EN 60512-14-5-2006 en Connectors for electronic equipment - Tests and measurements Part 14-5 Sealing tests - Test 14e Immersion at low air pressure《电子设备用连接器 试验和测量 第14-5部分 密封试验 试验14.pdf

1、BRITISH STANDARDBS EN60512-14-5:2006Connectors for electronic equipment Tests and measurements Part 14-5: Sealing tests Test 14e: Immersion at low air pressureThe European Standard EN 60512-14-5:2006 has the status of a British StandardICS 31.220.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g5

2、5g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 60512-14-5:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2006 BSI 2006ISB

3、N 0 580 48672 9National forewordThis British Standard is the official English language version of EN 60512-14-5:2006. It is identical with IEC 60512-14-5:2006.The UK participation in its preparation was entrusted to Technical Committee EPL/48, Electromechanical components and mechanical structures f

4、or electronic equipment, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BS

5、I Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for i

6、ts correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests

7、informed; monitor related international and European developments and promulgate them in the UK.Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover.The BSI copyright notice displayed in this document ind

8、icates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARD EN 60512-14-5 NORME EUROPENNE EUROPISCHE NORM May 2006 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komit

9、ee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2006 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-14-5:2006 E ICS 31.220.10 English version Connectors for electronic equipment -

10、Tests and measurements Part 14-5: Sealing tests - Test 14e: Immersion at low air pressure (IEC 60512-14-5:2006) Connecteurs pour quipements lectroniques - Essais et mesures Partie 14-5: Essais dtanchit - Essai 14e: Immersion basse pression atmosphrique (CEI 60512-14-5:2006) Steckverbinder fr elektro

11、nische Einrichtungen - Mess- und Prfverfahren Teil 14-5: Prfungen der Dichtheit - Prfung 14e: Tauchen bei Unterdruck (IEC 60512-14-5:2006) This European Standard was approved by CENELEC on 2006-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the c

12、onditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists i

13、n three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrote

14、chnical committees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the U

15、nited Kingdom. Foreword The text of document 48B/1607/FDIS, future edition 1 of IEC 60512-14-5, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as

16、 EN 60512-14-5 on 2006-04-01. This standard is to be read in conjunction with EN 60512-1 and EN 60512-1-100 which explains the structure of the EN 60512 series. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national

17、 standard or by endorsement (dop) 2007-01-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2009-04-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60512-14-5:2006 was approved by CENELEC as a Euro

18、pean Standard without any modification. _ EN 60512-14-5:2006 2 3 EN 60512-14-5:2006 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 14-5: Sealing tests Test 14e: Immersion at low air pressure 1 Scope and object This part of IEC 60512, when required by the detail specification, is use

19、d for testing l connectors within the scope of IEC technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this part of IEC 60512 is to detail a standard test method to assess the effectiveness of the sealing of a connector against ingr

20、ess of water by exposure to low pressure whilst immersed in a salt solution. It is particularly, but not exclusively, suitable for mated connector assemblies. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only

21、the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512-1-1: Connectors for electronic equipment Tests and measurements Part 1-1: General examination Test 1a: Visual examination IEC 60512-3-1: Connectors for elect

22、ronic equipment Tests and measurements Part 3-1: Insulation tests Test 3a: Insulation resistance IEC 60512-4-1: Connectors for electronic equipment Tests and measurements Part 4-1: Voltage stress tests Test 4a: Voltage proof 3 Preparations 3.1 Preparation of specimen The specimen shall consist of a

23、mated pair of connectors with its terminations, wired as specified in the detail specification. All wires and cables shall be either sealed or extended outside the test chamber. 3.2 Equipment A vessel containing a 5 % 1 %, by weight, solution of non-iodized (commercial) salt, in distilled or deionis

24、ed water shall be prepared. No contaminant shall be present which would be likely to, or tend to, affect the wetting characterics of the solution. This vessel shall be placed in a chamber capable of being evacuated to a pressure of 2 kPa. EN 60512-14-5:2006 4 3.3 Lubricant or sealing substance If th

25、e detail specification so requires, the specified lubricant or sealing substance shall be applied in the manner given in the detail specification. 3.4 Mounting If mounting of the specimen is appropriate, it shall be as specified in the detail specification. 4 Method 4.1 Procedure The test shall be c

26、arried out at room temperature; the temperature of the specimen and the solution shall not differ by more than 5 C. The specimen shall be submerged in the solution, in such a way that the uppermost point of the specimen is at least 25 mm below the surface of the solution The chamber pressure shall b

27、e reduced from room ambient to 2 kPa 0,1 kPa within a period of 5 min to 15 min and maintained at that pressure for a minimum of 30 min. The chamber pressure shall then be returned to room ambient within a period of 1 min and maintained at that pressure for a minimum of 30 min. This constitutes one

28、cycle. Two additional, identical, cycles shall be carried out. During all three cycles, for the period of intervention and subsequent testing, the specimen shall remain submerged as described above. 4.2 Measurements 4.2.1 Initial measurements Visual examination according to IEC 60512-1-1 shall be ca

29、rried out. There shall be no defects, which would impair the validity of the test. 4.2.2 Test measurements and requirements These tests shall be carried out before the specimen is removed from the salt solution. After testing given in 4.1, insulation resistance in accordance with IEC 60512-3-1 shall

30、 be measured. It shall not be less than that given in the detail specification. After the above test, a voltage proof test in accordance with IEC 60512-4-1 shall be carried out. It shall not be less than that given in the detail specification. 4.2.3 Final measurements Visual examination according to

31、 IEC 60512-1-1 shall be carried out with 10 magnification. Any defects, which would impair the normal functioning of the connector, shall be documented. Special attention shall be given to a) evidence of ingress of the solution; b) evidence of dielectric breakdown. 5 EN 60512-14-5:2006 5 Details to

32、be specified When this test is required by a detail specification, the following shall be given therein: a) preconditioning, if required; b) wiring of the specimen; including wire/cable size and type; c) sealant and/or lubricant to be applied, means and quantity; or state Sealant and/or lubricant no

33、t required; d) minimum value of insulation resistance (after this test); and method; e) proof voltage and maximum permitted leakage current; NOTE The values for d) and e) may be given as a requirement after this test and not be identical to those required for an untested specimen. Measurement test p

34、oints should be given in the detail specification. f) any deviation from the standard test method. _ EN 60512-14-5:2006 6 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for th

35、e application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the re

36、levant EN/HD applies. Publication Year Title EN/HD Year IEC 60512-1-1 1)Connectors for electronic equipment - Tests and measurements Part 1-1: General examination - Test 1a: Visual examination EN 60512-1-1 20022)IEC 60512-3-1 1)Connectors for electronic equipment - Tests and measurements Part 3-1: I

37、nsulation tests - Test 3a: Insulation resistance EN 60512-3-1 20022)IEC 60512-4-1 1)Connectors for electronic equipment - Tests and measurements Part 4-1: Voltage stress tests - Test 4a: Voltage proof EN 60512-4-1 20032)1)Undated reference. 2)Valid edition at date of issue. blankBS EN 60512-14-5:200

38、6BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are u

39、pdated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this Briti

40、sh Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically r

41、eceive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www

42、.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international stand

43、ards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing me

44、mbers of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regardin

45、g online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internatio

46、nal standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does

47、 not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.