1、 FORD LABORATORY TEST METHOD BN 125-01 Date Action Revisions Rev. 1 2015 05 28 Revised See Summary of Revisions L. Schmalz, NA 2013 01 22 Activated Maria Dumitrescu; Mark Montgomery; Marcelo Fontes, Cheney Chen, Controlled document at www.MATS Copyright 2015, Ford Global Technologies, LLC Page 1 of
2、7 RESISTANCE TO LINT PICKUP AND LINT RETENTION OF FABRICS Application This test method determines the lint resistance and lint retention on automotive seat fabrics. This test uses a rotating platform to rub the test fabric against a reference piece of material under a fixed weight. The platform rota
3、tes on a 19 mm radius at approximately 58 revolutions per minute. Apparatus and Materials Required 1. Pilling Tester The pilling tester is described in ASTM D3511 and modified to hold the test fabric to the rotating platform. The round shaped lint cloth holder weight is 660 +/- 5 g, see Fig 1a. Sour
4、ce: Schap Specialty Machine, Inc. 17309 Taft Road Spring Lake, MI 49456 Phone (616) 846-6530 Fax: 616-846-6675 Email: 2. Vacuum cleaner, canister type, with a soft brush attachment Note: The vacuum used with the Taber test machine is acceptable when set to the highest power setting. The soft brush
5、attachment shall have approximately 45 mm long bristles. 3. Lint Cloth: Bleached Cotton style # 425. Source: Test Fabrics, Inc. PO Box 3026 415 Delaware Ave West Pittston, PA 18643 USA Phone: (570) 603 0432 Fax: (570) 603 0433 Email: or FORD LABORATORY TEST METHOD BN 125-01 Copyright 2015, Ford G
6、lobal Technologies, LLC Page 2 of 7 Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5% relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwi
7、se specified. Procedure 1. Cut two fabric specimens (see Fig 2) 2. Mount the fabric specimens face up on the lower wood board of the pilling tester, see Fig 3. Tightly secure the specimens to the board to prevent wrinkling. 3. Mount the lint cloth on the round shaped holder and secure with the rubbe
8、r “O“ ring as it shows in Fig 1b. Place the holder on the station with the fabric specimen. (see Fig 4) 4. Start the machine to rub the lint cloth on the face fabric for 30 seconds. Lint cloth must be replaced after every test. 5. Remove tested specimens from the wood board. Evaluate the tested spec
9、imen lying flat on the seat of an office chair and then pin it to the seat back. Report both the horizontal and vertical ratings. Label this test specimen “lint pickup“. 6. Vacuum the second specimen using 10 strokes (one stroke is the back and forth motion) with brush attachment. Evaluate the vacuu
10、med specimen lying flat on the seat of an office chair and then pin it to the seat back. Report both the horizontal and vertical ratings. Label this test specimen “lint retention“. Evaluation Compare the tested specimens to an untested fabric. Use the photographic standards on pages 5 and 6 to rate
11、the pick up and lint retention specimens using the following scale: Rating 4 - No linting less than 5 cotton fibers left on the fabric surface Rating 3 - Slight - slight cotton fiber left on the fabric surface Rating 2 - Moderate - large amount of fiber left on the fabric surface and/or a change in
12、the fabric Appearance Rating 1 - Severe- clumps of fibers entangled with the fabric surface or complete coverage of fabric surface by fiber Report the Rating for the lint pickup specimen and lint retention specimen. Chemicals, materials, parts, and equipment referenced in this document must be used
13、and handled properly. Each party is responsible for determining proper use and handling in its facilities. FORD LABORATORY TEST METHOD BN 125-01 Copyright 2015, Ford Global Technologies, LLC Page 3 of 7 Summary of Revisions 2015 05 28 -Removed from step 5 gently shake off the excess fibers and added
14、 statement on evaluating the sample flat and horizontal by pinning to an office chair - Added to step 6 statement on evaluating the vacuumed specimen on the vertical and horizontal by pinning to an office chair. -Updated rating 4 from no cotton fibers to less than 5 Fig. 1a Round shape holder for li
15、nt cloth Fig. 1b Mounted lint cloth on the round shape holder FORD LABORATORY TEST METHOD BN 125-01 Copyright 2015, Ford Global Technologies, LLC Page 4 of 7 Fig. 2 Specimen size Fig. 3 Specimens mounted on the lower wood board FORD LABORATORY TEST METHOD BN 125-01 Copyright 2015, Ford Global Techno
16、logies, LLC Page 5 of 7 Fig 4. Mounted samples ready for test FORD LABORATORY TEST METHOD BN 125-01 Copyright 2015, Ford Global Technologies, LLC Page 6 of 7 Photographic standard of Rating 4 Photographic standard of Rating 3 FORD LABORATORY TEST METHOD BN 125-01 Copyright 2015, Ford Global Technologies, LLC Page 7 of 7 Photographic standard of Rating 2 Photographic standard of Rating 1
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1