FORD FLTM AN 101-3-2001 TEST FOR CONTAMINANTS IN TEXTILE MATERIALS (Replaces FLTM EU-AN 001-03).pdf

1、 FORD LABORATORY TEST METHOD AN 101-03 Date Action Revisions 2001 01 30 Revised Editorial no technical change A. Cockman 2000 04 14 Editorial no technical change A. Cockman 1990 06 14 Printed copies are uncontrolled Page 1 of 3 Copyright 2001, Ford Global Technologies, Inc. TEST FOR CONTAMINANTS IN

2、TEXTILE MATERIALS Application This procedure is used to test for residual asphalt and similar objectionable contaminants in textile trim materials which may cause staining of other trim components by being sewn or bonded or by mere contact. Apparatus Required Fadeometer As specified in FLTM BN 101-0

3、1. Plates Two 100 x 100 x 6 mm (nominal thickness) glass or aluminum plates. Weights To provide a total load of 1 kg when placed with the plate on the test assembly. Ventilation Hood Materials Required Nainsook Test Fabric M-99H32A Source: Test Fabrics Inc. Loeffler Filter GMBH P.O. Drawer O, Forsba

4、ck Ueberhoeferfeld 44 200 Blackford Ave. 5064 Roesrath W. Middlesex, NJ 08846 West Germany Westlairds Calico Printers Assn. Ltd. North Green Leith House Datchet Slough, SL39JH, Eng. Gresham St., London E.C.2 Firma Walta Thoma 7888 Rheinfelden/Baden Wehrstrasse 6, Germany FORD LABORATORY TEST METHOD

5、AN 101-03 Page 2 of 3 Copyright 2001, Ford Global Technologies, Inc. Naphtha* M-14J148 or SM142 148A Toluol* M-14J242 or EM14J 200A * CAUTION: Low flash point. Refer to Industrial Hygiene for health and safety comments. Conditioning and Test Conditions All test values indicated herein are based on m

6、aterial conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. Procedure Method A 1. Cut two 100 x 100 mm sections of the nainsook test fabric and two 150 x 150 mm

7、sections of the test specimen. 2. Place one test specimen on each of the two plates and cover with a section of nainsook. (The test specimen - plate - nainsook combination is referred to as a test assembly.) Note: Perform steps 3 - 7 in a ventilation hood. 3. Saturate one test assembly with naphtha

8、and the other with toluol. 4. Place a plate on top of each assembly. 5. Place sufficient weight (when added to the weight of the top plate) to equal a total load of 1 kg and allow to stand for one h at 23 +/- 2 C. 6. Remove weights and plates. 7. Examine each section of nainsook for staining as requ

9、ired by the applicable Engineering Material Specification. FORD LABORATORY TEST METHOD AN 101-03 Page 3 of 3 Copyright 2001, Ford Global Technologies, Inc. Method B 1. Place a sample of trim cover material over a test specimen of padding to simulate its actual application in the vehicle. 2. Place th

10、e assembly into the Fadeometer with the face side of the trim cover material towards the light source. 3. Expose for 120 Standard Fade Hours (black panel temperature of 63 +/- 2 C) as per FLTM BN 101-01. 4. Examine the face side of the trim cover material for any stain and report as required by the material standard. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities.