ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:40.34KB ,
资源ID:747075      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-747075.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD FLTM BJ 002-1-2001 STEAM EMULSIFICATION TEST ON OILS.pdf)为本站会员(appealoxygen216)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD FLTM BJ 002-1-2001 STEAM EMULSIFICATION TEST ON OILS.pdf

1、 FORD LABORATORY TEST METHOD BJ 002-01 Date Action Revisions 2001 07 23 Revised Editorial no technical change A. Cockman 1992 05 05 Printed copies are uncontrolled Page 1 of 2 Copyright 2001, Ford Global Technologies, Inc. STEAM EMULSIFICATION TEST ON OILS Application This procedure is used to deter

2、mine the resistance to emulsification with water of turbine and hydraulic mineral oils. Apparatus Required The apparatus required for the test (see diagram) consists of a liter boiling flask with Pyrex glass fittings, supported by a ring and stand, a 250 mL tall form graduate, a Bunsen burner and a

3、timing device such as a stop watch. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherw

4、ise specified. Procedure 1. Pour 30 mL of distilled water and 100 mL of the oil to be tested into the 250 mL graduate. Note: All glassware used for the test should be chemically clean. 2. Assemble the apparatus and adjust the flame of the Bunsen burner to generate enough steam to maintain a vigorous

5、 agitation of the oil and water in the graduate for a period of 10 minutes. Timing should not begin until the water first penetrates through the oil layer. 3. After steaming for the prescribed time, immediately open the pressure release valve, shut off the burner, remove the glass tubing from the gr

6、aduate and set the stop watch. 4. Record the progress of separation at the intervals required by the specification for the oil in question. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use a

7、nd handling in its facilities. FORD LABORATORY TEST METHOD BJ 002-01 Page 2 of 2 Copyright 2001, Ford Global Technologies, Inc. STEAM EMULSIFICATION TEST ON OILS A - 250 mL Tall Form Graduate B - 7 mm Glass Tubing C - 1000 mL Boiling Flask D - 3 Ft. High Column (7 mm Glass Tubing) E - Pressure Release Valve (Rubber Tubing and Pinch Clamp) F - Ring Stand and Support G - Bunsen Burner H - 60 Angle on Glass Tubing Apparatus for Steam Emulsification Test on Oils

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1