EN 186300-1999 en Sectional Specifications Connector Sets for Optical Fibres and Cables Type MSC《分规范 光纤和电缆连接器组 MSC型》.pdf

1、STD=BSI BS EN LBb300-ENGL ?i111 lib21ibh9 077712 BRITISH STANDARD Harmonized system of quality assessment for electronic components Sectional specification: Connector sets for optical fibres and cables type MSC The European Standard EN IS0 1863001999 has the status of a British Standard ICs 33.180.2

2、0 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 186300: 1999 BS EN 186300:1999 direction of the Electrotechnical Amd. No. Da Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 June 1999 National foreword Comments

3、This British Standard is the English language version of EN 1863001999 published by the European Electronic Components Committee (CECC) of the European Committee for Electrotechnical Standardization (CENELEC). The UK participation in its preparation was entrusted by Technical Committee GEU86, Fibre

4、optics, to Subcommittee GEL/86/2, Interconnecting devices and passive components, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible internationalEuropean committee any enquiries on the interpretation, or proposals for change, and keep the UK intere

5、sts informed; - monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secrew. Cross-references The British Standards which implement international or European publications refe

6、rred to in this document may be found in the BSI Standards Catalogue under the section entitled “Internationd Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a c

7、ontract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 15 and a back

8、cover. O BSI 06-1999 I I ISBN 0 680 32608 X EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 186300 February 1999 ICs 33.180.20 Descriptors: Electronic components, optical fibres, connectors, classifications, dimensions, quality assurance, quality control, tests, routine verification English ver

9、sion Sectional Specification: Connector sets for optical fibres and cables Type MSC Spcification intermdiaire: Rahmenspezifi kation: Jeux de connecteurs pour fibres et cbles optiques Licht wellenleiterka bel Type MSC MSC Typ Steckverbinder fr Lichtwellenleiter und This European Standard was approved

10、 by CENELEC on 1998-01-01. CENELEC members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographicai references concerning such national

11、standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and

12、 notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, S

13、weden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels * 1999 CENELEC - All rights of exploitati

14、on in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 186300: 1999 E ST3-BSI ES EN LOL3OU-ENGL 1779 lh2Ybb9 C779L30 505 Page 2 EN 186300: 1999 CONTENTS Clause Page Foreword 3 CECC - SPECIFICATION SYSTEM 4 SECTION ONE . GENERAL 1 General 5 1.1 Scope . 5 1.2 Related docum

15、ents 5 1.3 Definitions 5 1.4 Safety . 5 1.5 Marking 6 SECTION TWO . REQUIREMENTS 2 Requirements 7 2.1 Classification 7 2.2 Reference components 12 2.3 Gauges 12 SECTION THREE . QUALITY ASSESSMENT PROCEDURES 3 3.2 Quality assessment procedures 13 3.1 Qualification approval 13 3.3 Delayed deliveries .

16、 15 Quality conformance inspection . 14 Page 3 EN 186300: 1 999 Foreword This European Standard was prepared by the Technical Committee CENELEC TC 86BXA, Fibre optic connectors. The text of the draft was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 186300 on 1998-01

17、-01. The following dates were fixed: - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1999-08-01 - latest date by which the national standards conflicting with the EN have to be withdrawn (dw) 1999-08-01 It

18、 is based, wherever possible, on the Publications of the International Electrotechnical Commission. Document numbering for fibre optic connector specifications follows 2.2(1) of CECC O0 700, Sect. IV, in order to permit the issue of more than nine sectional specifications. The approved numbering sys

19、tem applicable to fibre optic connector specifications is illustrated in the diagram on next page. Page 4 EN 186300: 1999 CECC 86 O01 BLANK DETAIL SPECIFICATION ENVIRONMENTAL CATEGORY I * Pro-forma for preparation of detail specifica:ions CECC - SPECIFICATION SYSTEM CECC 86 003 BLANK DETAIL SPECIFIC

20、ATION ENVIRONMENTAL CATEGORY 111 EN 186000-1 GENERIC SPECIFICATION FOR CONNECTORS FOR OPTICAL FIBRES AND CABLES * General * Requirements * Quality assessment procedures * Measurement and environmental test procedures JI CECC 86 XXX SECTIONAL SPECIFICATION CECC 86 300 SECTIONAL SPECIFICATION (Connect

21、or sets type MSC) * General * Requirements * Qualitv assessment Drocedures 9 CECC 86 YW SECTIONAL SPECIFICATION CECC 86 002 BLANK DETAIL SPECIFICATION ENVIRONMENTAL CATEGORY II JI CECC 86 302-002 DETAIL SPECIFICATION CONNECTOR TYPE MSC ENVIRONMENTAL CATEGORY II 1 I CECC 86 301-001 DETAIL SPECIFICATI

22、ON CONNECTOR TYPE MSC ENVIRONMENTAL CATEGORY I * Description of style * * Outline drawingts) * Assessmentlevel(s) * Quality assessment procedures * Test and measurement reauirements Details of variants, appropriate cables, etc. v CECC 86 303-003 DETAIL SPECIFICATION CONNECTOR TYPE MSC ENVIRONMENTAL

23、CATEGORY Ill I ST!)*SI BS EN 186300-ENGL 1979 lb24bbl 0777133 214 = Page 5 EN 186300: 1 999 SECTION ONE - GENERAL 1 General 1.1 Scope This sectional specification covers a family of single way fibre optic connector sets which are classified as type MSC. Type MSC is a connector set of the plug-adapto

24、r-plug configuration. It features a push-pull coupling mechanism and cylindrical butting ferrules. The optical alignment mechanism is a split sleeve contained within the adaptor. The specification contains the requirements for type MSC connector sets. Detail specifications (DSs) shall be prepared us

25、ing the following pro forma general blank detail specifications (BDSs) associated with the generic specification. For example: - EN 186005 for environmental category V. When completed, the DS(s) applicable to this SS shall be numbered in accordance with CECC O0 700 (Section IV) Issue 1, clause 4.2,

26、as follows. For example: - CECC 86 305-000, Type MSC, environmental category V. 1.2 Related documents The following standards contain provisions which, through reference in this text, constitute provisions of this standard. At the time of publication, the editions indicated were valid. All standards

27、 are subject to revision, and parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards listed below. References made to a specific clause or sub-clause of a standard includes all sub-clauses to the reference unle

28、ss otherwise specified. EN 186000-1 1993 Generic specification: Connector sets of optical fibres and cables Part 1 : Requirements, test methods and qualification approval procedures IEC 60825-1 1993 Safety of laser products - Part 1: Equipment classification, requirements and users guide IEC 60825-2

29、 1993 Safety of laser products - Part 2: Safety of optical fibre communication systems IS0 128 1982 Technical drawings - General principles of presentation 1.3 Definitions All necessary definitions are given in EN 186000-1. 1.4 Safety 1.4.1 Optical Fibre Connectors, when used as part of an Optical F

30、ibre System, may emitproduce potentially hazardous radiation. The manufacturers of connectors are not obliged to mark them as such, but sufficient information should be made available in the manufacturers literature to enable the system designer to assess the degree of hazard. This information shall

31、 be given prominence in the detail specification (DS). .4.2 the assembler, of the necessary safe work practices. The assembly instructions, included in the connector package, shall give a prominent warning to Page 6 EN 186300: 1999 1.4.3 who should refer to IEC 60825-1. As there is no safety guide f

32、or light emitting diodes (LEDs), IEC 60825-1 shall apply to systems using these also. The responsibility for the safe application of the connector lies with the system design engineer, 1.4.4 WARNING DSs should give the following information in a prominent position : “Care should be taken when handli

33、ng small diameter optical fibre, to prevent it puncturing the skin, especially in the eye area. Direct viewing of the end of an optical fibre or a terminated optical fibre, while it is propagating energy is not recommended unless prior assurance has been obtained as to the safe energy of the output

34、level“. 1.5 Marking See 2.6 of EN 186000-1. STD-BSI BS EN LBb300-ENGL 1779 LbZLIbL7 0779335 O97 W Page 7 EN 186300:1999 SECTION WO - REQUIREMENTS 2 Requirements The requirements specified in Section two and Section three of EN 186000 apply. The requirements for connector sets components covered by t

35、his specification are as specified herein and in the relevant DS. 2.1 Classification The connector sets covered by this specification are classified as : Type: - type I: MSC-PC, - type 2: MSC-APC - coupling mechanism: push-pull, NOTE: Type 1 and type 2 are not intended to be used together. Configura

36、tions: - plug i adaptor i plug Arrangements: - kit, - pigtail, - patchcord. Environmental categories: the DS-writer shall select the appropriate BDS for the chosen environmental category. Assessment levels: - level A, - level B, - level C. The mating face dimensions for connector set configurations

37、are given in Figures 1 and 2. The applicable configuration, arrangement, style, variants, climatic category and assessment levels shall be specified in the DS. Page 8 EN 186300: 1999 I *Mechanical Reference Plane 1 L/+p Cou lin Sleeve CROSS SECTION A-A optical datum target optical datum target 1 I D

38、etail A for APC Detail A for PC FERRULE ENDFACE GEOMETRY A-4 t B PROJECTED FROM 6 Figure I : Plug mating-face limit dimensions STD.BSI BS EN Lb300-ENGL 1999 3b29bb9 0777337 7bT m REF A B C D E F G H I J K L M N O P Q R S T U v W AA AB AC AD AE AF EA EB EC ED E EF NOTES: MIN. 1.2485 2,6 46 4.65 4.3 3

39、.3 25 25 6,55 4.2 5.5 2.4 0,6 O, 5 2.6 1 2.55 5.5 4,3 35 2,3 65 4.3 3,85 0.7 0.2 3 22 40 5,O 0.45 0,60 5,O 1,5 - NOM - 8 MAX. 1,2495 2.7 43 4,75 4,4 3,4 35 35 6,65 43 5,6 23 0,9 0,55 2,7 1,1 56 4.5 3,7 2.4 6,6 4,4 3.95 0.9 3,l 23 45 10 0,73 0,70 10.0 1.7 2,9 0,4 Page 9 EN 186300: 1999 NOTES DEGREE D

40、EGREE L 3 2 2.4 2 DEGREE RADIUS, 5 DEGREE RADIUS, 5 1. A chamfer or radius is allowed to a maximum depth of 0,5 mm from the ferrule endface. 2. The coupling sleeve shall be movable toward the right-and the left-directions. These dimensions are given when the coupling sleeve is moved in its most righ

41、t-direction position. 3. The dimension J is given for the plug endface when not mated. Note that the ferrule is movable by a certain axial compression force with direct contacting end faces. and therefore the dimension J is variable. Ferrule compression force shall be 5,5 N to 6.5 N when the positio

42、n of the optical datum target from the datum X is moved in the range of 3,9 mm to 4,l mm. In addition, the dimension J shall become less than 3.25 mm with a relatively large axial compression force. 4. The dimension Q shall be negative when the outer sleeve is in the extreme left position. 5. The do

43、me eccentricity of the spherical polished endface shall be 50 pm maximum. For angled polished endfaces the dome offset shall be measured not only in the nominal position of the ferrule in the plug, but also in the extreme positions while rotated within the plug. Figure I (contd): Plug mating face li

44、mit dimensions Page 10 EN 186300: 1 999 Mechanical reference plane a. AK Cross section A-A Rigid alignment sleeve Resilient alignment sleeve Cross section B-B Figure 2: Adaptor mating face limit dimensions STD-BSI BS EN LBb30D-ENGL 1999 LbZLfbb7 0779137 732 m GRADE MIN (mm) MAX (mm) 1 REF. NOTES 2,

45、Resilient alignment sleeve A B D E F I J K L M N O P Q R S U v W AA AB AC AD AE AF AG AH AI AK AL AM 2 1,2505 MM 1,2515 Rigid alignment sleeve MIN. 2,39 4,8 435 23 3,9 235 - - - 5,65 3,8 3.3 6,7 4,45 4,Ol 0,95 23 1.9 0,3 0.4 1,34 8,7 6,4 13.0 MAX. Page Il EN 186300: 1999 see grade table GRADE TABLE

46、NOTES 1 The dimension F shall become greater than 4,5 mm when a plug is coupled to or removed from the adaptor. 2 The connector alignment feature is a resilient alignment sleeve. The feature must accept a gauge pin to the centre of the adaptor under the condition that another gauge pin is inserted i

47、nto the feature from the other side. The centre of the adaptor IS defined by the right side position of the dimension J. The withdrawal force shall be between 1 N to 2,5 N Figure 2 (contd): Adaptor mating face limit dimensions STD-BSI BS EN lBb300-ENGL 2797 aI Lb24bbS 0779l4 454 Page 12 EN 186300: 1

48、999 2.2 Reference components Reference component(s), if required, shall be defined in the DS. 2.3 Gauges Gauge(s), if required, shall be defined in the DS. STD-BSI BS EN LBb300-ENGL 1977 3bZLibb9 077L41 390 m Page 13 EN 186300:1999 SECTION THREE - QUALITY ASSESSMENT PROCEDURES 3 Quality assessment p

49、rocedures The quality assessment procedures of EN 186000-1 Section three apply. 3.1 Qualification approval 3.1 .I Qualification by fixed sample procedure When specified, the fixed sample procedure shall be in accordance with 3.3.1 of EN 186000-1 The relevant BDS contains the minimum mandatory test and performance requirements for qualification by the fixed sample procedure. The complete set of mandatory test schedules and performance requirements shall be specified in the DS. Qualification approval is granted for the complete range of variants submitted as structur