommended space for safe operation. 8 Markjng Marking shall comply with EN 913. O BSI 1998 BS EN 12655: 1998 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the inde

24、pendent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that th

25、ey possess the latest amendments or editions. It is the constant aim of BSI to improve the quahty of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the kchnical committee responsible, the id

26、entity of which can be found on the inside front cover. Tel 0181 996 9000. Fax: O181 996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and f

27、oreign standards publications should be addressed to Customer Services. Tel O181 996 7000. Fax: O181 996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Info

28、rmation on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact

29、 the Information Centre. Tek O181 996 7111. Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Memberchip Admjnistration. Tel 0181 996 700

30、2. Fax: O181 996 7001. Copyright Copyright subsists in ail BSI publications. BSI also holds the copyright, in the UK, of the publications of the international stadxdization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retriev

31、al systeni or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the come of implementing the standard, of necessary details such as symbols, and size, type or grade designati

32、ons. Jf these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the ternis may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel 0181 996 7070.