FORD FLTM BI 159-1-2001 DETERMINATION OF THE RESISTANCE TO FLOTATION OF CONVENTIONAL METALLIC PAINTS (Replaces FLTM EU-BI 059-01).pdf

1、 FORD LABORATORY TEST METHOD BI 159-01 Date Action Revisions 2001 03 20 Revised Editorial no technical change A. Cockman 1992 04 06 Printed copies are uncontrolled Page 1 of 5 Copyright 2001, Ford Global Technologies, Inc. DETERMINATION OF THE RESISTANCE TO FLOTATION OF CONVENTIONAL METALLIC PAINTS

2、Application This method is used to determine the resistance to flotation of conventional metallic paints. Apparatus Required 1. Automatic Spray Equipment - Spraymation Model 9148 a. Spraygun to be De Vilbiss ABG Series 501 Gun, Needle and Tip - AV15EX with No. 30 air cap, or suitable equivalent. b.

3、Air pressure - 450 kN/m2 c. Number of coats - 3 d. Flash-off between coats - 2 minutes 2. Spraybooth - Air Conditioned a. Airflow over panel rack must be 45-60 m/min b. Booth temperature must be 24 +/- 2 C c. Relative Humidity must be maintained at 45 - 64 % 3. Laboratory forced air oven capable of

4、maintaining a constant temperature of 180 +/- 1 C. 4. Macbeth Color Matching Booth, or equivalent, with North Sky Daylight according to FLTM BI 109-01. 5. Thickness gauge - Permascope with constant pressure probe or approved alternative. 6. Test panels: Steel body skin panels with an Ra of 0.9 - 1.8

5、 microns. Test panel size to be 300 mm x 335 mm minimum. FORD LABORATORY TEST METHOD BI 159-01 Page 2 of 5 Copyright 2001, Ford Global Technologies, Inc. Preparation of Test Panels 1. Prime, wet sand and dry test panels as described in FLTM BI 103-02. Mask one (1) edge of test panel to allow enamel

6、film thickness to be measured. 2. Reduce enamel under test to the recommended test viscosity using xylol as the paint solvent. 3. Establish Standard Spraymation settings such as fluid flow, lap distance, etc., such that the application of three (3) coats of enamel at an enamel dry film thickness of

7、45 - 50 microns meets all paint appearance requirements. These settings will then be the standard settings for the paint under test. The flash-off after the final coat should be five (5) minutes with the panel kept in a horizontal position. Note: It may be necessary to alter slightly the standard se

8、ttings to achieve paint appearance requirements if the evaluation is carried out over more than one (1) day. 4. Test Variations in Spraymation Settings Setting 1 Setting 2 Setting 3 a. Fluid Flow FF1 FF2 FF3 b. Gun to panel distance GD1 GD2 GD3 c. Traverse speed TS1 TS2 TS3 Setting No. 1 is the stan

9、dard settings established in Para 3 above. Note: Fluid flows to be established using xylol and increases in fluid flow are also to be made using xylol. Test Variations Flux Flow FF2 = FF1 + 20 mL/min FF3 = FF1 + 40 mL/min Gun Distance GD1 = “B“ Setting, where “B“ = Constant distance for three (3) co

10、ats. GD2 = “C“ Setting, where “C“ = two (2) coats furthest from panel, one (1) coat close to panel. GD3 = “A“ Setting, where “A“ = two (2) coats close to panel, one (1) coat furthest from panel. FORD LABORATORY TEST METHOD BI 159-01 Page 3 of 5 Copyright 2001, Ford Global Technologies, Inc. Traverse

11、 Speed - sec TS2 = TS1 - 4 TS3 = TS1 - 8 Spray a test panel using each of the three (3) variations of the three (3) spraymation settings and bake each panel according to the Engineering Materials Specification requirements. The total number of test panels will be (27). The Standard Spraymation setti

12、ngs (111 series) should be checked during this multiple panel exercise to check the consistency of the equipment and material, and test environment. Evaluation Flotation is the term given to poor aluminum pigment orientation of metallic paints. It manifests itself in the form of dark patches or mott

13、ling on the test panel or sometimes black edging of the test panels. Compare each test panel with the standard setting panel (series 111) for the presence of flotation, by viewing in the Macbeth color cabinet. A subjective assessment of the degree of flotation, e.g. slight, medium or heavy should be

14、 made and the results charted on the Flotation Evaluation Chart by coding the test variants which give flotation. The enamel dry film thickness should also be recorded on the Flotation Evaluation Chart. Chemicals, materials, parts, and equipment referenced in this document must be used and handled p

15、roperly. Each party is responsible for determining proper use and handling in its facilities. FORD LABORATORY TEST METHOD BI 159-01 Page 4 of 5 Copyright 2001, Ford Global Technologies, Inc. Flotation Evaluation Chart 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Mark test

16、variants which cause Slight, Medium and Heavy flotation. O.K. - Green Slight - Yellow Medium - Orange Heavy - Red FORD LABORATORY TEST METHOD BI 159-01 Page 5 of 5 Copyright 2001, Ford Global Technologies, Inc. Test Panel Coding Panel 1 FF1 GD1 TS1 2 FF1 GD1 TS2 3 FF1 GD1 TS3 4 FF1 GD2 TS1 5 FF1 GD2

17、 TS2 6 FF1 GD2 TS3 7 FF1 GD3 TS1 8 FF1 GD3 TS2 9 FF1 GD3 TS3 10 FF2 GD1 TS1 11 FF2 GD1 TS2 12 FF2 GD1 TS3 13 FF2 GD2 TS1 14 FF2 GD2 TS2 15 FF2 GD2 TS3 16 FF2 GD3 TS1 17 FF2 GD3 TS2 18 FF2 GD3 TS3 19 FF3 GD1 TS1 20 FF3 GD1 TS2 21 FF3 GD1 TS3 22 FF3 GD2 TS1 23 FF3 GD2 TS2 24 FF3 GD2 TS3 25 FF3 GD3 TS1 26 FF3 GD3 TS2 27 FF3 GD3 TS3