FORD ESE-M8G231-A3-2000 GASKET STAINLESS STEEL EPOXY RESIN COATED《环氧树脂涂层的不锈钢垫片》.pdf

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2000 11 08 Revised Updated A. Cockman 1993 09 14 NE01 - E - 10127076 - 098 Rele ased E. J. Duda Printed copies are uncontrolled Page 1 of 3 Copyright 2000, Ford Global Technologies, Inc. GASKET, STAINLESS ST

2、EEL, EPOXY RESIN COATED ESE-M8G231-A3 1. SCOPE The material defined by this specification is a steel laminated gasket which consists of three layers of steel. The block side plate and the cylinder head side plate are coated with a hi gh temperature resistant NBR elastomer on the outside. The middle

3、plate is coated with a high temperature resistant NBR on both sides. 2. APPLICATION This specification was released originally for material requiring exceptional compressive strength as w ell as excellent sealing at high temperatures as required by cylinder head gaskets. 3. REQUIREMENTS Material spe

4、cification requirements are to be used for initial qualification of materials 3.1 QUALITY SYSTEM REQUIREMENTS Material suppliers and part p roducers must conform to the Companys Quality System Requirements. 3.2 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSIS IR spectra and thermograms established

5、 for initial approval shall constitute the reference standard and shall be kept on file at t he designated material laboratory. All samples shall produce IR spectra and thermograms that correspond to the reference standard when tested under the same conditions. 3.3 CONSTRUCTION The gasket consists o

6、f three steel plates coated after assembly wit h an NBR elastomer. The center plate of the gasket is coated on both sides before assembly with a micro thin layer of rubber. 3.4 BLOCK SIDE PLATE 3.4.1 Metal 1008/1010 (SAE J403) ENGINEERING MATERIAL SPECIFICATION ESE-M8G231-A3 Page 2 of 3 Copyright 20

7、00, Ford Global Technologies, Inc. 3.4.2 Hardness, Rockwell B 40 - 55 (ASTM A 370) 3.4.3 Zinc /Zinc Phosphate Coating Weight, min 11.29 gm/m 2 (ASTM A 90, both sides, dry) 3.4.4 NBR Elastomer Coating on One Side 3.4.4.1 Coating Thickness, On Outside 12 - 41 micrometre (ASTM D 1186) 3.4.4.2 Coating M

8、IBG714Z* (ASTM D 2000) 3.5 MIDDLE PLATE 3.5.1 Metal 30301 FH (SAE J405) 3.5.2 NBR Elastomer Coating on Both Sides 3.5.2.1 Coating Thickness, per Side 12 - 41 micrometre (ASTM D 1186) 3.5.2.2 Coating MIBG714Z* (ASTM D 2000) 3.6 CYLINDER HEAD SIDE PLATE 3.6.1 Metal 30304 (SAE J405) 3.6.2 NBR Elastomer

9、 Coating on One Side 3.6.2.1 Coating Thickness, on Outside 12 - 41 micrometre (ASTM D 1186) 3.6.2.2 Coating MIBG714Z* (ASTM D 2000) *Z, Elongation = 150 %, min ENGINEERING MATERIAL SPECIFICATION ESE-M8G231-A3 Page 3 of 3 Copyright 2000, Ford Global Technologies, Inc. 3.7 SUPPLIERS RESPONSIBILITY All

10、 materials supplied to this specification must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved under this specification, whether or not such changes aff ect the materials ability to meet

11、the specification requirements, the Supplier shall notify the affected Purchasing, and Materials Engineering activities (with reasons) of the proposed changes. Upon notification of the Company, further instructions will be provided. Note: Suppliers should be prepared to provide test data and samples

12、 demonstrating compliance to this specification, if requested. Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in Restricted Substance Management Standard WSS - M99P9999 - A1. 4. APPROVAL OF MATER

13、IALS Materials defined by this specification for direct supply to the Company must have prior approval. Certain materials subcon tracted by part suppliers may also require prior approval. These include materials critical to the Companys business for regulatory, safety, environmental or compatibility

14、 requirements or contractual agreements. Suppliers desiring approval of their mate rials shall first obtain an expression of interest from Purchasing, Design or Materials Engineering activity. Upon request, the Supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of this specification.