FORD ESB-M4D74-A-2008 POLYETHYLENE HIGH DENSITY INJECTION MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《高密度聚乙烯注塑成型料 与标准FORD WSS-M99P1111-A一起使用 [使用 FORD WSG-M4D901-A1 FO.pdf

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2008 02 29 N-STATUS Replaced by WSG-M4D901-A1 G. Kowalski 2005 01 07 Revised Inserted 3.0; Deleted 3.2.13, 3.3 & 4 1963 08 02 Released AS1-1011 Printed copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 1 of 4 POLYETHYL

2、ENE, HIGH DENSITY ESB-M4D74-A INJECTION MOLDING COMPOUND NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is high density, precolored, polyethylene molding compound. 2. APPLICATION This specification was released originally for materials: Type I Generally used in int

3、erior applications such as cowl side panels and glove box assemblies, or in under-hood applications such as windshield washer reservoirs. Type II Formulated for maximum resistance to weathering and is color matched or color keyed to body exterior colors. This material is specified for exterior appli

4、cations such as valance panels where exposure to direct sunlight is minimal. 3. REQUIREMENTS Note: ESB-M4D74 specification without type designation shall denote Type I only. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard

5、 Requirements For Production Materials (WSS-M99P1111-A). 3.1 RAW MATERIAL (Natural Resin) Type I Type II 3.1.1 Density, g/cm3, min 0.945 0.950 (ASTM D 792) 3.1.2 Flow Rate, g/10 min 20.0 max 10.0 - 20.0 (ASTM D 1238) Note: Flow rate for washer reservoir cap molding resin shall not exceed 5.0 g/10 mi

6、n. 3.1.3 Melting Point, C min 121 121 (FLTM BO 021-02) ENGINEERING MATERIAL SPECIFICATIONESB-M4D74-APrinted copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 2 of 4 Type I Type II 3.2 MOLDED PART Note: Type II samples shall be prepared from finished parts. 3.2.1 Tensile Stre

7、ngth, psi (MPa), min 2800 (19.3) 3200 (22.1) (ASTM D 638, Speed “C“) 3.2.2 Elongation, % min 20 100 (ASTM D 638, Speed “C“) 3.2.3 Hardness Durometer “D“, min 60 55 (ASTM D 2240, instantaneous reading) 3.2.4 Impact Strength, Izod, ft lb/in (J/m), min (ASTM D 256, samples impacted perpendicular to flo

8、w direction) Notched 0.5 (27) 0.5 (27) Unnotched - No break 3.2.5 Heat Resistance (Types I & II) There shall be no visible permanent distortion or color change after the following conditioning: Test Method: The unmounted finished part shall be subjected to 102 +/- 3 C for 3 h in a mechanical convect

9、ion oven. The test specimen shall be shielded from the direct velocity of high temperature air. Allow part to return to room temperature. 3.2.6 Solvent Resistance (Types I & II) There shall be no visible deleterious effects such as cracking, crazing, color changes, or other surface conditions. Test

10、Method: Immerse a 1.0 in (25 mm) portion of a sample, 1 x 3 in (25 x 75 mm) in the solvents listed below for 2 h at 23 +/- 2 C. . Petroleum Naphtha M-14J147 . Trichlorethylene ESF-M5B99 . Kerosene M14J132 . Methyl Ethyl Ketone M14J40 3.2.7 Low Temperature Impact Resistance (Type I only) There shall

11、be no evidence of cracking or any permanent deformation of the assembly. Test Method: Condition the assembly in the cold chamber at -29 C for 5 h. Remove and within 5 s subject sample to impact test by dropping a 2.0 in (50 mm) diameter steel ball weighing 535 g from a height of 4.0 ft (1.22 m). The

12、 ball shall be directed as nearly as possible to the central portion of the test surface. ENGINEERING MATERIAL SPECIFICATIONESB-M4D74-APrinted copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 3 of 4 3.2.8 Environmental Exposure (Type I only) There shall be no evidence of cr

13、acking, crazing, distortion, or color change. 3.2.8.1 Test Method (for washer reservoirs only) The container assembly shall be filled to 3/4 volume capacity with 20% commercial windshield washer solution, covered and subjected to 5 complete cycles of the following: . 3 h at 102 +/- 3 C . 5 h at 23 +

14、/- 2 C . 16 h at -29 C Observations shall be made at the completion of each cycle. 3.2.8.2 Test Method (for other Type I applications) Place a small piece of wood approximately 3 x 3 x 1/2 in (75 x 75 x 13 mm) in intimate contact with a flat portion of the test assembly. Retain by driving a standard

15、 pan head tapping screw 1/2 x 8-15 threads per inch (52726-S or equivalent) through the test material into the wood block. The assemblies shall be subjected to 5 complete cycles of the following: . 3 h at 102 +/- 3 C . 5 h at 23 +/- 2 C . 16 h at -29 C Observations shall be made at the completion of

16、 each cycle for any evidence of cracking, crazing, or distortion. 3.2.9 Impact Strength, Gardner (Type II only), min At 23 +/- 2 C 70 in-lb (7.9 J) At -40 C 100 in-lb (11.3 J) Test Method: Condition several sample parts 0.100 - 0.125 in (2.54 - 3.18 mm) thick for 5 h at the desired test temperature.

17、 Test samples shall be pieces cut from finished (molded-in-color), injection molded parts. A Gardner Impact Unit (model IG-1120) with a 1/2 in (12.7 mm) hemispherical impact head and the corresponding 1/2 in (12.7 mm) diameter steel base plate ring shall be positioned on any minimal energy absorbing

18、 surface. Test samples shall be impacted within 5 s after removal from the temperature conditioning chamber. 3.2.10 Resistance to Weathering (Type II only) In addition to requirements specified below, samples shall exhibit no more than a 40% decrease in tensile strength after exposure to weathering.

19、 ENGINEERING MATERIAL SPECIFICATIONESB-M4D74-APrinted copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 4 of 4 3.2.10.1 Weatherometer (FLTM BO 101-01) The material shall not stain, chalk, exhibit color change or change in hue in accordance with rating 4 of AATCC Gray Scale f

20、or Evaluating Change in Color (10 step) after 1,600 h exposure. 3.2.10.2 Florida Exposure After exposure to Florida weathering (5 South, D.W.I) for 1 year, samples shall not exhibit objectionable color change nor surface degradation. 3.2.11 Appearance The color, pattern, finish, and embossing shall

21、match that of the master sample as approved for production by the Design Center. Each molded color must pass Resistance to Weathering requirements of para. 3.2.10. 3.2.12 Flammability, max 4 in (101 mm)/min (FLTM BN 024-02, without the lot sampling plan) In addition, the test specimen shall not exhi

22、bit any flashing or sudden flaming on either surface in excess of the above maximum value. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 MOLD SHRINKAGE 0.015 in/in (mm/mm) (ASTM D 955) 5.2 COEFFICIENT OF LINEAR THERMAL EXPANSION 8 x 10-5/ E (ASTM D 696) (14.4 x 10-5/ C)