EN 60512-15-8-1995 en Electomechanical Components for Electronic Equipment - Basic Testing Procedures and Measuring Methods - Part 15 Mechanical Tests on Contacts and Terminations .pdf

1、 STD.BSI BS EN b05LZ-L5-8-ENGL 1777 Lb24bb7 0577409 BRITISH STANDARD Electromechanical components for electronic equipment - Basic testing procedures and measuring methods Part 15. Mechanical tests on contacts and terminations Section 8. Test 15h. Contact retention system resistance to tool applicat

2、ion * * Lo The European Standard EN 60512-15-8 : 1995 has the status of a British Standard ICs 31.220.01 73b BS EN 1997 1995 60512-15-8 : IEC 512-15-8 : NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW STD-BSI BS EN b0512-35-8-ENGL 1777 3b24bbS 0577430 458 AmdNo. BS EN 60612-15

3、-8 : 1997 Date Ted affected Committees responsible for this British Standard The preparation of this British Standard was entrusted by Technical Committee EPU48, Electromechanical components for electronic equipment, to Subcommittee EPUM, Connectors for electronic equipment, upon which the following

4、 bodies were represented: Association of Manufacturers Allied to the Electrical and Electronic Industry British Telecommunications plc BSI Quality Assurance Federation of the Electronics Industry Mhustry of Defence premises Cabling Association Ld) This British Standard, having been prepared under th

5、e direction of the Eledrotechnicai Sector Board, was published under the authority of the Standards Board and comes into effect on 15 March 1997 O BSI 1997 The foiiowing BSI references relate to the work on this standard: Committee reference EPUM Announced in BSI Update February 1997 ISBN O 680 2731

6、1 3 STD-BSI BS EN b0512-15-8-ENGL 1997 = lbZqbb9 0599Ll11 37Li = BS EN 60512-16-8 : 1997 Contents Committees responsible National foreword page Inside front cover ii Foreword Text Of EN 60512-154 2 3 1 National foreword This Section of BS EN 60512 has been prepared by Subcommittee EPU48/2, and is th

7、e English language version of EN 60512-15-8 : 1995 Electmchnicai cmnponents for elechvnic equipment - Bask testing pmcedures and mmri methods - Part 15: Mechunical tests on contacts and terminations - Section 8: Test 15h: Contact retention system resistance to tool applkation, published by the Europ

8、ean Committee for Electrotechnical Stan basic testing procedures and measuring methods - Part 2: General examination, electrical continuity and contact resistance tests, insulation tests and voltage stress tests Amendment 1 (1994) IEC 51 2-8: 1 993, Electromechanical components for electronic equipm

9、ent; basic testing procedures and measuring methods - Part 8: Connector tests (mechanical) and mechanical tests on contacts and terminations NOTE - This series of documents is in process of being revised: the future numbering Is referenced in brackets later in this standard. 3 Preparation of specime

10、ns The specimens shall be fitted with all their contacts, wired in accordance with the detail specification. 4 lest method For each test method described, five contacts shall be tested. Separate contact cavities shall be used for method 1 and for method 2. STDmBSI BS EN b0512-15-8-ENGL 1777 m 1b2qbb

11、S 0599LiLb 97b m Page 4 EN 60512-15-8 : 1996 Method 1 : Rotation of the extraction tool The specified extraction tool shall be introduced into a cavity containing the contact. An axial load as specified in the detail specification shall be applied and maintained while alternating rotations of the to

12、ol are carried out as shown in figure 1. The contact shall then be extracted with the extraction tool, and then reintroduced with the appropriate insertion tool. This operation shall be carried out three times on each of the five contacts. Method 2: Rotation of the insertion tool The contact shall f

13、irst be withdrawn and reinserted into its cavity using the insertion tool on which an axial load as specified in the detail specification is applied. With this load maintained, alternating rotations, as shown in figure 1, shall be carried out. The tool is then extracted and the contact withdrawn wit

14、h the extraction tool. This operation shall be carried out three times on each of the five contacts. If a tool is damaged during the test, a new tool shall be used. 5 Final measurements The specimens shall be subjected to the following tests, if applicable: - visual examination (test la of IEC 512-2

15、 IEC 512-1-1 I); - contact retention in insert (test 15a of IEC 512-8 IEC 512-15-11). 6 Details to be specified When this test is required by the detail specification, the following details shall be specified: a) type and size of wire used; b) tool for insertion of contacts; c) tool for extraction o

16、f contacts; d) axial load to be applied on the tool for methods 1 and 2; e) value of contact retention force. STD*BSI BS EN b0532-15-8-ENGL 3997 m 1b29bbS 0577437 802 m Page 5 EN 60512-15-8 : 1995 I mcm Figure 1 - Alternating rotations of the tool EN 60612-16-8 : 1996 Annex ZA (normative) Normative

17、references to international publications with their corresponding European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate piaces in the text and the publications are listed he

18、reafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undakd references the latest edition of the publication referred to applies (including amendments). NOTE. When

19、the international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year IEC 512-2 1985 Al 1994 EC 5128 1993 litle ENBD Electromechanzcal components for Fax: O181 996 7400. BSI offers members an individual updating service called PLUS

20、which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services, Sales Department at Chiswick Tek 0181 996 7000; Fax: O181 996 7001. In response to or

21、ders for international stan-, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library,

22、 the Standarhe Database, the BSI Information Technology Service ITS) and its Technical Help to Exporters Service. Contact the Information Department at Chiswick Tel 0181 996 7111; Fax: O181 996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial d

23、iscounts on the purchase price of standards. For details of these and other benefits contact Customer Services, Membership at Chiswick Tel 0181 996 7002; Fax: 0181 996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the inte

24、rnational standar-on bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrievai system or transmitted in any form or by any means - elecronic, photocopying, recording or otherwise - without prior written permission from BSI. This

25、 does not preclude the free use, in the com of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager, BSI, 389 Chiswick High Road, London W4 4A.L ISBN O 580 27311 3 EPW48/2