FORD ESB-M2E73-C-2002 FELT PAPER - ASPHALT SATURATED - PRESSURE SENSITIVE ADHESIVE ONE SIDE TO BE USED WITH FORD WSS-M99P1111-A 《一侧有压敏胶粘剂的沥青浸渍纸毡 与标准FORD WSS-M99P1111-A一起使用 》.pdf

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2002 10 15 Revised Updated and renumbered 1983 02 23 3.5, 3.7, 3.9 Revised A3D40895/CDM1-MF 502508-1 1981 11 12 Released AM1-6000-66 Printed copies are uncontrolled Page 1 of 3 Copyright 2002, Ford Global Te

2、chnologies, Inc. FELT, PAPER - ASPHALT SATURATED - PRESSURE SENSITIVE ESB-M2E73-C ADHESIVE ONE SIDE 1. SCOPE The material defined by this specification is a paper felt, asphalt saturated with a pressure sensitive adhesive on one side. 2. APPLICATION This specification was released originally for mat

3、erial used as access hole sealers for the 1982 Ford/Mercury. 3. REQUIREMENTS The requirements herein are based on material without release paper unless otherwise specified. 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard

4、Requirements For Production Materials (WSS-M99P1111-A). 3.2 WEIGHT 1.3 +/- 0.1 kg/m2 (ASTM D 461) 3.3 THICKNESS, AS RECEIVED 2.3 +/- 0.2 mm (ASTM D 461) 3.4 ASPHALT CONTENT 12-20 % (ASTM D 461, Trichlorethylene Method) 3.5 WATER ABSORPTION, max 20 g (FLTM BS 4-2, test adhesive surface) 3.6 BREAKING

5、STRENGTH, min (ASTM D 461) WMD 111 N AMD 66 N ENGINEERING MATERIAL SPECIFICATION ESB-M2E73-C Page 2 of 3 Copyright 2002, Ford Global Technologies, Inc. 3.7 STIFFNESS, 30 DIRECT READING, max 82 (ASTM D 747, 25 x 100 mm sample, 50 mm span, 0.08 N.m moment, adhesive side down, avg. of 3) 3.8 FLEXIBILIT

6、Y AT 23 +/- 2 C No cracking when bent 180 around a 51 mm mandrel with the adhesive side to the outside. 3.9 ADHESIVE PERFORMANCE, max 25 mm (Avg. of 3) Test Procedure: The adhesive coated felt paper must support a 70 g dead load in a peel condition over a 71 mm wide area when tested as follows: A Cu

7、t three 71 x 254 mm test specimens and remove release liner. B Bond test specimens to a 76 x 305 mm “E“ coated test panel, allowing a 25 mm overhang. C Roll each test specimen with 910 g +/- 5% (25 mm diameter x 203 mm long) roller, one forward and one return roll. D Firmly press a 70 +/- 2 g (11 x

8、11 x 71 mm) steel bar onto the outermost edge of the exposed adhesive surface. E Suspend each panel so that it is in a horizontal plane with the test specimen bonded to the underside. Expose panels for 24 h at room temperature followed by 24 h at 71 +/- 2C in a mechanical convection oven. F Measure

9、the amount of felt separation from the steel panel. Measure from the front of the steel panel to the felt portion still bonded. 3.10 ODOR Shall be free of obnoxious odors. 3.11 MILDEW RESISTANCE No visual evidence of mildew growth and no mildew odor after 7 days exposure in a humidity cabinet contro

10、lled to 100% R.H. at 38 C ENGINEERING MATERIAL SPECIFICATION ESB-M2E73-C Page 3 of 3 Copyright 2002, Ford Global Technologies, Inc. 3.12 FLAMMABILITY In order to comply with Federal Motor Vehicle Safety Standard No. 302, the materials, portions of components, and composites shall not burn, or transm

11、it a flame across its surface, at a rate of more than 4 in (101 mm) per min. To demonstrate compliance the sample size and method of testing shall be in accordance with FLTM BN 24-2. 3.13 PERFORMANCE - ENVIRONMENTAL AGING All materials, portions of components, and composites defined by this specific

12、ation that have not been treated, modified or reformulated and exceed a max burn rate of 3.0 in (76 mm) per min as specified by the Flammability Lot Sampling Plan of FLTM BN 24-2, must be evaluated for permanency of the materials flame retardant properties per ESB-M25P3-A according to the accelerate

13、d environmental aging requirements applicable to the basic material category of this particular specification Any material, portions of components, and composites defined by this specification that have been treated, modified or reformulated to conform to Flammability Lot Sampling Plan of FLTM BN 24

14、-2, regardless of max burn rate, must be evaluated for both permanency of materials flame retardant properties and changes in mechanical, chemical and physical properties per ESB-M25P3-A applicable to the basic materials category of this particular specification. 3.14 FLAMMABILITY TEST PROGRAM Mater

15、ials, portions of components, and composites governed by this specification must also comply with the requirements of ES-D3AB-11014-AA. 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. This material is not recommended for use in applications that would bring it in contact with trim materials, as staining may occur.