FORD ESD-M6C57-A-2008 BRAKE FLUID - SUPER DOT 4 TYPE TO BE USED WITH FORD WSS-M99P1111-A 《特级DOT4型制动液 与标准FORD WSS-M99P1111-A一起使用 ［使用 FORD WSS-M6C57-A2］》.pdf

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions Ver 5 2008 05 28 N-STATUS Replaced with WSS-M6C57-A2 M. Swain, FOE 2005 02 14 Revised Updated format 1989 11 07 Final release SM/ER5384TC D. Allcock, EAO Printed copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 1 of 7

2、 BRAKE FLUID, SUPER DOT 4 TYPE ESD-M6C57-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a non-petroleum D.O.T.4 type, 180 C minimum W.E.R.B.P. quality, hydraulic brake fluid containing polyalkylene glycol ethers, borate esters and additives. 2. APPLICATION Thi

3、s material is primarily intended for use as a hydraulic fluid in passenger and light commercial vehicle brake systems. 3. REQUIREMENTS Material specification requirements are to be used for initial qualification of materials. 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and

4、part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 QUALIFICATION PROCEDURE 3.2.1 Qualification The Materials Engineering activity reserves the right to subject materials submitted against this specification, to any additional investigatio

5、n they may consider necessary and use the data derived for approval qualification. 3.2.2 Verification The affected Materials Engineering activity reserves the right to conduct verification testing. If the test results do not support the originally submitted data, the supplier must re-test the produc

6、t in coordination with the affected Materials Engineering activity. This re-test must be conducted and certified by a mutually agreed upon test facility. 3.2.3 Documentation Supplier must furnish to the affected Materials Engineering activity a completed and certified copy of the attached Supplement

7、 A and test reports demonstrating full compliance with all the requirements of this specification. All tests must be certified by a qualified and authorized representative of the test facility. ENGINEERING MATERIAL SPECIFICATION ESD-M6C57-A Printed copies are uncontrolled Copyright 2008, Ford Global

8、 Technologies, LLC Page 2 of 7 3.2.4 Chemical and Physical Properties This material shall comply with the requirements of FMVSS No.116 D.O.T.4 with the following additions. (All test methods to FMVSS No.116 unless otherwise indicated). 3.2.4.1 E.R.B.P. minimum 260 C (Equilibrium Reflux Boiling Point

9、) 3.2.4.2 W.E.R.B.P. minimum 180 C (Wet Equilibrium Reflux Boiling Point) 3.2.4.3 Viscosity at -40 C max 1450 mm2/sec 3.2.4.4 Mineral Oil Contamination, V/V max 0.025% (FLTM AM 150-03) 3.2.4.5 Water Content, max 0.20% (ASTM E 203) 3.2.4.6 Corrosion 3.2.4.6.1 Metal Strip Corrosion (This test to be pe

10、rformed both with and without “added“ water in the test fluid). A corrosion test shall be carried out according to SAE J 1703 procedure, but including a zinc test strip additional to the six regular SAE strips. The zinc to be placed at the end of the assembly next to the copper strip. The zinc used

11、shall be SAE 925 alloy. Test pieces can be obtained from Erich Herrmann and Co., 7501 Grotzingen ueber Karlsruhe 2, West Germany. The maximum permissible weight loss for zinc test strip in the test shall be 0.20 mg/cm2 of surface. The test strips outside the contact area shall not be pitted or rough

12、ened to an extent visible to the naked eye. 3.2.4.6.2 Graphite Corrosion Test (Appendix A) Any etching, roughening or pitting visible to the naked eye shall constitute a failure. 3.2.4.6.3 Thermal Stability Corrosion Test After 5 days at 100 C in 1 litre sealed can, fluid shall meet the requirement

13、of corrosion test 3.3.4.6.1. ENGINEERING MATERIAL SPECIFICATION ESD-M6C57-A Printed copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 3 of 7 3.2.4.7 Compatibility Using the procedure described in SAE J1703 but supplement RM66-03 compatibility fluid with other Ford approved b

14、rake fluids, as required. 3.2.4.8 Compliance The brake fluid is an integral component of the hydraulic brake system. Compliance with the requirements of all E.S. Test Specifications as identified by the relevant Product Engineering office is necessary for the approval of any new fluid against this s

15、pecification. 3.2.5 Quality Control Upon engineering approval, supplier and affected Materials Engineering activity shall establish mutually agreed upon quality control limits, to be listed on Supplement B, and will be used for ongoing product verifications at mutually agreed upon frequencies. 4. GE

16、NERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 4.1 ENVIRONMENTAL CONTROL The supplier shall divulge to the company, the identity or nature of any ingredient or constituent of their products which is capabl

17、e of causing pollution of water, air or soil, and/or which is subject to special notification or control under the laws or regulations in force at the locations in which it is to be used or disposed. In addition, the supplier shall, in appropriate cases, make available to the company, details of tre

18、atment methods that will enable used or surplus material to be broken down satisfactorily for disposal through effluent plants. 4.2 HEALTH AND SAFETY This material is potentially harmful unless handled properly. To ensure that appropriate precautions are taken, plant medical and safety units shall b

19、e advised of its intended use in the plant. Areas where this material is to be stored and used shall be clearly marked by signs in accordance with Manufacturing Standards U-SN001. 4.3 DISPENSING Care should be exercised when dispensing this material. Brake fluids damage vehicle body paint and certai

20、n plastics. ENGINEERING MATERIAL SPECIFICATION ESD-M6C57-A Printed copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 4 of 7 APPENDIX A GRAPHITE CORROSION TEST Two shortened SAE cast iron strips are prepared in accordance with SAE J1703. Powdered graphite is applied to the up

21、per surface of the prepared strips to occupy the central area. (Approximately 8 mm x 30 mm to depth of 3 mm). The strips are carefully placed in the test jars (approximately 84 mm OD x 74 mm high) containing 75 ml of the test fluid, (ie fluid under test +5% water +50 ppm chloride derived from NaCl)

22、and the test jars closed with a mild steel lid (without insert pad). The test jars are placed in an oven at 70 2 C for 168 hours (7 days). At the end of the test period each strip is removed, washed in 95% ethanol to remove the graphite, wiped clean and examined for sings of etching or corrosion pit

23、ting under the graphite layer. Any etching, roughening or pitting visible to the naked eye shall constitute a failure. Details of suitable powdered graphite can be obtained from the Materials Laboratory 13/100, Laindon, Basildon, Essex SS15 6EE. ENGINEERING MATERIAL SPECIFICATION ESD-M6C57-A Printed

24、 copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 5 of 7 Supplement A Page 1 of 2 Supplier_ Date_ Product Name_ FMVSS 116 Grade_ Product Code_ Manufacturing Plant Location(s)_ BASE FLUID NOMINAL TYPE SOURCE/CODE VOLUME % A. _ _ _ B. _ _ _ C. _ _ _ D. _ _ _ ADDITIVES Type/ S

25、upplier Function Name Code Carrier % in Final Product A. _ _ _ _ _ B. _ _ _ _ _ C. _ _ _ _ _ D. _ _ _ _ _ Signature_ Title_ ENGINEERING MATERIAL SPECIFICATION ESD-M6C57-A Printed copies are uncontrolled Copyright 2008, Ford Global Technologies, LLC Page 6 of 7 Supplement A Page 2 of 2 Supplier_ Date

26、_ Product Name_ FMVSS 116 Grade_ Product Code_ Manufacturing Plant Location(s)_ Test Mfg. Physical/Chemical/Performance Properties Results Limits FMVSS No 116 D.O.T.4 Requirements Compliance Test Report E.R.B.P. C _ _ (Equilibrium Reflux Boiling Point) W.E.R.B.P. C (Wet Equilibrium Reflux Boiling Po

27、int) _ _ Viscosity at -40 C mm2/sec _ _ Mineral Oil FLTM AM 150-3 _ _ Contamination V/V % Water Content % ASTM E 203 _ _ Corrosion:- Metal Strip Test (with water _ _ Metal Strip Test (without water) _ _ Graphite Crevice Test _ _ Thermal Stability Corrosion _ _ Compatibility _ _ Infra Red Spectrum _

28、_ Flash Point C ASTM D93 _ _ Relative Density at 15 C ASTM D1298 _ _ Elemental Analysis A. _ _ B. _ _ C. _ _ All test methods as per FMVSS No.116 unless otherwise stated. Signature_ Title_ ENGINEERING MATERIAL SPECIFICATION ESD-M6C57-A Printed copies are uncontrolled Copyright 2008, Ford Global Tech

29、nologies, LLC Page 7 of 7 Supplement B Supplier_ Date_ Product Name_ FMVSS 116 Grade_ Product Code_ Manufacturing Plant Location(s)_ QUALITY CONTROL CERTIFICATION Approved Physical/Chemical/Performance Properties Limits Frequency E.R.B.P. C _ _ (Equilibrium Reflux Boiling Point) W.E.R.B.P. C _ _ (We

30、t Equilibrium Reflux Boiling Point) Viscosity at -40 C mm2/sec _ _ Mineral Oil Contamination V/V % FLTM AM 150-03 _ _ Water Content % ASTM E203 _ _ Corrosion _ _ Metal Strip Test (with water) _ _ Metal Strip Test (without water) Graphite Crevice Test Appendix A _ _ Thermal Stability Corrosion Compatibility _ _ Infra-Red Spectrum _ _ _ _ Flash Point C ASTM D 93 _ _ Relative Density at 15 C ASTM D 1298 _ _ Elemental Analysis A. _ _ B. _ _ C. _ _ All test methods as per FMVSS 116 unless otherwise stated. Remarks_ _ SUPPLIERS SIGNATURE_ TITLE: _ MATERIAL ENGINEERING CONCURRENCE:_