FORD ESB-M2E13-A-2003 FIBERBOARD (PANEL) TO BE USED WITH FORD WSS-M99P1111-A 《纤维板（嵌板） 与标准FORD WSS-M99P1111-A一起使用 》.pdf

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action. Revisions 2003 01 29 Revised Para 3.0 inserted ; Para 3.1, 3.2, 3.16, 4 deleted 2002 03 07 Revised Removed ESB-M2E13-B, renumbered & updated D. Whyte 1963 06 28 Released ESB-M2E13-A AS1-960 Printed copies are uncontr

2、olled Page 1 of 3 Copyright 2002, Ford Global Technologies, Inc. FIBERBOARD (PANEL) ESB-M2E13-A PAPERBOARD, KRAFT LINED - BENDING GRADE ESB-M2E13-C PAPERBOARD, KRAFT LINED - BENDING GRADE ESB-M2E13-D 1. SCOPE The materials defined by these specifications are either laminated or cylinder machine buil

3、t-up boards of good composition and suitable construction and may contain a maximum of 13% asphalt in the core ply. The ESB-M2E13-C and ESB-M2E13-D boards have outer plies of virgin kraft paper. 2. APPLICATION These specifications were released originally for materials used for the construction of d

4、eck sides, luggage compartments, front and sides, and other applications specified by engineering. The materials shall be suitable for use as a base for ink decorated, pyroxylin or equivalent coated panel boards. The ESB-M2E13-C and ESB-M2E13-D specifications were released originally for materials u

5、sed for the construction of luggage compartment front and sides where a better bending board was desired in the 1982 T-Bird and XR7 carlines. 3. REQUIREMENTS Material specification requirements are to be used for initial qualification of materials. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS

6、Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 APPEARANCE (FLTM BI 109-01) The color, pattern and finish shall match the approved Design Center master sample, or shall be as specified on the engineering drawing,

7、 or trim patterns (generally one side gray, other side light brown). 3.4 WEIGHT, min 260 lb/1000 ft2(SAE J 315, 0.070 - 0.075 in (1270 g/m2) (1.78 - 1.91 mm) 3.5 SEASONING To minimize warpage, distortions, and dimensional changes, the materials covered by this specification shall be properly seasone

8、d for at least 5 days before being die cut. ENGINEERING MATERIAL SPECIFICATION ESB-M2E13-A ESB-M2E13-C ESB-M2E13-D Page 2 of 3 Copyright 2002, Ford Global Technologies, Inc. 3.6 MOISTURE CONTENT 4 - 9% (ASTM D 644, 4 x 4 in (100 x 100 mm) samples) 3.7 WATER ABSORPTION, max 25% (SAE J 315, 1-1/2 h im

9、mersion) 3.8 WARP, max (FLTM BS 002-01,1-1/2 h water immersion) WMD 5% A 93.9 DIMENSIONAL STABILITY (SAE J 315, Methods “A & C“) Expansion, % max Contraction, % max WMD +0.5 -0.5 AMD +1.5 -1.5 3.10 BURSTING STRENGTH 4 psi/0.001 in (ASTM D 2529, average of 5 bursts (1.1 MPa/mm) on each side of the sp

10、ecimen) 3.11 STIFFNESS, min (ASTM D 747, Tinius Olsen stiffness tester, direct load reading at 5 angle, 2 in (51 mm) span, 2-1/2 lb.in (0.28 N.m) load.) WMD 70 AMD 18 3.12 FIBERBOARD CREASE BENDING TEST (SAE J 119, 180 bend, for test purposes use flat face creasing rule (lightly remove sharp edges w

11、ith a file to prevent cutting) ESB-M2E13-C and No evidence of fiberboard ESB-M2E13-D surface fracture 3.13 STAINING CAUTION: This material may contain a percentage of asphalt and should not be employed in the construction of assemblies employing adhesives, vinyls and fabrics as staining may result.

12、3.14 ESB-M2E13-A and ESB-M2E13-C FLAMMABILITY, max 4 in (101 mm)/min In addition, the test specimen shall not exhibit any flashing or sudden flaming on either surface in excess of the above max value. ENGINEERING MATERIAL SPECIFICATION ESB-M2E13-A ESB-M2E13-C ESB-M2E13-D Page 3 of 3 Copyright 2002,

13、Ford Global Technologies, Inc. 3.15 ESB-M2E13-D ONLY 3.15.1 Flammability In order to comply with Federal Motor Vehicle Safety Standard No. 302, the materials, portions of components, and composites shall not burn, or transmit a flame across its surface, at a rate of more than 4 in (101 mm) per min.

14、To demonstrate compliance, the sample size and method of testing shall be in accordance with FLTM BN 024-02. 3.15.2 Performance - Environmental Aging All materials, portions of components, and composites defined by this specification that have not been treated, modified or reformulated and exceed a

15、max burn rate of 3.0 in (76 mm) per min as specified by the Flammability Lot Sampling Plan of FLTM BN 024-02, must be evaluated for permanency of the materials flame retardant properties per ESB-M25P3-A according to the accelerated environmental aging requirements applicable to the basic material ca

16、tegory of this particular specification. Any material, portions of components, and composites defined by this specification that have been treated, modified or reformulated to conform to Flammability Lot Sampling Plan of FLTM BN 024-02, regardless of max burn rate, must be evaluated for both permane

17、ncy of materials flame retardant properties and changes in mechanical, chemical and physical properties per ESB-M25P3-A applicable to the basic materials category of this particular specification. 3.15.3 Flammability Test Program Materials, portions of components, and composites governed by this specification must also comply with the requirements of ES-D3AB-11014-AA.