ImageVerifierCode 换一换
格式:PDF , 页数:2 ,大小:36.25KB ,
资源ID:747319      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-747319.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(FORD FLTM BO 021-1-2001 DETERMINATION OF FLOW RATIO OF POLYETHYLENES.pdf)为本站会员(livefirmly316)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

FORD FLTM BO 021-1-2001 DETERMINATION OF FLOW RATIO OF POLYETHYLENES.pdf

1、 FORD LABORATORY TEST METHOD BO 021-01 Date Action Revisions 2001 03 27 Editorial no technical change A. Cockman 1992 07 27 Printed copies are uncontrolled Page 1 of 2 Copyright 2001, Ford Global Technologies, Inc. DETERMINATION OF FLOW RATIO OF POLYETHYLENES Application This procedure is used to de

2、termine the flow ratio which gives an indication of the molecular weight distribution of polyethylene plastics. Apparatus Required Extrusion Plastometer (Melt Indexer) Source: Tinius Olsen Testing Machine Co. Willow Grove, PA or F. F. Slocom Corporation Wilmington, DE Weights (a) 2060 +/- 10 g weigh

3、t (b) Weights totalling 9,900 +/- 50 g (weights + piston = 10,000 +/- 50 g) Stop Watch Analytical Balance Beam Balance Preparation of Samples The test specimen may be in any form which can be introduced into the bore of the cylinder; for example, powder, granules, strips or molded slugs. Conditionin

4、g and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. FORD LABORATORY TEST METHOD BO 0

5、21-01 Page 2 of 2 Copyright 2001, Ford Global Technologies, Inc. Procedure 1. Determination of melt index. (See ASTM D 1238, Condition E) 2. Determination of flow index. (a) The total mass of the piston and weight shall be 10,000 +/- 50 g. The other conditions are the same as for the melt index. (b)

6、 Start the timer and place a full charge into the cylinder (7 to 9 grams), and put the piston and 2060 g weight in place. (The 2060 g weight is used during the preheat period only.) (c) After 3 minutes, force out enough of the charge by hand pressure so that after an additional 2 minutes, the cylind

7、er will be about one-half full. (d) After the additional 2 minutes (total of 5 minutes elapsed time), replace the 2060 g weight with the 9900 g weight and cut off and discard the extruded portion of the specimen at the orifice. (e) Collect the extrudate for the next 30 seconds. (f) Follow the cleani

8、ng procedure outlined in the melt index determination. (g) Weigh the 30 second extrudate to the nearest milligram and calculate the flow index as the rate of extrusion in grams per 10 minutes. weight of extrudate in grams x 10 = flow index time of extrudation in minutes 3. Determination of flow ratio. flow index = flow ratio melt index Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities.

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1