EN 60838-2-1-1996 en Miscellaneous lampholders - Part 2 Particular requirements - Section 1 Lampholders S14 (Incorporates Amendments A1 1998 and A2 2004 Incorporating Corrigendum M.pdf

1、BRITISH STANDARD BS EN60838-2-1:199 IEC 60838-2-1:1994IncorporatingAmendments Nos. 1 and 2Miscellaneous lampholders Part 2-1: Particular requirements Lampholders S14ICS 29.140.10nullnull nullnullnullnullnullnullnull nullnullnullnullnullnullnull nullnullnull nullnullnullnullnullnullnullnullnullnull n

2、ullnullnullnullnullnull nullnull nullnullnullnullnullnullnullnullnull nullnull nullnullnullnullnullnullnullnullnull nullnullnullIncorporating corrigendum May 20136National forewordThis British Standard is the UK implementation of EN 60838-2-1:1996, including amendment A1:1998 and amendment A2:2004.

3、It is identical to IEC 60838-2-1:1994, including amendment 1:1998 and amendment 2:2004 and incorporating corrigendum May 2013.The UK participation in its preparation was entrusted by Technical committee CPL/34, Lamps and Related Equipment to CPL/34/2, Lamp caps and holders.This publication does not

4、purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.BS EN 60838-2-1:1996This British Standard, havingbeen prepared under thedirection of theElectrotechnical S

5、ector Board,was published under theauthority of the StandardsBoard and comes into effect on15 March 1997Amendments/corrigenda issued since publicationAmd. No. Date Comments 10469 July 1999 Changes to subclause 12.515462 24 December 2004 Changes to subclauses 16.2 and 16.330 April 2014 Implementation

6、 of IEC corrigendum May 2013: Clause 16.2, note deleted. BS identifier updated to match CENELEC date of publication.ISBN 978 0 580 83245 1 The British Standards Institution 2014. Published by BSI Standards Limited 2014EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 60838-2-1September 1996 + A1Dece

7、mber 1998+ A2November 2004ICS 29.140.10Descriptors: Lamp, incandescentlamp, lampholder,definition, part icular specification, safety, test conditions , marking,classification,protection against electrical shocks,electric terminal, electrical earthing, protection against moisture, insulation resistan

8、ce,voltage test, mechanical resistance, creepage distance, clearance, heat resistanceEnglish versionMiscellaneous lampholders Part 2: Particular requirements Section1:Lampholders S14(includes amendments A1:1998 and A2:2004)(IEC 60832-2-1:1994 + A1:1998 + A2:2004)Douilles diverses pour lampes Partie

9、2: RglesparticuliresSection 1: Douilles S14(inclut les amendements A1:1998 et A2:2004)(CEI 60838-2-1:1994 + A1:1998 + A2:2004)SonderfassungenTeil 2: Besondere AnforderungenHauptabschnitt 1: LampenfassungenS14(enthlt nderungen A1:1998 undA2:2004)(IEC 60838-2-1:1994 + A1:1998 + A2:2004)This European S

10、tandard was approved by CENELEC on 1996-07- 22,amendment A1 was approved by CENELEC on1998-08-01, and amendment A2was approved by CENELEC on 2004-10-01. CENELEC members are bound tocomply with theCEN/CENELEC Internal Regulations which stipulate theconditions for giving this European Standard the sta

11、tus of a nationalstandardwithout any alteration.Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to anyCENELEC member.This European Standard exists inthree official versions (English, French,German). A vers

12、ion in any other language made by translation under theresponsibility of a CENELEC member into its own language and notified to theCentral Secretariat has the same status as the official versions.CENELEC members are the nationalelectrotechnical committees of Austria,Belgium, Cyprus, Czech Republic,

13、Denmark, Estonia, Finland, France,Germany,Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.CENELECEuropean Committee for Electrotechnical StandardizationComitEuropen

14、de Normalisation ElectrotechniqueEuropisches Komitee fr Elektrotechnische NormungCentral Secretariat: rue de Stassart 35, B-1050 Brussels 1996 Copyright reserved toCENELEC membersRef. No. EN60838-2-1:1996 + A1:1998 + A2:2004 EIncorporating corrigendum May 20132ForewordThe text of the International S

15、tandard IEC 838-2-1:1994, prepared by SC 34B, Lamp capsand holders, of IEC TC 34, Lamps and relatedequipment, was submitted tothe formal vote andwas approved by CENELEC as EN 60838-2-1 on1996-07-02 without any modification.The following dates were fix ed:For products which have complied with the rel

16、evant national standard before 1997-06-01, as shown bythe manufactuer or by a certificationbody, this previousstandard may continue to apply for production until 2002-06-01.Annexes designated “normative” are part of the body of the standard.In this standard, Annex ZA is normative.Annex ZA hasbeen ad

17、ded by CENELEC.Endorsement noticeThe text of the International Standard IEC 838-2-1:1994 was approved by CENELEC as a European Standard without any modification.Foreword to amendment A1Thetext of document 34B/779/FDIS, futureamendment 1 to IEC 60838-2-1:1994, prepared bySC 34B, Lamp caps and holders

18、, of IEC TC 34, Lampsand related equipment, was submitted to the IEC-CENELEC parallel vote and was approvedby CENELEC as amendment A1 to EN60838-2-1:1996 on 1998-08-01.The following dates were fixed:Endorsement noticeThe text of amendment 1:1998 to the International Standard IEC 60838-2-1:1994 was a

19、pproved byCENELEC as anamendment to the European Standard without any modification.Foreword to amendment A2The text of document 34B/1153/FDIS, futureamendment 2 to IEC 60838-2-1:1994, prepared bySC 34B, Lampcaps and holders, of IEC TC 34, Lamps and related equipment, was submitted to theIEC-CENELEC

20、parallel vote and was approved byCENELEC as amendment A2 to EN 60838-2-1:1996 on 2004-10-01.The following dates were fixed:Endorsement noticeThe text of amendment 2:2004 to the InternationalStandard IEC 60838-2-1:1994 was approved byCENELEC as an amendment to theEuropean Standard without any modific

21、ation.latest date bywhich the ENhas to be implemented atnational level by publicationof an identical nationalstandard or by endorsement (dop)1997-06-01latest date by which the national standards conflicting withthe EN have to be withdrawn(dow)1997-06-01latest date bywhich the ENhas to be implemented

22、 atnational level by publicationof an identical nationalstandard or by endorsement (dop)1999-05-01latest date by which the national standards conflicting withthe EN have to be withdrawn(dow)2005-08-01latest date by which the ENhas to be implemented atnational level by publicationof an identical nati

23、onalstandard or by endorsement (dop)2005-07-01latest date by which thenational standards conflicting with theEN have to be withdrawn(dow)2007-10-01EN 60838-2-1:1996CONTENTS1General41.1Scope41.2Normative references42Definitions43General requirement.44General conditions fortests55Standard ratings.56Cl

24、assification57Marking58Protectionagainst electric shock59Terminals .610 Provision forearthing.611 Construction.612 Switched lampholders.613 Moisture resistance, insulation resistance and electric strength714 Mechanical strength .715 Screws, current-carrying parts and connections716 Creepage distance

25、s and clearances.717 Endurance818 Resistanceto heat and fire.819 Resistance to excessive residual stresses(sea son cracking) and to rusting .8 Annex ZA (normative) Normativereferences to international publications withtheircorresponding European publications.93EN 60838-2-1:1996MISCELLANEOUS LAMPHOLD

26、ERS Part 2: Particular requirements Section 1: Lampholders S14 1 General 1.1 Scope This section of IEC 838-2 applies tolampholders S14 intended forbuilding-in as well as forindependent lampholdersfor use with linear incandescent lamps for general lighting service (GLS). Independent lampholders are a

27、lso tested as luminaires.1.2 Normative referencesSee 1.2 of IEC 838-1. 2 Definitions For the purpose of thissection of IEC 838-2, the definitions of IEC 838-1 aswell as thefollowing definitions apply.2.1independent lampholder : lampholder so designed that it can bemounted separatelyfrom a Iuminaire,

28、 while at the same timeproviding all the necessary protection according toits classification and marking.2.2switched lampholder: lampholderprovidedwith an integral switch to control the supplyto the lamp. 3 General requirement Therequirements of clause 3 ofIEC 838-1 apply with the following addition

29、.3.1 Independentlampholders,not specificallyintended for building-in, shall comply with the requirements of the following clauses of IEC 598-1 where these requirements are notcovered by the requirements of thisstandard.Clause 2- ClassificationClause 3 -Marking Clause 4 -Construction (as appropriate)

30、Clause 8-Protection against electric shockClause 9-Resistance to dust, solid objects and moistureClause 10 - Insulation resistance and electric strength (for class II)Subclauses 12.4 and 12.5 - Thermaltests.4EN 60838-2-1:19964 General conditions for tests Therequirements of clause 4 ofIEC 838-1 appl

31、y with the following additions. Add to subclause 4.3: 13 pairs of matching holders intended for lineardouble- capped lamps (for switchedlampholders only) 13 specimens intended for single-capped lamps (for switched lampholderson ly).Afterthe second note, add the following new sentence:3 pairs or thre

32、e specimens:clause 12 ofIEC 838-2-1;NOTE For testing of independent lampholders, not specifically intended for building-in, separateadditionalspecimens are required (see clause 3).5 Standard ratings 5.1 Standard rated voltage is: 250 V.5.2 Standard rated current is:1A.6 Classification The classifica

33、tion of clause 5of IEC 838-1 applieswith the following additions: Add to subclause 5.1: independent lampholders.Add anew subclause 5.3:5.3 According totype: switched lampholders, provided with an integral switch tocontrol the supply to the lamp; non-switched lampholders.7 Marking Therequirements of

34、clause 6 ofIEC 838-1 apply.8 Protection against electric shock Therequirements of clause 7 ofIEC 838-1 apply with the following exception.For lampholders S14,the requirements in the first paragraph of 7.1 apply with the appropriate lampinserted,during insertion or removal of the lamp. NOTE Lampholde

35、rs S14s are not considered as being lampholders for double-ended lamps in the meaning of 7.2.5EN 60838-2-1:19969 TerminalsTherequirements of clause 8 ofIEC 838-1 apply with the following additions.9.1 Lampholders, other than those provided with connecting leads (non-rewireable tai ls),shall beprovid

36、ed with terminals which allow connection of conductors having the followingnominal cross-sectionalareas:0,5 mm to 1,5 mm for lampholdersS14. 9.2 Lampholders with screw-type terminalsshall comply withsection 14 ofIEC 598-1 withthe followingexception.Terminals of the pillar type shall have dimensions

37、not less than those shown forlampholdersE14 in table 4 and 10.5 of IEC 238.Screw-type terminals shall have dimensions not less than those shown forlampholders E14 intable 5 and 10.6 of IEC 238.10 Provision for earthingTherequirements of clause 9 ofIEC 838-1 apply.11 Construction Therequirements of c

38、lause 10 of IEC 838-1 apply with the following additions.11.1 Lampholders S14 provided with a cord anchorageshall comply with the requirements of5.2.10 ofIEC 598-1.11.2 Where provision for cable entry/entriesismade on the accessible external surface ofan independent lampholder,they shall allow the i

39、ntroduction of cable covering, conduitortrunking etc., as appropriate, so asto afford mechanical protection at least for a distance of1 mm measured from the accessible external surface of the lampholder. Compliance is checked by measurement. 12 Switched lampholders12.1 Switches are allowed only in o

40、rdinary lampholders. Compliance is checked by inspection.12.2 Switches used for protection against accidental contact shall be provided with a minimum clearance of 1,7 mm between theopen contacts at different potentials.Compliance is checked by inspection.12.3 Thelampholder shall be so constructed t

41、hat accidental contact between movingpartsof the switchand the supply conductors isprevented.Compliance is checked by a manual test.6EN 60838-2-1:199612.4 The switch operating mem ber shall be effectively insulated from live parts and, ifbroken ordamaged,shall not expose live parts.Compliance is che

42、cked by inspection and by the tests of 12.5.12.5 Switches in lampholders S14 shall be capable of making and breaking a loadcomprising a linearincande scentlamp forgeneral lighting service (GLS).Compliance is checked by the following test.Switches in lampholders S14 without temperature marking shall

43、be tested for an operatingtemperature of 60 C. Switchesinlampholders S14 withtemperature marking shall be tested for operating temperatures equal to the temperature marking minus 20 C.The switchis tested with a.c. (cos = 0,6 0,05) at 1,1 times rated voltage and 1,25 timesrated current. The switch sh

44、all be operated in a normal manner for200 switchmovements atarate of 30 movements per minute at regular intervals.The switch is then tested with a.c. (cos = 1) at rated voltage and current. The switch shallbe operated in a normal manner for20 000 switch mov ements at a rate of 30 movements perminute

45、 at regular intervals.NOTE This test is based on the requirements of IEC 328. Its replacement by the corresponding test of IEC 1058-1is under consideration.Switcheswhich onlyhave the functionto provide protection against electric shock during insertion or removal of the lamp shall beoperatedin a nor

46、mal manner for 1 000 switchmovements at a rate of 30movements per minute.At the conclusion of the test, the lampholder shall withstand the tests specified in subclause11.2 ofIEC 838-1for insulation resistance and electric strength and shall be in satisfactoryworking order.13 Moisture resistance, ins

47、ulation resistance and electric strength The requirements ofclause 11 ofIEC 838-1 apply. 14 MechanicalstrengthThe requirements ofclause 12 ofIEC 838-1 apply. 15 Screws, current-carrying parts and connections The requirements ofclause 13 ofIEC 838-1 apply. 16 Creepage distances and clearances Therequ

48、irements of clause 14 of IEC 838-1 apply with the following additions.16.1 Compliance is checked by takingintoaccount the maximum contact dimensions of the cap.7EN 60838-2-1:199616.2 The clearance between live parts of the lampholder and accessible metal partsof thecap shall not be less than1,5 mm.1

49、6.3 For metal retention springs which are not covered, a minimum clearance of 3 mm t o themounting surface is required. 17 Endurance The requirements ofclause 15 of IEC 838-1 apply. 18 Resistance to heat and fire The requirements ofclause 16 ofIEC 838-1 apply. 19 Resistance to excessive residual stresses (season cracking) and to rusting The requirements ofclause 17 ofIEC 838-1 apply. _ 8NOTEText deletedEN 60838-2-1:19969EN 60838-2-1:199610EN 60838-2-1:1996 BSI 24 December 2004 11List of referencesStandards publicationsBS EN 60061, Sp